HF Coil Packer & Rolling Chopper Operator’s Manual HYDRAULIC FOLD ROLLING HF Coil Packer & Rolling Chopper HYDRAULIC FOLD 15’ - 57’ COIL PACKER 14’ - 62’ IMPORTANT THE OPERATOR IS RESPONSIBLE FOR ADJUSTING THE MACHINE SINCE MACHINE DOES NOT COME “FIELD READY” FROM FACTORY. 8Z1111 CHOPPER CAUTION READ & UNDERSTAND OPERATOR’S MANUAL BEFORE USING MACHINE. See www.summersmfg.com for the latest version of all Summers Operator’s Manuals. SUMMERS MANUFACTURING CO., INC. WEB SITE: www.summersmfg.
Warranty Summers warrants only products of its manufacture against operational failure caused by defective materials or workmanship which occur during normal use within 12 months from the date of purchase by the end user from Summers’ dealer.
INTRODUCTION This manual provides information about Safety, Assembly, Operation and Parts for the Summers Hydraulic Fold Coil Packer and Hydraulic Fold Rolling Chopper. Please refer to these sections before assembling or operating your machine. Reference to “Right” and “Left” in this book is determined when the machine is viewed from the rear. Parts are referenced in each drawing with the Summers Manufacturing Part Number. Use this Part Number when ordering replacement parts from your Summers dealer.
TABLE OF CONTENTS SECTION 1: SAFETY Safety-Alert Symbol & General Safety Practices............................................................ 1-1, 1-2 Safety Decals & Reflectors............................................................................................. 1-3 - 1-5 General Assembly Safety Practices.........................................................................................1-6 SECTION 2: ASSEMBLY 14’ to 44’ Set-Up Instructions...................................................
SECTION 1 - SAFETY SAFETY-ALERT SYMBOL This symbol is used to denote possible danger and care should be taken to prevent bodily injury. This symbol means: ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Definition of each Signal Word used in conjunction with the Safety-Alert symbol. DANGER WARNING CAUTION indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. This signal word is to limited to the most extreme situations.
SECTION 1 - SAFETY SAFETY DURING TRANSPORT 1. ONLY TOW at a safe speed. Use caution when making corners or meeting traffic. 2. USE a safety chain between tractor drawbar and implement hitch when transporting on public roads. 3. ALWAYS use transport locks when transporting on public roads. 4. COMPLY with local lighting, marking and maximum width regulations when transporting on highways. 5. Frequently check for traffice from rear, expecially during turns. SAFETY DECALS 1.
SECTION 1 - SAFETY 3. WING DANGER DECAL (PN 8Z0344) 4. ELECTROCUTION DANGER DECAL (PN 8Z0346) 5.
SECTION 1 - SAFETY 6. AMBER REFLECTOR (PN 8Z0800) 7. RED-ORANGE REFLECTOR (PN 8Z0805) 8. RED REFLECTOR (PN 8Z0810) SAFETY LIGHT OPERATION The Summers Safety Light Kit is equipped with a 7 pin connector. To protect 7 pin connector, store in dust cap (8K8067) when not attached to towing vehicle.
SECTION 1 - SAFETY REFLECTOR LOCATIONS Summers Mfg. Co., Inc.
SECTION 1 - SAFETY GENERAL ASSEMBLY SAFETY PRACTICES YOU ARE RESPONSIBLE for the safe assembly of the machine. DO NOT ALLOW CHILDREN or other unauthorized persons within the assembly area. BLOCK UP ANY RAISED PART of the machine. Be sure machine is stable after blocking. ALWAYS INSPECT LIFTING CHAINS AND SLINGS for damage or wear. WEAR PERSONAL PROTECTIVE EQUIPMENT which includes a hard hat, eye protection, work gloves and steel toed boots with slip resistant soles.
SECTION 2 - ASSEMBLY SET-UP INSTRUCTIONS – 14’ to 44’ HYDRAULIC FOLD IMPLEMENT Refer to illustrations on following pages and follow these steps when assembling an 14’ to 44’ Summers Hydraulic Fold Coil Packer or Hydraulic Fold Rolling Chopper. The machine should be placed in a firm, level area that allows ample room for assembly in field position. CAUTION: For safety purposes, block equipment while working on it. CENTER ASSEMBLY Place center section on stable supports approximately 2-1/2 ft. off floor.
SECTION 2 - ASSEMBLY C-SHANKS Mark frame with coil /chopper locations shown in layout drawing. Install C-Shanks (8K4392) and secure with hardware provided. COIL/CHOPPER ASSEMBLIES Pre-assemble Pull Frames. Secure pillow block to adjustment arm with 1/2” u-bolt and hardware. Secure bearing to coil shaft with set screws and snap ring. Attach Coil and Pull Frame assemblies to C-Shanks using ¾” U-bolts (8C1720) and hardware.
14’ Narrow Center 8C5850 8K8020 8C5145 8C5820 8C4515 8C4410 8D0720 57 1/4" 50 3/4" 54" 48" 6 1/4" 2-3 6 1/4" 8D8523 8K4396 48" 50 3/4" 54" 57 1/4" 8C5840 8K8010 8K7033 8C4515 8C5850 7/18/2012 9PD0140.
22’ Narrow Center 8C5200 8K7033 8C5820 114 1/4" 109 1/2" 104 3/4" 50 3/4" 54" 57 1/4" 6 1/4" 2-4 8C4410 8D8523 8C5060 8C5075 8C5840 86 1/2" 124 1/2" 8C4515 8K4396 8C5850 8C5180 8C5170 8C4410 8C5840 7/18/2012 9PD0220.
24’ Narrow Center 8C5075 8K7033 117 1/4" 124 1/2" 114" 110 3/4" 86 1/2" 8K4396 6 1/4" 8C4410 8K8010 8C5145 8C4510 2-5 8C5170 8C5820 8C5200 8C5180 50 3/4" 54" 57 1/4" 8C5850 8C4515 7/18/2012 9PD0240.
26’ Narrow Center 8C5075 123 1/4" 120" 165 1/2" 116 3/4" 86 1/2" 8K4396 8C5820 6 1/4" 8C5840 8C5145 8C5180 8C5170 2-6 SECTION 2 - ASSEMBLY 8C4410 8C4610 8C5860 8C5250 8K7033 8C5850 8C4515 50 3/4" 54" 57 1/4" 8C5850 8C4515 7/18/2012 9PD0260.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 28’ Narrow Center 8C5840 129 1/4" 126" 8C5075 122 3/4" 165 1/2" 6 1/4" 8C5170 86 1/2" 8K4396 8C5820 8C4410 8C5145 8C5180 8C5870 8K7033 8C5250 8C4710 8C5850 50 3/4" 8C4515 54" 57 1/4" 7/24/2012 9PD0280.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 30’ Narrow Center 8C5075 111 1/4" 108" 165 7/8" 8D3031 104 3/4" 86 1/2" 6 1/4" 8C5840 8C5170 8C5180 8K4396 8C5840 8C4410 8C5145 8K7033 8C5820 8C4410 8C5250 8C5840 8C4415 8C5850 8C4515 50 3/4" 54" 57 1/4" 149 3/4" 156" 159 1/4" 7/24/2012 9PD0300.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 26’ Standard Center 8C5090 8C5080 135 1/4" 132" 128 3/4" 160 1/2" 8C5210 6 1/4" 8C5150 8C5860 8C5820 8C5170 8C5840 8C4610 8C4410 8K7033 8C4410 8C5200 68 3/4" 8C4615 72" 75 1/4" 8C5860 8C4615 7/31/2012 2-9 9PD2675.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 28’ Standard Center 8C5090 8C5080 141 1/4" 138" 134 3/4" 160 1/2" 6 1/4" 8K4396 8C5850 8C5210 8C5150 8C5820 8C5850 8C5860 8C4510 8C5170 8C4510 8C4610 8K7033 8C5200 68 3/4" 8C4615 72" 75 1/4" 8C5860 8C4615 8/8/2012 2-10 9PD2875.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 30’ Standard Center 8C5090 8C5080 147 1/4" 144" 160 1/2" 140 3/4" 125" 6 1/4" 8K4396 8C5860 8C5820 8C5180 8C5150 8C5860 8C5210 8C4610 8C4610 8C4610 8C5170 8K7033 8C5200 68 3/4" 8C4615 72" 75 1/4" 8C5860 8C4615 8/8/2012 2-11 9PD3075.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 32’ Standard Center 8C5090 8C5080 153 1/4" 150" 160 1/2" 146 3/4" 125" 8C5170 8C5870 8K4396 6 1/4" 8C5820 8C5180 8C5150 8C5860 8C4710 8C5210 8C5870 8C4610 8C5170 8C4710 8K7033 8C5200 8C4615 68 3/4" 72" 8C5860 8C4615 75 1/4" 8/8/2012 2-12 9PD3275.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 34’ Standard Center 8C5090 8C5080 135 1/4" 132" 202" 128 3/4" 8D3031 151 1/2" 8K4396 8C5170 6 1/4" 8C5820 8C5150 8C5860 8C5180 8C5840 8C5260 8C5840 8C4410 8C4610 8C5170 8C4410 8K7033 8C5250 8C5840 8C5840 8C4415 8C4615 8C5860 68 3/4" 8C4615 72" 75 1/4" 176 3/4" 180" 183 1/4" 8/8/2012 2-13 9PD3475.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 36’ Standard Center 8C5090 8C5080 141 1/4" 138" 202" 134 3/4" 8D3031 125" 8K4396 8C5170 6 1/4" 8C5820 8C5150 8C5860 8C5260 8C5180 8C5850 8C5850 8C4510 8C4510 8C4610 8C5170 8K7033 8C5250 8C5840 8C5840 8C4415 8C4415 8C4615 8C5860 68 3/4" 8C4615 72" 75 1/4" 188 3/4" 192" 195 1/4" 8/8/2012 2-14 9PD3675.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 38’ Standard Center 8C5090 141 1/4" 8C5080 138" 186" 134 3/4" 8D3031 125" 6 1/4" 8K4396 8C5170 8C5820 8C5150 8C5860 8C5260 8C5180 8C5170 8C5850 8C5850 8C4510 8C5850 8C4510 8C4610 8K7033 8C5850 8C5250 8C4515 8C5860 8C4515 8C4615 8C5860 8C4615 68 3/4" 72" 75 1/4" 194 3/4" 198" 201 1/4" 8/8/2012 2-15 9PD3875.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 40’ Standard Center 8C5090 8C5080 147 1/4" 144" 196" 8D3031 125" 8K4396 8C5170 140 3/4" 6 1/4" 8C5820 8C5150 8C5860 8C5260 8C5180 8C5170 8C5860 8C5860 8C4610 8C5850 8C4610 8C4610 8K7033 8C5850 8C5280 8C4515 8C5860 8C4515 8C4615 8C5860 8C4615 68 3/4" 72" 75 1/4" 206 3/4" 210" 213 1/4" 8/8/2012 2-16 9PD4075.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 42’ Standard Center 8C5090 8C5080 147 1/4" 144" 202" 8C5180 8D3031 140 3/4" 125" 8K4396 6 1/4" 8C5820 8C5860 8C5150 8C5860 8C5860 8C5260 8C5180 8C5860 8C4610 8C4610 8C4610 8K7033 8C5280 8C5860 8C5860 8C4615 8C4615 8C4615 8C5860 8C4615 68 3/4" 72" 75 1/4" 212 3/4" 216" 219 1/4" 8/8/2012 2-17 9PD4275.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 44’ Standard Center 8C5090 243 1/4" 240" 236 3/4" 8C5080 217" 141 1/4" 138" 168" 134 3/4" 8D3031 125" 8K4396 8C5170 6 1/4" 8C5820 8C5840 8C5150 8C5860 8C5180 8C5180 8C5270 8C5840 8C5850 8C5850 8C4510 8C4410 8C4510 8C4610 8C5170 8C4410 8K7033 8C5280 8C5860 8C4415 8C5840 8C4415 8C4615 8C5860 8C4615 68 3/4" 72" 75 1/4" 188 3/4" 192" 195 1/4" 8/8/2012 2-18 9PD4475.
SECTION 2 - ASSEMBLY HYD. FOLD PACKER ASSEMBLY - PHOTO SUPPLEMENT – 42’ SHOWN Center 1. Position Center Frame on supports. 2. Install main and wing lift cylinder eye bolts (middle of adjustment). 4. Attach wing lift cylinders. 3. Install main lift cylinders.
SECTION 2 - ASSEMBLY HYD. FOLD PACKER ASSEMBLY - PHOTO SUPPLEMENT – 42’ SHOWN 5. Install Center Lift Arms and secure Pivot Pin with bolt, washer and lock nut. 6. Assemble Walking Axles. 7. Walking Axle with Pivot Bolt. 8. Install pivot dampeners. 9. Tighten Walking Axle hardware.
SECTION 2 - ASSEMBLY HYD. FOLD PACKER ASSEMBLY - PHOTO SUPPLEMENT – 42’ SHOWN 10. Connect rod end of main lift cylinder. 11. Position Walking Axle assembly. 12. Secure Walking Axle to Lift Arm. 13. Walking Axle Assembly installed. Wings 14. Connect rear Wings to Center. 15. Install wing pivot pins, secure with roll pins.
SECTION 2 - ASSEMBLY HYD. FOLD PACKER ASSEMBLY - PHOTO SUPPLEMENT – 42’ SHOWN 16. Connect from Wings to Center. 17. Left hand Wings attached. 18. Left hand Wings leveled for further assembly. 19. Rear view left hand Wings with Cross Brace. 20. Outside Cross Brace. 21. Inside Cross Brace.
SECTION 2 - ASSEMBLY HYD. FOLD PACKER ASSEMBLY - PHOTO SUPPLEMENT – 42’ SHOWN 22. Secure Cross Braces. 23. Outside Cross Brace. 24. Align Wings with Center, tighten u-bolts. 25. Install Wing Axle. 26. Left hand Wing Axle installed. Right hand Wing Axle installed.
SECTION 2 - ASSEMBLY HYD. FOLD PACKER ASSEMBLY - PHOTO SUPPLEMENT – 42’ SHOWN Hydraulic 27. Base End Wing Lift Cylinder. 28. Rod End Wing Lift Cylinder. 29. Base End Main Lift Cylinder. 30. Rod End Main Cylinder.
SECTION 2 - ASSEMBLY HYD. FOLD PACKER ASSEMBLY - PHOTO SUPPLEMENT – 42’ SHOWN 30a. Rod End Main Cylinder. 31. Hydraulic hose - Main and Wing Cylinders. Hitch Tubes 32. Install Hitch Tubes. 33. Attach Hitch Tubes to Center. 34. Attach Hitch Tubes to Center. 35. Rear u-bolt installed.
SECTION 2 - ASSEMBLY HYD. FOLD PACKER ASSEMBLY - PHOTO SUPPLEMENT – 42’ SHOWN 36. Front View. 37. Install Hitch Extension. 37. Install Hitch Extension. 38. Hose and Hydraulic Tip Holder. 39. Install Hitch.
SECTION 2 - ASSEMBLY HYD. FOLD PACKER ASSEMBLY - PHOTO SUPPLEMENT – 42’ SHOWN Hydraulic Hoses to Tractor & Tires 40. Pre-assemble front center fittings. 41. Front Center hose layout. 42. Tighten all hydraulic fittings. 43. Route hoses forward, secure with clamps. 43a. Install tires.
SECTION 2 - ASSEMBLY HYD. FOLD PACKER ASSEMBLY - PHOTO SUPPLEMENT – 42’ SHOWN Charge Hydraulic System MUST BE FREE TO ROTATE 44a. Extend and retract wing lift cylinders. 44b. Attach rod end of wing lift cylinders. 44c. Raise wings. 45. Adjust eye bolts so Wing rests on Center. 46. Tighten Wing Lift Cylinder eye bolts (above). 46. Tighten Main Lift Cylinder eye bolts (right).
SECTION 2 - ASSEMBLY HYD. FOLD PACKER ASSEMBLY - PHOTO SUPPLEMENT – 42’ SHOWN C-Shanks 48. Install clamps. 47. Mark frame using layout drawing, located clamps. 49. Install C-Shanks. 50. Tighten C-Shank mounting hardware.
SECTION 2 - ASSEMBLY HYD. FOLD PACKER ASSEMBLY - PHOTO SUPPLEMENT – 42’ SHOWN Coils 51. Lay out Coils and Pull Frames. 52. Identify Left and Right Hand Coils by comparing to bolt heads. 53. Bearing installed with snap ring. 54. Pre-assembly of 1/2” nuts on bearing attach u-bolt. 55. Bearing attached to Pull Frame.
SECTION 2 - ASSEMBLY HYD. FOLD PACKER ASSEMBLY - PHOTO SUPPLEMENT – 42’ SHOWN 55. Pre-assembled Coil with Pull Frame Tighten all hardware. 57. Center Coil and tighten set screws in bearings. 58. Roll Coil assemblies into position. 59. Position Coils. 9-1/2” C-C 12-1/2” C-C 60. Attach Pull Frames to C-Shanks, center mount shown. 61. 9-1/2 inch Center to Center C-Shank spacing, offset mount shown.
SECTION 2 - ASSEMBLY HYD. FOLD PACKER ASSEMBLY - PHOTO SUPPLEMENT – 42’ SHOWN 62. Assemble SMV Sign onto spade. 9-1/2” C-C Offset SMV Sign 63. Install SMV Sign. 64. Install Wing Transport Lock (Not used on 5 Section). Safety Lights 65. Front receiver.
SECTION 2 - ASSEMBLY HYD. FOLD PACKER ASSEMBLY - PHOTO SUPPLEMENT – 42’ SHOWN 67. Mounting flat. 68. Extension tube. 69. Mounting light bracket. 70. Front Right Amber Light installed. 71. Rear Red Light installed.
SECTION 2 - ASSEMBLY HYD. FOLD PACKER ASSEMBLY - PHOTO SUPPLEMENT – 42’ SHOWN Main Lift Transport Locks 72. Installed. 73. Storage position. 42. Hydraulic Fold Packer Drawbar 74. Front View 75. Front Left View. 76. Rear Right View.
8C9035 8K8020 8K8010 8C9055 8K8000 8C5145 8C5075 8D0720 6" 2-35 8C5060 51" 8D8523 8C9050 57 1/4" 57 1/2" 8C9030 NOTE: Decal shows correct orientation of Rolling Chopper. LEFT SIDE VIEW 8Z0210 8K7033 FRONT BACK 8C5820 7/24/2012 9RC0150.
8H1499 8H2310 8HD5583 8X0101 8HD5180 46 1/4" 16" 2-36 46" 8HD5583 8H2310 7/24/2012 9RC0150.
8K8020 8K8010 8K7033 8C5150 8C5820 8C5060 8D8523 8C9060 8K4396 2-37 4 3/4" 8D0720 8C5080 8C9055 67" 71 3/4" 76 1/2" 8C9035 7/24/2012 9RC0190.
8H2310 8HD5593 8HD5260 81 1/2" 2-38 41 1/4" 81 1/4" 8HD5290 8HD5593 8X0101 8H1499 8H2310 7/24/2012 9RC0190.
8C5075 105 1/2" 124 1/2" 100 3/4" 86 1/2" 96" 8C9030 8K4396 8C9050 8C9050 6" 8C5145 8C9030 SECTION 2 - ASSEMBLY 2-39 8C5170 8C5200 8K7033 8C5180 8C9030 47 1/2" 8C9050 8C5820 50 3/4" 54" 7/24/2012 9RC0210.
8H1499 8X0101 SECTION 2 - ASSEMBLY 8H1602 SHRT HI-CLR 2-40 8H2314 8H2310 8HD5563 16" 93" 118" 8HD5593 16" 93" 118" 7/24/2012 9RC0210.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 8K8010 8C5075 111" 106 1/4" 124 1/2" 8C5820 101 1/2" 8C9030 84" 8K4396 8C9050 6" 8K8020 8C9035 8C9055 8C5170 8C5180 8C5200 8K7033 8C9030 8C9050 47 1/2" 50 3/4" 54" 7/24/2012 9RC0230.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 8H1499 8X0101 8H1602 SHRT HI-CLR 8H1602 SHRT HI-CLR 8H1499 8H2310 8H2314 8H2314 8HD5150 8H2310 8HD5563 8HD5563 8HD5563 42 3/4" 91 1/4" 115 1/4" 42 3/4" 8HD5563 91 1/4" 115 1/4" 7/24/2012 9RC0230.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 8C5075 126 1/4" 119 3/4" 116 3/4" 86 1/2" 8C5170 8C9030 8C9050 8K4396 8C9040 113 1/4" 8K8010 6" 8C5145 8C5820 8K8020 8C9060 8C5200 8K7033 8C5180 8C9030 8C9050 47 1/2" 50 3/4" 54" 7/26/2012 9RC0265.iam/HYDFLD ROLLNG CHPR N-C26.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 8X0101 8K5515 8H2310 8HD5099 8J4290 8H2310 8H1499 8HD5150 8HD5563 8HD5563 8HD5563 8HD5583 42 3/4" 97" 126" 42 3/4" 97" 126" 7/26/2012 9RC0265.iam/HYDFLD ROLLNG CHPR N-C26.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 8C5075 166" 157 3/4" 89" 8K8010 8C5145 6" 9 1/2" 8C5185 8K8020 8C5185 8C5170 8C5250 8C5180 8C9030 46" 8C9050 55 1/2" 97 3/4" 50 3/4" 8K7033 102 1/2" 154 1/4" 107 1/4" 149 1/2" 159" 2-45 7/26/2012 9RC0300.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 8X0101 8H1499 8H2310 8J4290 8H2310 8HD5150 8HD5583 8HD5583 8HD5583 8HD5563 41 1/2" 117" 145" 41 1/2" 116 3/4" 144 3/4" 7/26/2012 9RC0300.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 8C5090 160 1/2" 154" 149 3/4" 124" 8K4396 8K8010 8C5820 141" 8C9030 8C9050 4 3/4" 8C5150 8C9040 8K8020 8C9060 8C5170 8K7033 8C5200 8C5180 8C9040 8C9060 62 3/4" 67 1/2" 72 1/4" 7/26/2012 9RC0320.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 8X0101 8HD5260 8H2310 8HD5270 8H2310 8H1499 8HD5563 8HD5563 8HD5593 40" 80 1/4" 133 1/4" 154 1/4" 8HD5593 40" 80 3/4" 133 1/4" 154 1/4" 7/26/2012 9RC0320.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 8C5080 138" 199 1/4" 8D3031 121 1/4" 8C9030 8C5170 133 1/4" 128 1/2" 8C9050 8C9050 8C5260 8K4396 4 3/4" 8C5820 8C9030 8K8010 8K8020 8C9030 8K7033 8C5180 8C9050 8C9040 63" 8C9060 67 3/4" 72 1/2" 177 1/4" 182" 186 3/4" 7/26/2012 9RC0345.iam/ HYDFLD ROLLING CHOPPER 34.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 8K5515 3/4 X 4 X 6" 8HD5260 8X0101 8H2314 8H1499 8HD5270 8J4290 8HD5099 8HD5099 8HD5583 8HD5583 8HD5583 8HD5593 149 1/2" 172 1/2" 149 1/4" 172 1/4" 7/26/2012 9RC0345.iam/ HYDFLD ROLLING CHOPPER 34.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 8C5090 8K8010 182" 144 1/4" 124" 8D3031 139 1/2" 8K4396 8C5170 134 3/4" 8C9030 8C9050 4 3/4" 8C5820 8C5150 8K8020 8C9030 8C5250 8K7033 8C5180 8C9050 8C9040 8C9060 62 3/4" 67 1/2" 72 1/4" 189" 193 3/4" 198 1/2" 7/26/2012 9RC0365.iam/HYDFLD ROLLING CHOPPER 36.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 8K5515 3/4 X 4 X 6" 8X0101 8HD5260 8H2310 8HD5270 8H2310 8H1499 8J4290 8HD5099 8HD5099 8HD5583 8HD5583 8HD5593 36" 82 1/4" 155 3/4" 175 3/4" 8HD5593 36" 82 1/4" 155 3/4" 175 3/4" 7/26/2012 9RC0365.iam/HYDFLD ROLLING CHOPPER 36.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 8C5090 8C5180 8K8010 8K8090A 197" 152 3/4" 188 5/16" 8D3031 148" 124" 8C9055 143 1/4" 8C9035 8C9055 4 3/4" 8C5185 8C5170 8C9035 8C5280 8K7033 8C9035 8C9055 69 1/4" 8C9040 74" 8C9060 8C5150 78 3/4" 204 1/2" 209 1/4" 214" 7/26/2012 9RC0400.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 8K5515 3/4 X 4 X 6" 8X0101 8HD5260 8H2310 8HD5270 8H2310 8H1499 8J4290 8HD5593 8HD5593 36" 8HD5593 83 1/2" 160 3/4" 190 3/4" 36" 8HD5593 83 1/2" 160 3/4" 190 3/4" 7/26/2012 9RC0400.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 8C5090 8K8010 201" 144 1/4" 192 1/4" 8D3031 139 1/2" 118" 134 3/4" 4 3/4" 8K8020 8C5260 8C9030 8C9055 8C9035 8C9050 8C5170 8C9040 8C5185 8C9055 8K7033 8C9040 8C9060 8C9040 8C9040 8C5150 8C9060 62 3/4" 67 1/2" 8C9060 8C9060 72 1/4" 208" 212 3/4" 217 1/2" 7/26/2012 9RC0425.iam/HYDFLD ROLLING CHOPPER 42.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 8X0101 8K5515 3/4 X 4 X 6" 8H1499 8HD5260 8H2310 8HD5180 8H2314 8H1499 8H2310 8J4290 8HD5099 8HD5099 8HD5563 8HD5563 8HD5563 29" 8HD5593 77" 124 1/4" 8HD5180 148 1/4" 194 3/4" 212 3/4" 41" 8HD5563 8HD5583 77" 124 1/4" 148 1/4" 194 3/4" 213" 7/26/2012 9RC0425.iam/HYDFLD ROLLING CHOPPER 42.
SECTION 2 - ASSEMBLY SET-UP INSTRUCTIONS – 46’ to 62’ HYDRAULIC FOLD IMPLEMENT Refer to illustrations on following pages and follow these steps when assembling a 46’ to 62’ Summers Hydraulic Fold Coil Packer or Hydraulic Fold Rolling Chopper. The machine should be placed in a firm, level area that allows ample room for assembly in field position. CAUTION: For safety purposes, block equipment while working on it. CENTER ASSEMBLY Place Packer drawbar center section on stable supports approximately 2-1/2 ft.
SECTION 2 - ASSEMBLY HYDRAULIC SYSTEM Install cylinder hydraulic fittings and hydraulic hoses between cylinders. HITCH TUBES Position hitch tubes on top of center section. Attach hitch tubes to center section with ¾” u-bolts, lockwashers and nuts. Connect hitch tubes with hitch extension, hitch channel (8C5050) and hitch piece (8D0720) at front of machine using hardware provided. 46’ to 50’ ONLY Install front cross brace below hitch tubes with ½” and ¾” u-bolts.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 8C5080 8C5090 255 1/4" 285" 180 1/2" 8K4396 8C5402 141 1/4" 138" 134 3/4" 125" 8C5120 252" 248 3/4" 8D3031 6 1/4" 8C5840 8C5135 8C5190 8C5300 8C5850 8C5860 8C5170 8C5840 8C5850 8C4510 8C4410 8C4510 8C4610 8C5850 8C5310 8K7033 8C5850 8C4410 8C5180 8C4515 8C5860 8C5860 8C4615 68 3/4" 72" 75 1/4" 8C4515 8C4615 194 3/4" 198" 201 1/4" 2/22/2013 2-59 9PD4675.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 8C5080 8C5090 261 1/4" 258" 254 3/4" 285" 141 1/4" 180 1/2" 138" 125" 8C5170 8C5135 6 1/4" 8C5190 8C5300 8C5402 8C5850 8D3031 8C5120 8C5130 8K4396 134 3/4" 8C5300 8C5860 8C5850 8C5850 8C5850 8C4510 8C4510 8C5402 8C4610 8C5310 8C4510 8C4510 8C5180 8C5310 8K7033 8C5850 8C5850 8C5860 8C4515 8C4515 8C5860 8C4615 68 3/4" 72" 75 1/4" 8C4615 194 3/4" 198" 201 1/4" 8/10/2012 2-60 9PD4875.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 8C5080 8C5090 267 1/4" 264" 260 3/4" 285" 141 1/4" 180 1/2" 138" 125" 8C5860 8D3031 8C5120 8C5130 8K4396 134 3/4" 8C5135 6 1/4" 8C5170 8C5190 8C5300 8C5402 8C5300 8C5860 8C5850 8C5402 8C5860 8C5850 8C4510 8C4610 8C4610 8C5310 8C4510 8C4610 8C5180 8C5310 8K7033 8C5850 8C5850 8C5860 8C4515 8C5860 8C4515 8C4615 68 3/4" 72" 75 1/4" 8C4615 194 3/4" 198" 201 1/4" 8/10/2012 2-61 9PD5075.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 8C5094 8C5084 8C5110 135 1/4" 310" 230 1/4" 227" 223 3/4" 132" 205 5/8" 128 3/4" 151 1/2" 8C5152 8D3031 8C5132 8K4396 6 1/4" 8C5840 8C5402 8C5840 8C4410 8C4610 8K7033 8C5180 8C5850 8C5840 8C5840 8C5840 8C4410 8C4515 8C5370 8C5860 8C4410 8C5170 8C5192 8C5137 8C4410 8C5370 8C5840 8C4415 8C4415 8C5860 8C5860 8C4615 68 3/4" 8C5850 8C4515 8C4615 72" 75 1/4" 176 3/4" 180" 183 1/4" 278 3/4" 282" 285 1/4" 8/10/2012 2-62 9PD5275.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 8C5094 8C5084 8C5110 135 1/4" 310" 230 1/4" 227" 223 3/4" 132" 205 5/8" 128 3/4" 151 1/2" 8C5152 8D3031 8C5132 8K4396 6 1/4" 8C5840 8C5402 8C5370 8C5860 8C5840 8C5840 8C5840 8C4410 8C5170 8C5192 8C5137 8C4410 8C4410 8C4610 8K7033 8C5180 8C5860 8C4410 8C5370 8C5840 8C5860 8C4615 8C5840 8C4415 8C5860 8C5860 8C4615 68 3/4" 72" 75 1/4" 8C4415 8C4615 8C4615 176 3/4" 180" 183 1/4" 284 3/4" 288" 291 1/4" 8/10/2012 2-63 9PD5475.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 8C5094 8C5084 8C5110 135 1/4" 310" 230 1/4" 227" 223 3/4" 132" 205 5/8" 128 3/4" 151 1/2" 8C5152 8D3031 8C5132 8K4396 8C5402 6 1/4" 8C5840 8C5370 8C5860 8C5840 8C5840 8C5840 8C4410 8C5170 8C5192 8C5137 8C4410 8C4410 8C4610 8K7033 8C5180 8C5870 8C4410 8C5370 8C5840 8C5870 8C4715 8C5840 8C4415 8C5860 8C5860 8C4615 68 3/4" 72" 75 1/4" 8C4415 8C4715 8C4615 176 3/4" 180" 183 1/4" 289 3/4" 293" 296 1/4" 8/10/2012 2-64 9PD5675.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 8C5094 8C5084 8C5110 333" 310" 326 1/4" 323" 319 3/4" 135 1/4" 132" 128 3/4" 219 3/8" 205 5/8" 151 1/2" 230 1/4" 227" 223 3/4" 8C5152 8D3031 8C5132 8K4396 8C5840 6 1/4" 8C5840 8C5412 8C5370 8C5860 8C5840 8C5840 8C5840 8C5840 8C4410 8C5170 8C5192 8C5137 8C4410 8C4410 8C4610 8C4410 8C4410 8C4410 8C5160 8C5160 8C5840 8K7033 8C5180 8C5370 8C5840 8C5840 8C4415 8C5840 8C4415 8C5860 8C5860 8C4615 68 3/4" 72" 75 1/4" 8C4415 8C4415
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 8C5094 8C5084 8C5110 325 1/16" 310" 336 1/4" 333" 329 3/4" 135 1/4" 132" 128 3/4" 219 3/8" 205 5/8" 151 1/2" 230 1/4" 227" 223 3/4" 8C5152 8D3031 8C5132 8K4396 8C5840 8C5412 6 1/4" 8C5840 8C5370 8C5860 8C5840 8C5840 8C5840 8C5840 8C4410 8C5170 8C5192 8C5137 8C4410 8C4410 8C4610 8C4410 8C4410 8C4410 8C5160 8C5160 8C5850 8K7033 8C5180 8C5370 8C5850 8C5840 8C4515 8C5840 8C4415 8C5860 8C5860 8C4615 68 3/4" 72" 75 1/4" 8C4415 8C4
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 8C5094 8C5084 8C5110 325 1/16" 310" 336 1/4" 333" 329 3/4" 135 1/4" 132" 128 3/4" 219 3/8" 205 5/8" 151 1/2" 230 1/4" 227" 223 3/4" 8C5152 8D3031 8C5132 8K4396 8C5860 6 1/4" 8C5840 8C5412 8C5370 8C5860 8C5840 8C5860 8C5840 8C5840 8C4410 8C5170 8C5192 8C5137 8C4410 8C4410 8C4610 8C4410 8C4610 8C4610 8C5160 8C5160 8C5840 8K7033 8C5180 8C5370 8C5840 8C4415 8C5840 8C4415 8C5860 8C5860 8C4615 68 3/4" 72" 75 1/4" 8C4415 8C5840 8C44
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 2-68
SECTION 2 - ASSEMBLY 5-Section Hydraulic Fold Coil Packer Assembly Instructions – Photo Supplement – 60’ Shown 1 1A 2-69
SECTION 2 - ASSEMBLY 2 3 2-70
SECTION 2 - ASSEMBLY 4 5 WING STOP 4X 51’-62’ 2X 46’-50’ REAR ONLY 2-71
SECTION 2 - ASSEMBLY 6 7A 7 2-72
SECTION 2 - ASSEMBLY 8 IMPORTANT Do Not over tighten. Bolt must be free to rotate. IMPORTANT Do Not route hydraulic hoses above wing stop.
SECTION 2 - ASSEMBLY 9A 10 2-74
SECTION 2 - ASSEMBLY 11 12 2-75
SECTION 2 - ASSEMBLY 13 14 15 2-76
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 8C5090 258" 253 1/4" 248 1/2" 285" 144 1/4" 180 1/2" 8C5170 139 1/2" 125" 8K4396 8D3031 8C5820 8C9030 8C9035 8C9055 134 3/4" 8K8010 8C5120 8C9050 8C5135 4 3/4" 8K8020 8C9035 8C9055 8C5402 8C5310 8C9030 8K7033 8C9050 8C9040 62 3/4" 8C9060 8C5139 8C5150 8C5139 67 1/2" 72 1/4" 191 3/4" NOTE: Decal shows correct orientation of Rolling Chopper. 196 1/2" 201 1/4" LEFT SIDE VIEW 8Z0210 FRONT BACK 2-77 7/26/2012 9RC0475.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 8K5515 3/4 X 4 X 6" 8H2310 8H2310 8X0101 8HD5260 8HD5270 8HD5563 8H1499 8H1499 8J4290 8HD5583 8HD5583 8HD5593 8HD5593 40" 76 3/4" 156 1/4" 174 1/4" 244 3/4" 270 3/4" 8HD5563 40" 77" 156 1/4" 174 1/4" 245" 270 3/4" 7/26/2012 9RC0475.iam/HYDFLD ROLLING CHOPPER 47.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 8C5084 230 1/4" 229 3/4" 220 3/4" 133" 8K8010 131 3/4" 122 1/4" 8K8020 8C5152 8C5192 8C5132 8D3031 8C5170 8C5402 8C5180 8K4396 8C5132 8C9050 8C5139 (4X) 4 3/4" 8C9050 8C5185 8C9030 8C9050 8C9050 8C9050 8C9050 8K7033 8C5156 8C5152 8C9050 8C9030 8C5370 8C9040 151 1/2" 228 1/4" 310" 8C9050 62 3/4" 8C9060 205 3/4" 8C9050 67 1/2" 72 1/4" 179" 183 3/4" 188 1/2" 277 3/4" 282 1/2" 287 1/4" 2-79 7/26/2012 9RC0510.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 8K5515 8X0101 8H2310 8HD5260 8H2310 8H1499 8HD5270 8HD5563 8H1499 8J4290 8HD5593 8HD5593 42" 8HD5593 67 1/2" 159" 199" 268 1/2" 282 1/2" 8HD5563 42" 8HD5593 67 1/2" 159" 199 1/4" 268 1/2" 282 1/2" 7/26/2012 9RC0510.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 8C5110 8C5094 310" 205 3/4" 151 1/2" 231 3/4" 230 1/4" 220 3/4" 8D3031 8K4396 8C5820 8C5132 8C5152 122 1/4" 8C9050 4 3/4" 8C9050 8C9030 8C5402 133" 131 3/4" 8C9050 8C5139 (4X) 8C5180 8C9050 8C9030 8C9030 8K7033 8C9030 8C5185 8C5180 8C5156 8C5185 8C9030 8C9035 8C9055 8C9050 8C9040 8C5370 8C9060 62 3/4" 67 1/2" 72 1/4" 179" 183 3/4" 188 1/2" 284 1/4" 289" 293 3/4" 7/26/2012 9RC0535.iam/HYDFLD ROLLING CHOPPER 53.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 8K5515 3/4 X 4 X 6" 8H1499 8X0101 8HD5260 8H2314 8HD5150 8H2310 8H1499 8H2310 8HD5270 8J4290 8HD5563 8HD5563 8HD5563 8HD5563 8HD5593 24" 77" 161" 219" 268 1/2" 289" 8HD5563 8HD5563 8HD5583 42" 77 1/4" 161" 219" 268 1/2" 289 1/4" 7/26/2012 9RC0535.iam/HYDFLD ROLLING CHOPPER 53.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 8C5110 8C5094 231 3/4" 230 1/4" 220 3/4" 205 3/4" 193 1/2" 133" 131 3/4" 122 1/4" 151 1/2" 8C5180 8K4396 8C5402 8C5180 8C5820 8C9040 8C9030 8C9050 8K8010 8C9050 8C5140 (4X) 8C9030 8K8020 8D3031 8C5137 4 3/4" 8C5185 8C5156 8C5192 8C9060 8C9050 8K7033 8C5370 8C9030 62 3/4" 8C9040 8C9060 67 1/2" 72 1/4" 179" 183 3/4" 188 1/2" 294 1/2" 299 1/4" 304" 7/26/2012 9RC0570.
SECTION 2 - ASSEMBLY SECTION 2 - ASSEMBLY 8K5515 3/4 X 4 X 6" 4 3/4" 8X0101 8HD5260 8H2310 8H1499 8HD5270 8H1499 8J4290 8HD5099 8HD5099 8HD5593 8HD5583 8HD5593 8HD5593 36" 86 3/4" 157 3/4" 199" 276 3/4" 299 1/4" 8HD5583 8HD5593 36" 87" 157 3/4" 199 1/4" 276 3/4" 299 1/2" 7/26/2012 9RC0570.
SECTION 3 - OPERATION and MAINTENANCE OPERATING INSTRUCTIONS – HYDRAULIC FOLD IMPLEMENT IMPORTANT: Do not exceed 20 MPH while transporting Implement. Do not attempt to raise or lower Implement unless it is securely attached to an appropriate towing vehicle. TRANSPORT TO FIELD POSITION 1. Hitch machine to tractor or implement using a locking hitch pin and safety chain. Connect hydraulic hoses and wiring connector. Retract hitch jack and rotate into storage position. 2.
SECTION 3 - OPERATION and MAINTENANCE UNHITCHING MACHINE 1. Select a level area to park machine. Block wheels to prevent machine from rolling. 2. Rotate jack into standing position and extend jack. Disconnect hydraulic hoses and wiring connector. Disconnect hitch and safety chain. NOTE: Operating implement in wet conditions will cause: 1. Excessive packing with possible soil surface crusting. 2. Increased implement frame stress. Discontinue use of Packer if mud builds up on coils.
SECTION 3 - OPERATION and MAINTENANCE PROPER BOLT USE DO NOT use these values if a different torque value or tightening procedure is given for a specific application. Torque values listed are for general use only. Check tightness of fasteners periodically.
SECTION 3 - OPERATION and MAINTENANCE 3-4
SECTION 4 - PARTS PARTS SECTION HYDRAULIC FOLD COIL PACKER & HYDRAULIC FOLD ROLLING CHOPPER 4-1
8K8090A 8D8500 8S1124 8X0110 3/4 X 1.
SECTION 4 - PARTS SECTION 4 - PARTS HYDRAULIC FOLD IMPLEMENT 18'-50' STANDARD CENTER 8A1004 5" HC 8X0285 1 1/2" N 8K5515 3/4 X 4 X 6" 8Z1000 8X0306 3/4" LW 8K1682C 8K1682C 8X0260 3/4" N 8X0260 3/4" N 8X0110 3/4 X 1.
SECTION 4 - PARTS SECTION 4 - PARTS HYDRAULIC FOLD IMPLEMENT 51' - 62' CENTER 8X0285 1 1/2" N 8X0260 3/4" N 8K1682C 8X0285 1 1/2" N 8X0306 3/4" LW 8C5152 8C5140 8C1750 3/4 X 3 X 5-1/2" 8K5515 3/4 X 4 X 6" 8X0110 3/4 X 1.
SECTION 4 - PARTS SECTION 4 - PARTS WING ASSEMBLY 3-SECTION IMPLEMENT 21' - 44' 8C6010 8C6000 8X0281 NY-LOCK 1" 8C6000 8C6010 32' SHOWN 8X0281 NY-LOCK 1" 8C5200 (21'-32' STD CNTR) 8C6010 8X0326 1-1/4" ID FW 8X0260 3/4" N 8X0306 3/4" LW 8X0260 3/4" N 8X0306 3/4" LW 8C5180 8K9108 8C5180 8X0260 3/4" N 8X0140 1 X 7" 8X0306 3/4" LW 8C6010 8X0140 1 X 7" 8X0528 3/8x2-1/2" RP 8C5280 8X0326 1-1/4" ID FW 8K5515 3/4 X 4 X 6" 8C5210 (21'-32' STD CNTR) 8K9108 8C5180 8X0528 3/8x2-1/2" RP 44' SHOWN
SECTION 4 - PARTS SECTION 4 - PARTS WING ASSEMBLY 5-SECTION IMPLEMENT 46' - 62' (LEFT HAND 62' SHOWN) 8X0140 1 X 7" 8C5310 (46'-50') 119.8" 8C5370 (51'-62') 145" 8C6010 8C6000 8C6010 8X0281 NY-LOCK 1" 8X0528 3/8x2-1/2" RP 8C5192 8C5180 8K5515 3/4 X 4 X 6" 8K9108 8X0281 NY-LOCK 1" 8X0326 1-1/4" ID FW 8C5300 (46'-50') NO CYL.
SECTION 4 - PARTS PACKER COIL MOUNTING ASSEMBLY 8X0119 3/4 X 7-1/2" 8C5820 8C5840 (4') 8C5850 (5') 8C5860 (6') 8C5870 (7') 8X0725 1/8" ZERK 8X0306 3/4" LW 8X0260 3/4" N 8X0306 3/4" LW 8X0242 NY-LOCK 1/2" N 8X0303 1/2" LW 8X0728 8X0260 3/4" N 8K4396 8C0216 BEARING COMPLETE 8C2002 FLAT 8C1751 3/4 X 3 X 6" 8C0150 8X0240 1/2" N 8C1740 1/2 X 4-1/4 X 7-1/4" COIL W/SHAFT PN 8C4410 - 4' (L) - (SHOWN) 8C4415 - 4' (R) 8C4510 - 5' (L) 8C4515 - 5' (R) 8C4610 - 6' (L) 8C4615 - 6' (R) 8C4710 - 7' (L) 8C4715
SECTION 4 - PARTS 4-8
SECTION 4 - PARTS HYDRAULIC LIFT IMPLEMENT HYDRAULIC ASSEMBLY 21' - 30' NARROW CENTER UNITS 8C0432 (2X) 4 X 32" 8D9418A - SEAL KIT ROD 8J6010 8D9316 (2X) 3.
SECTION 4 - PARTS 4-10
SECTION 4 - PARTS NOTE: SEE PHOTOS PAGES 2-69 THROUGH 2-76 FOR HOSE ROUTING.
SECTION 4 - PARTS SECTION 4 - PARTS NOTE: SEE PHOTOS PAGES 2-69 THROUGH 2-76 FOR HOSE ROUTING.
8C9070 (4') 8C9075 (5') 8C9080 (7') ROLLING CHOPPER ASSEMBLY 8C9030 (4') 8C9035 (5') 8C9040 (7') FRAME ROLLING CHOPPER ASSEMBLY BLADE 3/8x3 - 16-3/8" ASSEMBLY WIDTH 4' 5' 7' 8X0117 3/4 X 7" 8C9017 8X0244 1/2" FLG TOP LOCK NUT 8C5820 8X0064 CRG 1/2 X 1-1/2" 4-13 8K4396 8X0306 3/4" LW 8X0240 1/2" N 8X0265 3/4" LN 8X0260 3/4" N 8X0246 1/2" FN 8C2002 8C0150 8C1751 3/4 X 3 X 6" NOTE: Decal shows correct orientation of Rolling Chopper.
HUB AND AXLE COMPONENTS Assembly Notes: A. Before towing machine, pack wheel bearings and fill 1/2 of hub cavity with high quality bearing grease. B. Tighten axle nut to 45 ft.-lbs, loosen nut until first slot is aligned with hole in axle, install cotter pin and bend to retain. 2. INNER BEARING 8G8220 8G8217 8G8230 8G8230 8G8211 SE10 L44643 8L44610 L44610 HDA211 H517 8D5234 8D5236 8D5238 8D5217 8D5332 8D5336 LM48548 LM48510 H611 8D5221 8D5317 SE13 H211 4-14 H614 HD812 3.
8W1897 8H1394 8H1327 8H1309 8D5219 8X0269 8H2131A 8H1315 4-15 8X0099 5/8" X 6-3/4" 8X0100 5/8" X 8" (GR8 RLLNG BSKT) 8X0101 5/8" X 8" (GR5 MNTD HRRW) 8X0250 5/8" N 8W1204 1/2 X 3 X 3" 8X0261 3/4" LN 8X0123 3/4" X 5.
SECTION 4 - PARTS 4-16
SECTION 5 - PART NUMBERS & DESCRIPTIONS PART NUMBERS WITH DESCRIPTIONS 5-1
SECTION 5 - PART NUMBERS & DESCRIPTIONS 7C1726 7C4040 7C4050 7C4055 7C4060 7C4070 8A1155 8A1156 8A1157 8A4048 8A4050 8A4052 8A4054 8C0150 8C0202 8C0206 8C0250 8C0270 8C0432 8C0532 8C0535 8C0650 8C1470 8C1700 8C1710 8C1718 8C1720 8C1736 8C1740 8C1750 8C1755 8C1760 8C2300 8C2310 8C2316 8C2320 8C2330 8C2340 8C4410 8C4415 8C4510 8C4515 8C4560 8C4565 8C4610 8C4615 8C4710 8C4715 8C5050 8C5060 8C5070 8C5080 8C5084 8C5090 8C5094 8C5097 8C5100 8C5110 8C5115 8C5120 8C5130 8C5132 8C5135 8C5137 TUBE 2-5/8X2.026ID- 6.
SECTION 5 - PART NUMBERS & DESCRIPTIONS 8D5219 8D5221 8D5312 8D5314 8D5316 8D5317 8D5319 8D5332 8D5334 8D5336 8D8490 8D8500 8D8521 8D8522 8D8523 8D9102 8D9108 8D9110 8D9111 8D9216 8D9250 8D9316 8D9350 8D9416 8D9418A 8G2281 8G2282 8G2283 8G2284 8G2285 8G2286 8G8010 8G8020 8H1150 8H1150S 8H1180S 8H1183S 8H1184S 8H1280 8H1307 8H1315 8H1327 8H1394 8H1498 8H1499 8H1504 8H1510 8H1512 8H1520 8H1522 8H1530 8H1532 8H2010 8H2100 8H2131 8H2132 8H2142 8H2144 8H2184 8H2190 8H2300 8H2310 8H2314 8H2315 WASHER 7/8” AXLE S
SECTION 5 - PART NUMBERS & DESCRIPTIONS 8K7035 8K8000 8K8010 8K8020 8K8030 8K8030A 8K8060B 8K8067 8K8068A 8K8068B 8K8070A 8K8070B 8K8074 8K8075A 8K8080A 8K8088 8K8090 8K8090A 8K8092 8K8095 8K8095A 8K8105A 8K8200 8K8210 8K9102 8K9220 8K9230 8L0258 8N3018 8N3028 8N3035 8N3048 8N3060 8N3070 8N3084 8N3096 8N3124 8N3136 8N3150 8N3156 8N3160 8N3180 8N3204 8N3216 8N3228 8N3252 8N3276 8N3288 8N3312 8N3330 8N3348 8N3360 8N3390 8N3432 8N3462 8N3534 8N3570 8R6901 8R6902 8R6911 8R6913 8R6914 8R6915 8R6917 11L X 15 10P
SECTION 5 - PART NUMBERS & DESCRIPTIONS 8X0068 8X0069 8X0070 8X0071 8X0072 8X0073 8X0074 8X0075 8X0076 8X0077 8X0078 8X0080 8X0082 8X0083 8X0084 8X0087 8X0090 8X0091 8X0092 8X0093 8X0095 8X0096 8X0098 8X0099 8X0101 8X0102 8X0106 8X0107 8X0110 8X0111 8X0112 8X0113 8X0114 8X0115 8X0115A 8X0115B 8X0116 8X0117 8X0118 8X0118A 8X0119 8X0120 8X0121 8X0122 8X0123 8X0125 8X0130 8X0132 8X0133 8X0138 8X0139 8X0140 8X0141 8X0142 8X0143 8X0144 8X0145 8X0149 8X0150 8X0201 8X0202 8X0203 8X0204 8X0205 BOLT 1/2-13NC X 2-1/
SECTION 5 - PART NUMBERS & DESCRIPTIONS 8X0355 8X0361 8X0364 8X0366 8X0367 8X0368 8X0370 8X0380 8X0400 8X0402 8X0410 8X0414 8X0415 8X0418 8X0420 8X0422 8X0425 8X0428 8X0432 8X0440 8X0462 8X0500 8X0510 8X0520 8X0523 8X0605 8X0614 8X0632 8X0640 8X0665 8X0708 8X0710 8X0721 8X0725 8X0727 8X0728 8Z0070 8Z0075 8Z0079 8Z0087 8Z0101 8Z0110 8Z0114 8Z0115 8Z0130 8Z0276 8Z0278 8Z0342 8Z0344 8Z0346 8Z0800 8Z0805 8Z0810 8Z1000 8Z1111 WASHER 1-1/2”IDX2.25”X10GA PLN WASHER 1-3/4”ID X2.5”X10GA PLN WASHER 2-1/2”IDX3.
History of Summers Manufacturing Co., Inc. 1965 – Summers Manufacturing is founded by Harley Summers, who purchases patent rights for Goebel truck and pickup hoists from the Goebel Brothers of Lehr, ND. These hoists, produced in Harley Summers’ blacksmith shop the first year, were distributed nationwide by a Cincinnati, Ohio, dealer. With increasing sales, the company soon outgrows the small shop. Summers wins the Herman harrow contract, beginning the company’s Herman culti-harrow line.
Mounted Harrows Superharrow Plus & Superharrow 2650 Rolling Choppers Rolling Baskets Supercoulter Plus Superrollers Hydraulic Fold Coil Packer & Hydraulic Fold Rolling Chopper Diamond Disk & 2510 DT Superchisel Coulter-Chisel Disk-Chisel Model 700 Rock Picker Ultra & Ultimate NT Supersprayer To find a dealer near you check out our website - www.summersmfg.com or call us at: 1 (800) 732-4347 SUMMERS Manufacturing Company, Inc.
