Instruction Manual

8-11
SECTION 8 – PARTS
DRAWBAR CENTERS AND WINGS
Ref. Part No.
1-5 See Chart Page 8-5 - 16’ Hitch
See Chart Page 8-7 - 20’ Hitch
6 8D0620 - Knuckle Cast w/Zerks 6x4 Drawbar
7 Trans. Whl Asmbly - See Page 8-12
8 Hub Asmbly - See Page 8-21
9 8D6351 - Spindle w/Plate Wing for 611 Hub
8D6356 - Spindle w/611 Hub Wing
8D3850 - Spindle w/Plate Wing for 614 Hub (opt.)
8D3855 - Spindle w/614 Hub Wing (opt.)
10 7D6156 - Flat 1/2x7 - 8" w/Holes
11 8D6342 - Drop Axle Wing 3/4x10-9" w/Hrdw
12 8D0327 - Cable Pull Bracket HD (For 4x6)
13 8C2280 - Jack Attachment Bracket
14 8D8522 - 5000 LB Jack 15" Lift 5/8" Pin
15 8X0721 - Zerk 5/16-24 NF
16 8D1650 - Pin 1-3/4x9-3/4"
17 8D0750 - Pin 1-1/4CRx9-1/2" (1"-8NC) ZPL
18 8D0490 - Pin 1-1/4CRx7-1/2" (1"-8NC) ZPL
19 8D0302 - Pin 1-3/16x7-1/4" 7/16" Hole
20 8D1615 - Pin 1-3/16x9-1/2" 80 & After
21 8D1236 - Pin 1-1/4x9-1/2" (6"X4") HWNG
22 Cables & Pins - See Page 8-5 or 8-9
23 8X0414 - Cotter Pin 1/4x2"
24 8D9110 - Hair Pin Clip
25 8D0330 - U-Bolt 5/8x6-1/16x5-5/8" Sq
26 8D0340 - U-Bolt 3/4x4x7-3/4" Sq
27 8X0041 - Bolt 7/16-14NCx3"
28 8X0044 - Bolt 7/16-14NCx3-1/2"
29 8X0086 - Bolt 5/8-11NCx1-1/4"
30 8X0093 - Bolt 5/8-11NCx2"
31 8X0099 - Bolt 5/8-11x6" w/2.75" Thread
32 8X0234 - Nut Ny-Lock 7/16"-14NC
33 8X0250 - Nut Hex 5/8"-11NC
34 8X0260 - Nut Hex 3/4"-10NC
35 8X0304 - Lockwasher 5/8”
36 8X0306 - Lockwasher 3/4”
37 8D8521L - Jack Spool
38 8X0278 - 1” NC Lock Jam Nut
39 8X0316 - 1” Flat Washer
40 8D0112 - Cable Guide 112 Harrow
41 8D0110 - Flat 112' Cable Guide
42 8W0250 - ADD Drawbar PL w/Clevis
43 8W0115 - ADD Drawbar PL Free 1.5*
44 8W0200 - ADD Drawbar PL Wing Tube
45 8X0107 - Bolt 3/4-10NC x 2”
46 8X0112 - Bolt 3/4-10NC x 2-1/4”
47 8X0114 - Bolt 3/4-10NC x 3”
Ref. Part No.