Version: V1.
Dear Valued Customer, SUMERAIN would like to take this opportunity to thank you for purchasing SUMERAIN products. It is our sincere hope that you are completely satisfied with your new purchase. All SUMERAIN products are carefully engineered, and factory tested to provide long trouble-free use under normal conditions. This product is easy to install using basic tools and our easy to follow illustrated instructions.
VERSION: 140320.15.3 This product has been manufactured and tested to the highest quality standards by SUMERAIN sanitary Inc("SUMERAIN").This warranty is limited to SUMERAIN products which are purchased by a consumer in the China after Jan 1,2010 and installed in China or the state which has SUMERAIN technical support department locally.(visit http://www.sumerain.com/en/supportcenter.asp for review the state list of SUMERAIN technical support department).
Faucet type Shower System Feature Concealed shower faucet Theme Modern, Contemporary Mounting type Wall mount Number of Handles One Handles Material Metal Handle style Lever Shower Arm Reach 154mm [6-1/6 Inch] Showerhead Width 195mm [7-11/16 Inch] Showerhead Length 195mm [7-11/16 Inch] Valve Type Φ 40 Ceramic Cartridge Faucet Body Material Brass Escutcheon Material Brass Diverter included Yes Diverter location Rough-in Valve Showerhead Type Rain shower Showerhead shape Ul
FRONT VIEW OF SHOWER
SIDE VIEW OF SHOWER
1. BEFORE PROCEEDING WARNING: Read all the instructions completely before proceeding.SUMERAIN recommends calling a professional if you are uncertain about installing this product!, this product should be installed in accordance with all local and state plumbing and building codes. 2. SHUT OFF WATER SUPPLY Locate water supply inlets and shut off the water supply valves. These are usually found near the water meter.
4. PLANNING AND INSTALLATION INSTRUCTIONS Attentions: The shower has to be installed, rinsed and checked in compliance with the applicable regulations in order to guarantee proper shower function! The dimensions of the shower set-up must be individually. Operating pressure at the control valve: Max. 1Mpa. Recommended operating pressure: 3 bar pressure. Hot water temperature: Max 60 degree centigrade (140 Fahrenheit). 5. CONCEALED BOX ASSEMBLY INSTALLATION 5.
5.2 Secure the concealed box assembly to the mounting rack with screws and anchor. 6. VALVE TRIM INSTALLATION 6.1 Turn on your shut-off valve for cleaning the hot and cold water supply pipe before connect to the valve body, allow the water flush 3~5 minutes to flush out dirt and debris. Shut off the water supply again after finish.
6.2 Apply Teflon tape on the thread of pipe inlet and then connect to valve inlet with elbow [hot left, cold right].
6.3 Remove the valve sleeve by Phillips screwdriver. Turn on hold and cold water supply and check all connection for leaks Please shut off your hot and cold water supply again if no leaking. 6.4 Done the finish wall and drill proper window for maintain if needs in the future.
6.5 Drill the mounting holes exactly according to mixer valve and elbow position, done the finish wall. Cut the plaster shield around the finish wall surface and seal the wall around the plaster shield with waterproof sealant WARNING: Failure to seal the wall can lead to possible water damage.
6.5 Remove the valve sleeve by Phillips screwdriver and hold the screw for next step (fastening battery box). 6.6 Attach the escutcheon over the valve body.
6.7 Seal the wall around the plaster shield with waterproof sealant 6.8 Attach handle onto the valve stem and tighten set screws by the Allen wrench that is provided. Please don’t over tighten. Done the same procedure on diverter knob. Finally press-in the screw cover.
6.9 Valve trim install finish. 7. SHOWERHEAD INSTALLATION 7.1 Attach Shower arm escutcheon to the shower arm and apply Teflon tape on the thread of shower arm, Secure the shower arm into the pipe elbow inside the wall by rotating clockwise. Standard thread of Shower arm inlet: NPT1/2 (US, CA) G1/2” [1/2 BSPP] (UK, Europe etc.
7.
7.3 Put the screen washer into the connector of showerhead and secure the showerhead on the shower head arm by hand rotating clockwise. Missing the screen washer might lead to shower invalid. 8. HAND SHOWER INSTALLATION 8.1 Apply Teflon tape on the thread of nipple and screw the thread into the pipe elbow inside the wall.
8.2 Dock the shower holder assembly to nipple. 8.3 Secure shower holder to nipple with set screw by Allen Key.
8.4. Connect the hand shower to the elbow with flexible hose. 9. INSPECTION 9.1 Turn on hold and cold water supply and check all connection for ensuring no leaking anywhere. 10. FUNCTION INSPECTION 10.1 Turn on the handle, the water outflow from the showerhead. 10.2 Switch the diverter Knob, the water will rush from the hand shower.
Modern lavatory faucets, kitchen faucets, and showers consist of very different materials to comply with the needs of the market with regard to design and functionality. To avoid damage and returns, it is necessary to consider certain criteria when cleaning.
