Installation Instructions and Manual

BEFORE OPERATING
BEFORE OPERATING
SHIPMENT ARRIVING DAMAGED:
IMPORTANT NOTES:
VISIBLE DAMAGE
If your shipment arrives with visible damage to
the box/carton, be sure the damage is noted on
the bill of freight or express receipt and signed
by the person making the delivery. File claim for
damages immediately, regardless of the extent of
damage.
CONCEALED DAMAGES
If damages are unnoticed until the refrigerator is
unpacked, notify the transportation company or
carrier immediately and file a concealed damage
claim with them. This should be done within (5)
days of the delivery date. Be sure to hold on to
the box/carton for inspection. We cannot assume
responsibility for damage or loss incurred in
transit.
Remove the exterior and interior packing.
Before connecting the appliance to the power
source, let it stand upright for approximately
24 hours. This will reduce the possibility of a
malfunction in the cooling system from handling
during transportation.
Clean the interior surface with lukewarm water
using a so cloth.
Install the handle on the drawer if not already
aached.
This refrigerator can be opened either from the
le or right side. The default way of opening the
zdoor is from the right side. If you want to open
the door from the le side, please follow the
instructions below.
NOTE: All the removed parts must be well kept for
the re-installation of the door
• Remove the exterior and interior packing.
• Check to be sure you have all of the following
parts:
• 3 Shelves
• 1 Glass Lid
• 1 Crisper
• 1 Instruction Manual
• Before connecting the unit to the power
source, let it stand upright for approximately
2 hours. This will reduce the possibility of
a malfunction in the cooling system from
handling during transportation.
• Clean the interior surface with lukewarm
water using a so cloth.
• This appliance is designed to be free standing
only, and should not be recessed or built-in.
• Allow 5 inches of space between the back
and sides of the unit, which allow proper
air circulation to cool compressor and
condenser.
• Place your unit on a floor that is strong
enough to support the unit when it is fully
loaded. To level your unit, adjust the two
leveling legs at the boom of the unit.
• Remove the three screws (6) that hold the
lower door hinge (5), keep the hinge for later
use.
• Remove the door from the upper pin (3), and
keep the padded surface upwards to prevent
the scratching
• Remove the upper hinge cover (1), remove
the two screw (2), hold the upper hinge(3),
save the hinge for later use.
• Remove the hole cover (1) and transfer it to
the same location on the opposite side.
• Insert the lower door hinge in the right side,
fix the lower right hinge by tightening all the
screws.
• Remove the pin cap (9) from the right side
of the upper frame of the door, and then
transfer it to the same location on the
opposite side.
• Put the door on the Lower Door Hinge(5),
keep the door level , and then fix the upper
hinge(3) to the body(4) by the screws
• Put on the upper hinge cover(1).
• Your unit has only one control for regulating
the temperature in the compartment. The
temperature control is located on the upper
right hand side of the compartment.
• The first time you turn the unit on, set the
temperature control to “6”.
• The range of the temperature control is from
position “OFF” to “6”. Aer 24 to 48 hours,
adjust the temperature control to the seing
that best suites your needs. The seing of “3”
should be
• To turn the appliance off, turn the
temperature control to ”OFF”.
BEFORE USING YOUR APPLIANCE
BEFORE INSTALLING YOUR UNIT
REVERSING THE DOOR SWING OF YOUR
APPLIANCE
SETTING THE TEMPERATURE CONTROL
FIGURE 2
(
POSITION AFTER DOOR REVERSAL
)
INSTALLING YOUR UNIT
It is recommended that you install the appliance in
a place where the ambient temperature is between
60°F and 90°F (16°C-32°C). If the ambient
temperature is above or below recommended
temperatures, the performance of the unit may
be affected. For example, placing your unit in
extremely cold or hot conditions may cause
interior temperatures to fluctuate. The operating
temperature range may not be reached.
PARTS AND FEATURES
1. Interior Light Cover
2. Temperature Control
Knob
3. Wire Shelves
4. Glass Shelf
5. Drawer
6. Leveling Leg
1. Upper hinge cover
2. Screw
3. Upper hinge
4. Door
5. Lower Door Hinge
7. Door Bar (2)
8. Can Dispenser
9. Condiment Bar
10. Door
11. Boom Hinge
12. Top Hinge
13. Top Hinge Cover
• Locate the unit away from direct sunlight and
sources of heat (stove, heater, radiator, etc.).
Direct sunlight may affect the acrylic coating
and heat sources may increase electrical
consumption. Extreme cold ambient
temperatures may also cause the unit not to
perform properly.
• Avoid locating the unit in moist areas.
• Plug the unit into an exclusive, properly
installed-grounded wall outlet. Do not
under any circumstances cut or remove
the third (ground) prong from the power
cord. Any questions concerning power and/
or grounding should be directed toward a
certified electrician or an authorized Products
service center.
• Aer plugging the appliance into a wall
outlet, allow the unit to cool down for 2-3
hours before placing food in the refrigerator
compartment.
FIGURE 1
(
NORMAL POSITION
)
6. Screw
7. Hole cover
8. Cabinet
9. Pin cap
• Turning the temperature control to “OFF”
position stops the cooling cycle but does not
shut off the power to the unit.
• If the unit is unplugged, has lost power, or
is turned off, you must wait 3 to 5 minutes
before starting the unit. If you aempt to
restart before this time delay, the unit will not
start.
NOTE