BUILT-IN UNDERCOUNTER COMMERCIAL OUTDOOR BEER DISPENSER (KEGERATOR) SBC54OSBIADA Instruction Manual BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS NOTE: This unit is designed for the cooling and dispensing of beer only, and are not recommended for storing perishable foods such as meats or dairy products. Write Model and Serial Numbers here: Model _________________________ Serial No. ______________________ FELIX STORCH, INC.
IMPORTANT SAFEGUARDS Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the Safety Alert Symbol. This symbol alerts you to potential hazards that can kill or injure you and others. All safety messages will follow the Safety Alert Symbol and either the words DANGER or WARNING.
Use two or more people to move and install the appliance. Failure to do so can result in back or other injury. To ensure proper ventilation for your appliance, the front of the unit must be completely unobstructed. Choose a well-ventilated area with temperatures above 60°F (16°C) and below 90°F (32°C). The appliance should not be located next to ovens, radiators or other sources of high heat. The appliance must be installed with all electrical connections in accordance with state and local codes.
Location of Parts Twin taps Railing Temperature control dial (thermostat) and interior light CO2 canister holder Stainless steel door Front ventilation slots (kick plate) Compressor step Leveling legs NOTE: Models with suffix “NK” do not include a tap kit 4
Technical Information Model Number and Description SBC54OSBIADA 32.25” high for ADA compliant counters Capacity Two 1/6 kegs Electrical Input 115V AC/60Hz Rated Current 1.2A Defrost Automatic Refrigerant R600a (0.64 oz.)* Installation Built-in or free-standing Unit Dimensions (W x D x H) 23.75" x 24.75" x 32” (32.25" to hinge cap) NOTES: Models with “NK” in the suffix do not include tapping equipment. All models are ETL-S listed to NSF-7 standards for commercial use.
Installation Instructions Parts List Remove all packing materials and parts. Inspect to make sure all parts listed below are present and in good condition: 1 double draft arm assembly (with washer) 1 CO2 cylinder 1 CO2 regulator 2 keg taps (American Sankey type) 1 cleaning kit Vinyl tubing 1 stainless steel (removable) floor to protect the unit during keg insertion 1 drip tray Hose clamps Various screws Before Using Your Appliance: Remove the exterior and interior packing.
Electrical Connection: Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is damaged, have it replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. This unit should be properly grounded for your safety. The power cord of this unit is equipped with a three-prong plug which mates with a standard three-prong wall outlet to minimize the possibility of electrical shock.
Adjusting the Tilt If your beer cooler seems unsteady or you would like the door to close more easily, you can use the leveling legs to adjust the tilt of the unit. Be sure that the unit is in its final position when making adjustments to the tilt and that it is plugged into a grounded 3-prong outlet. WARNING: Two or more people are required to move and/or install the refrigerator. Failure to do so may cause back or other injury.
CO2 Regulator and CO2 Cylinder NOTE: Your CO2 cylinder is shipped empty to avoid any possible accidents during transportation. When you purchase the first keg of beer, have your beer distributor fill the CO2 cylinder. You must read and understand the following procedures for CO2 cylinders before installation: 1. Install the CO2 gas line tube to the regulator by attaching one end of the red tube to the hose connection on the CO2 regulator. 2.
d. Place the CO2 tank and CO2 regulator valve component into the cabinet and fix the CO2 tank with tank bracket and retainer (See Figure 8). 3. Install the beer keg: Note: This unit can hold two one-sixth barrel kegs, but not a full-size keg. Place the beer keg into the cabinet and firmly connect the keg’s opening to the connection port of the mixed ball valve.
Operating Your Kegerator Temperature Control: Your appliance’s evaporator system is out of sight behind the interior rear wall. The interior temperature is controlled with a thermostat knob located inside the unit, towards the upper right-hand corner. Turn the knob clockwise from the STOP (0) position toward the higher numbers for colder temperatures. Higher settings on the knob (higher numbers) mean lower temperatures (colder) in the kegerator.
Care and Maintenance Cleaning Your Appliance: 1. Unplug the appliance, turn the thermostat to STOP (0) and remove all contents, including shelves. 2. Wash the inside surfaces with a solution of lukewarm water and vinegar. Wipe dry with a clean, soft cloth. 3. Wash the outside cabinet with a solution of warm water and mild liquid detergent. Rinse well and wipe dry with a clean soft cloth. 4.
Draft Beer Troubleshooting Problem Cause Correction Beer is cloudy: The beer in the glass appears hazy and not clear. Excessively low temperatures may cause hazy or cloudy beer, particularly when the beer lies in the cold coil for long periods of time. Drain a few ounces before drinking. Glasses may not have been cleaned properly. Do not wash beer glasses together with glasses that have contained milk or any other fatty substance.
Beer has off taste: Often bitter and bite-y; sometimes completely lacking flavor and zest. It may also have an oily or foul odor which may carry an unpleasant taste. Improper cleaning of the tap Brush and clean the tap properly. It should be scoured using a detergent, then rinsed clean. Contaminated air line Beer tube should be examined. If contaminated, it should be replaced. Condensation is forming on the tap. It is normal to see condensation forming on the tap.
General Troubleshooting When using this appliance, you may come across some problems that in many cases result from improper handling and can easily be eliminated. TROUBLESHOOTING GUIDE The appliance fails to operate after being connected to the power source. Check whether the power supply is active and that the thermostat is not set to the STOP (0) position. The compressor is running continuously. The door was opened frequently or it was left open too long.
Limited Warranty ONE-YEAR LIMITED WARRANTY Within the 48 contiguous United States, for one year from the date of purchase, when this appliance is operated and maintained according to instructions attached to or furnished with the product, warrantor will pay for factoryspecified parts and repair labor to correct defects in materials or workmanship. Service must be provided by a designated service company. Outside the 48 states, all parts are warranted for one year from manufacturing defects.
