ROCK PICKER MODEL 700 Operator’s Manual MODEL 700 Rotary Rockpicker, Hyd. Direct Drive ROCK PICKER MODEL 700 IMPORTANT THE OPERATOR IS RESPONSIBLE FOR ADJUSTING THE MACHINE SINCE MACHINE DOES NOT COME “FIELD READY” FROM FACTORY. CAUTION READ & UNDERSTAND OPERATOR’S MANUAL BEFORE USING MACHINE. See www.summersmfg.com for the latest version of all Summers Operator’s Manuals SUMMERS MANUFACTURING CO., INC. WEB SITE: www.summersmfg.com MADDOCK, NORTH DAKOTA 58348.........................................
Warranty Summers warrants only products of its manufacture against operational failure caused by defective materials or workmanship which occur during normal use within 12 months from the date of purchase by the end user from Summers’ dealer.
GENERAL INFORMATION This book is composed of three basic sections: Safety, Operation and Parts. The Operation Section provides information for proper operation and maintenance of your Summers Rockpicker. The Parts Section provides a complete parts breakdown for the Model 700 Rockpicker. Reference to “Right” and “Left” in this book is determined when the machine is viewed from the rear. Parts are referenced in each drawing with the Summers Manufacturing Part Number.
NOTES ii
SECTION 1 - SAFETY SAFETY-ALERT SYMBOL This symbol is used to denote possible danger and care should be taken to prevent bodily injury. This symbol means: ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Definition of each Signal Word used in conjunction with the Safety-Alert symbol. DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. This signal word is to limited to the most extreme situations.
SECTION 1 - SAFETY SAFETY DECALS 1. KEEP SAFETY DECALS AND REFLECTORS CLEAN. 2. REPLACE missing or unreadable decals. New decals are available from your Summers dealer by ordering correct part number (PN) located in lower right hand corner. 1. SUMMERS DECAL (PN 8Z0079) 2. PINCH POINT HAZARD DECAL (PN 8Z0087) 3.
SECTION 1 - SAFETY 4. GENERAL INFORMATION DECAL (PN 8Z0220) 5. ROCKPICKER BATT WARNING DECAL (PN 8Z0230) 6.
SECTION 1 - SAFETY 7. AMBER REFLECTOR (PN 8Z0800) 8. RED-ORANGE REFLECTOR (PN 8Z0805) 9. RED REFLECTOR (PN 8Z0810) MAINTENANCE SAFETY 1. STOP engine, place all controls in neutral, set parking brake, remove ignition key and wait for all moving parts to stop before servicing, adjusting or maintaining. 2. BE CAREFUL when working around high pressure hydraulic system. 3. ALWAYS make sure that pressure is relieved from hydraulic circuits before serving or disconnecting from tractor. 4.
SECTION 2 - OPERATION AND MAINTENANCE INITIAL SETUP HITCH AND SPINDLE SETUP Install hitch with hydraulic cylinder on left side, attach hitch jack, safety chain, hydraulic hose stand and tip holder. Use appropriate lifting device, hitch assembly weighs 410 lbs. 16.5L X 16.1 Tire: Attach receiver tube with plate (8R6206) to frame with tube on top. See Page 3-8. NOTE: Remove safety transport lock pin located under rake AFTER hydraulic lines and cylinders have been filled with oil. BEFORE INITIAL OPERATION 1.
SECTION 2 - OPERATION AND MAINTENANCE INSTALLATION INSTRUCTIONS FOR ELECTRIC SOLENOID LIFT OPTION 1. When installing an Electric Solenoid Lift Option refer to following instructions and see breakdown on page 3-6. Mounting the switch. Mount switch to a secure support in a convenient location on the tractor. Route the red and white battery wires to a 12-volt battery. Attach the white battery wire to the NEGATIVE (-) terminal and the red battery wire to the POSITIVE (+) battery terminal.
SECTION 2 - OPERATION AND MAINTENANCE FIELD OPERATION CAUTION: NEVER run machine into a buried rock in an effort to dig rocks. Pry rock loose first. This machine is not designed to dig rocks. To do so will void the warranty. ADJUSTMENTS FOR PICKING: MODEL 700 ROTARY ROCKPICKER In typical field conditions, lower picking rake and check that frame is level. Adjust by resetting hitch piece (8D0720) height. The picking rake should be set at a depth to skim rocks off the ground.
SECTION 2 - OPERATION AND MAINTENANCE NO. 1. PROBLEM Reel runs too fast or too slow. NOTE: Reel speed should not exceed 35 RPM. 2. CAUSE CORRECTION Flow control valve Adjust flow control valve on rockpicker improperly adjusted. for desired reel speed. Flow control valve adjusts speed of reel only on the picking direction of rotation - not in reverse. PAGE Page 2-3 Adjustments for picking. Rake raises slowly Insufficient oil flow Inherent problem with certain model while reel is turning.
SECTION 3- PARTS 3-1
SECTION 3- PARTS 3-2
SECTION 3- PARTS 3-3
SECTION 3- PARTS 3-4
SECTION 3- PARTS 3-5
SECTION 3- PARTS 3-6
SECTION 3- PARTS HYDRAULIC SWING HITCH (Model 700) 8J6010 3/4-16ORB X #6JIC(M) 90° ADP 8D1660 8X0202 3/8" LN (8X0112) 3/4X2-1/4" 8S2990 HOSE CLMP (8D8500) DETAIL A 8X0110 3/4 X 1.
SECTION 3- PARTS 3-8
HUB AND AXLE COMPONENTS Assembly Notes: A. Before towing machine, pack wheel bearings and fill 1/2 of hub cavity with high quality bearing grease. B. Tighten axle nut to 45 ft.-lbs, loosen nut until first slot is aligned with hole in axle, install cotter pin and bend to Legend: retain. SMC Part Number INDUSTRY Part Number or Size 2.
SECTION 3- PARTS 3-10
Disc Valve Motors Integral Cross Over Relief Valve Technical Manual 2000 Series
Introduction Eaton Char-Lynn®, your proven low speed high torque motor supplier, now offers the Char-Lynn® 2000 Series motor with our proven Eaton Vickers® Screw-in Cartridge Valves integral to the motor. This compact and efficient package offers increased value and cost effectiveness to designing Eaton into your applications. Minimizing the use of hoses, tubing, and fittings will reduce production and assembly time significantly. 2000 Series Geroler® Element ............9 Displacements Flow LPM [GPM]....
Standard Mount Motors 1-1/4 inch Dia. Tapered Shaft 1-1/4 inch Dia.Shaft 56,7/54,3 * [2.23/2.14] 10,2/7,8 65,3/62,7 * [.40/.31] [2.57/2.47] SAE 6 B Splined Shaft 1 inch and 25 mm Dia.Shaft 1-1/4 inch Dia. Splined Shaft 32 mm Dia. Shaft 56,7/54,3 * [2.23/2.14] * 7/8 inch Dia. Splined Shaft 65,8/63,5 * [2.59/2.50] 52,4/49,7 * [2.06/1.96] 52,4/49,7 * [2.06/1.96] 42,2/39,8 * [1.66/1.57] X Port B Y Max.
Wheel Mount Motors 1 inch and 25 mm Dia.Shaft SAE 6 B Splined Shaft 1-1/4 inch Dia.Shaft 96,8/94,4 [3.81/3.72] 1-1/4 inch Dia. Splined Shaft 32 mm Dia. Shaft 7/8 inch Dia. Splined Shaft 106,0/103,6 [4.17/4.08] 96,8/94,4 [3.81/3.72] 1-1/4 inch Dia. Tapered Shaft 92,5/89,9 [3.64/3.54] 105,5/102,8 [4.15/4.05] 92,5/89,9 [3.64/3.54] 82,4/79,9 [3.24/3.14] 50,3/48,0 [1.98/1.89] X Port B Y Max.
Bearingless Motors Port for Internal or External Case Drain 157,5 [6.20] Max. (2) 127,0 [5.00] Dia. 101,60/101,47 [4.000/3.995] Pilot Dia. 13,85/13,33 [.545/.525] Dia. Thru (4) 119,2 [4.69] Sq. Max. 14,22 [.560] Min. (4) X 24,06/23,54 [.947/.927] Port B 6.7/6,0 [.26/.24] Y Max. 7/8-14 O-ring Staggered Ports, G 1/2 (BSP) Staggered Ports O-ring Seal Furnished with Motor 16,8/15,2 [.66/.
Model Code Model Code for 2000 Series Motors Sample Model Code: The following 24-digit coding system has been developed to identify all of the configuration options for the 2000 Series motor Use this model code to specify a motor with the desired features. All 24-digits of the code must be present when ordering. You may want to photocopy the matrix below to ensure that each number is entered in the correct box.
Model Code Model Code — 2000 Series Disc Valve Motors Sample Model Code: 1 2 3 M 0 2 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 0 0 0 0 Nos Feature Code Description Nos Feature 10, 11 Port Type AA 19, 20 Special Features (Hardware) 00 None 01 Viton Seals 10 Viton Shaft Seal 57 105 bar [1500 psi] Internal Cross Over Relief Valve (staggered 7/8” o-ring ports only) 58 120 bar [1750 psi] Internal Cross Over Relief Valve (staggered 7/8” o-ring ports only) 59 140 bar [200
Eaton 14615 Lone Oak Road Eden Prairie, MN 55344 USA Tel: 952 937-9800 Fax: 952 974-7722 www.hydraulics.eaton.com Eaton 20 Rosamond Road Footscray Victoria 3011 Australia Tel: (61) 3 9319 8222 Fax: (61) 3 9318 5714 Eaton Eaton Fluid Power GmbH Dr.-Reckeweg-Str. 1 D-76532 Baden-Baden, Germany Tel: +49 (0) 7221 682-0 Fax: +49 (0) 7221 682-788 © 2003 Eaton Corporation All Rights Reserved Printed in USA Document No.
Eaton Fluid Power Group Hydraulics Business USA 14615 Lone Oak Road Eden Prairie, MN 55344 USA Tel: 952-937-9800 Fax: 952-294-7722 www.eaton.com/hydraulics © 2008 Eaton Corporation All Rights Reserved Printed in USA Document No.
Eaton Fluid Power Group Hydraulics Business USA 14615 Lone Oak Road Eden Prairie, MN 55344 USA Tel: 952-937-9800 Fax: 952-294-7722 www.eaton.com/hydraulics © 2008 Eaton Corporation All Rights Reserved Printed in USA Document No. $ .0-0 5.
History of Summers Manufacturing Co., Inc. 1965 – Summers Manufacturing is founded by Harley Summers, who purchases patent rights for Goebel truck and pickup hoists from the Goebel Brothers of Lehr, ND. These hoists, produced in Harley Summers’ blacksmith shop the first year, were distributed nationwide by a Cincinnati, Ohio, dealer. With increasing sales, the company soon outgrows the small shop. Summers wins the Herman harrow contract, beginning the company’s Herman culti-harrow line.
Model 700 Rock Picker Superrollers Superchisel Coulter-Chisel Disk-Chisel Hydraulic Fold Coil Packer & Hydraulic Fold Rolling Chopper Mounted Harrows Rolling Choppers Superharrow Plus & Superharrow 2650 Diamond Disk & 2510 DT Supercoulter Plus © Copyright 2013 Summers Manufacturing Co., Inc. All Rights Reserved Rolling Baskets Ultra & Ultimate NT Supersprayer To find a dealer near you check out our website - www.summersmfg.com or call us at: 1 (800) 732-4347 SUMMERS Manufacturing Company, Inc.
