RANGE HOODS Models SEH2636 SEH2624 FELIX STORCH, INC. 770 Garrison Avenue Bronx, New York 10474 www.summitappliance.
TABLE OF CONTENTS Safety Warnings................................................................................................2-4 Location of Parts..................................................................................................5 Technical Specifications......................................................................................6 Dimensional Diagram...........................................................................................7 Installation..........................
LIMITED WARRANTY SUMMIT Appliance warrants this product to be free from defects in materials and workmanship for a period of one year from the date of original purchase or delivery. Any parts determined to be defective will be replaced by SUMMIT at no charge to you. Plastic parts, liners, and outer cabinets are warranted to be manufactured to commercially acceptable standards and free from defects at the time of delivery. This limited warranty does not apply to: 1. Improper installation 2.
WIRING DIAGRAM v. If the electrical cable is defective, it must be changed by the manufacturer or a qualified service technician. w. If there is a fire, cut off the power to the hood and cooking devices and cover the flame. Do not use water to extinguish the fire. CAPASITOR READ AND SAVE THESE INSTRUCTIONS WARNING! TO REDUCE THE RISK OF A RANGE-TOP GREASE FIRE: a. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite.
SEH2636 Model Model No 2170.9.579.01 Pos. Part No. Spare Part 1 2 YT971.1000.22 CARBON FILTER YT142.3150.06 ALUMINUM CASSETTE FILTER 3 YT207.1000.35 4 YT201.1000.22 CABLE FIXER(FOR CHIMNEY HOOD) CIRCUIT BOX COVER 5 YT201.1000.24 6 YT202.1000.16 7 8 YT460.1000.16 YT403.1000.10 9 YT404.1000.24 10 YT455.2120.01 YT458.2120.04 11 12 CIRCUIT BOX METAL VALVE BLOWER HALOGEN LAMP-50W POWER SUPPLY CORD LAMP HOLDER GROUP SLIDER BUTTON a.
EXPLODED VIEW LOCATION OF PARTS SEH2636 2170.9.579.
TECHNICAL SPECIFICATIONS SEH2624 Model Model No 2170.6.579.01 Pos. Part No. Model Voltage(V) 110-120 V Lamp (W) 2 x 50 W 1 2 YT971.1000.22 CARBON FILTER YT142.3150.06 ALUMINUM CASSETTE FILTER 3 YT207.1000.35 4 YT201.1000.22 CABLE FIXER(FOR CHIMNEY HOOD) CIRCUIT BOX COVER Control Type 5 YT201.1000.24 Motor Power (W) 6 YT202.1000.16 CIRCUIT BOX METAL VALVE 7 8 YT460.1000.16 BLOWER HALOGEN LAMP-50W POWER SUPPLY CORD Capacity (CFM) YT403.1000.10 9 YT404.1000.24 10 YT455.2120.
EXPLODED VIEW DIMENSIONAL DIAGRAM SEH2624 2170.6.579.01 WARNING! TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.
Hood does not operate X Illumination lamp does not illuminate X Check carbon filter. (If it operates with carbon filter, carbon filter should be replaced quarterly.) Check air outlet chimney. (Air outlet chimney should be open.) Check bulbs. (Bulbs should be in good conditions.) Check aluminum filter. (Aluminum cassette filter should be washed once a month under normal conditions.) Check lamp switch. (Lamp switch should be in on position.) Check motor switch.
REPLACEMENT OF LIGHTING COMPONENTS Fix the connector box to the motor junction plate with two 3,5 x 9,5 RYSB screws as shown. Disconnect the hood. Remove the aluminum cassette filter. In order to change the 50-watt halogen light bulb, refer to diagram below. (1) Press down on the back part of the lamp holder and (2) turn it counter-clockwise. Replace old bulb with new one. Turn in reverse direction when installing new bulb. INSTALLING MOUNTING BRACKETS 1.
* * * CLEANING AND MAINTENANCE Disconnect the device prior to maintenance (cut off its power supply by turning off the switch). The aluminum cassette filter holds oils and dust from the air. The metal filter must be washed in hot soapy water every month, if possible in the dishwasher at 140°F. To disassemble, press on the spring clamps at the edge of the cassette filter. (Do not reassemble before drying after cleaning.
4. Hang the range hood on the wall: Hang the range hood on screws A and B, then tighten the screws securely. Fix two screws into the C and D holes through the corresponding holes inside the hood. Assemble flexible aluminum tubing to the plastic fitting on the hood. Connect the other end of the tubing to the wall outlet. Assemble upper exhaust to lower exhaust. Place both parts on the range hood. Screw lower exhaust to the body using the side holes.
