00LB. ICE MACHINE User Manual MODELS: BIM100, BIM100ADA, SCIM101, ALIM100 Write Serial No. of unit here: ________________________________ Felix Storch, Inc. Summit Appliance Division An ISO 9001:2015 registered company 770 Garrison Avenue Bronx, NY 10474 www.summitappliance.
TABLE OF CONTENTS Important Safety Instructions 3 Precautions 3 Grounding Instructions 4 Location of Parts 5 Installation Instructions 6-7 Before Using your Ice Maker 6 Installing the Ice Maker 6 Installing the Leveling Legs 6 Connecting the Water Line 7 Installing the Purification Filter 7 Operation 7-8 Ice Full Sensor 8 Ice Thickness Sensor 8 Changing the Purification Filter 8 Cleaning 8-9 Cleaning the Ice Bin 8 Cleaning the Condenser Filler 9 Cleaning the Condenser 9 U
IMPORTANT SAFETY INSTRUCTIONS READ ALL SAFETY INFORMATION BEFORE USING. WARNING: RISK OF CHILD ENTRAPMENT Child entrapment and suffocation are not problems of the past. Unused or abandoned icemakers are still dangerous, even if they will just “sit in the garage a few days.” • • Before you throw away your old icemaker, take off the doors. Leave any shelves or drawers in place so that children may not easily climb inside. Never allow children to operate, play with, or crawl inside the ice maker.
GROUNDING INSTRUCTIONS WARNING: Improper use of the grounding plug can result in a risk of electric shock. • • • This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This appliance is equipped with a power cord with a grounding wire and a grounding plug. The plug must be used with an outlet that is properly installed and grounded.
LOCATION OF PARTS (Front) (Rear) (Interior) 5
INSTALLATION INSTRUCTIONS Before Using the Ice Maker • • Remove any exterior or interior packaging. Attach the four leveling feet to the bottom of the appliance. NOTE: Before connecting the ice maker to a power source, let the appliance stand upright for approximately two hours. This will reduce the possibility of a malfunction in the cooling system from handling during transportation. • • • • Clean the interior surface with lukewarm water, using a soft cloth.
Connecting the Water Line Ice maker water supply Ice maker water drain Water Temperature 50 – 90◦ F • Water Pressure 20 – 80 psi • Water piping size 3/8 “ 3/4 “ (Rear) • • Connect a 3/8” diameter pipe to the tap water line. The pressure of the tap water line should be maintained at a level between 20psi (1.4bar) and 80psi (5.5bar). The tap water line and drain pipeline should be planned and prepared at the place of installation.
An automatic sensor stops ice making once the ice box is full. Remove the finished ice from the ice basin to resume the automatic ice making operation. Ice Thickness Sensor An ice bridge thickness of 3.2mm (.012”) is set as the factory default. Rotate the control screw counter-clockwise to make the ice bridge thinner, and clockwise to make the ice bridge thicker. Changing the Purification Filter When the purification filter is no longer active, the ice maker will not produce ice.
Cleaning the Condenser Filter 1. Pull the condenser filter up and out of the front panel. 2. Use a vacuum cleaner to remove any dust. 3. Wipe the filter with a solution of 10g (0.35oz) of a neutral detergent, such as baking soda, in 3L (0.8gal) of warm water. 4. Dry the filter with a clean, dry cloth, and replace the filter into the front panel of the appliance. Cleaning the Condenser 1. 2. 3. 4. Unscrew the two screws at the bottom of the front panel.
The ice scoop and ice damper must be sanitized separately in 0.26 gal (1L) of sanitizer diluted in 5.4 gal (20L) of water. Once the scoop, ice damper, and ice basin have been sanitized, reassemble all sanitized components. When the first sanitizing procedure is complete, remove the packing down from the ice basin by pulling downward. Remove the water inside the packing down, and insert it back into the ice vessel sheet. Conduct the sanitizing procedure two more times.
Water does not drain properly Ice making does not take place There are foreign materials in the drain hose. Water is not supplied into the water bowl. Remove any foreign materials from the drain hose. Ensure water line is connected. TECHNICAL SPECIFICATIONS Specification Item Unit BIM100, BIM100ADA, SCIM101, ALIM100 Maximum Ice Making (Based on 10℃) Kg /day (Lbs./day) 50(110.2) Freezing Capability Depth Size (Installed Height) Width 574(22.5) mm(inch) 520(20.4) Height Before 862(33.
LIMITED WARRANTY ONE-YEAR LIMITED WARRANTY Within the 48 contiguous United States, for one year from the date of purchase, when this appliance is operated and maintained according to instructions attached to or furnished with the product, warrantor will pay for factory-specified parts and repair labor to correct defects in materials or workmanship. Service must be provided by a designated service company. Outside the 48 states, all parts are warranted for one year from manufacturing defects.
