SuiRui Room KIT Installation Guide
What is in the box 1 2 4 5 7 8 9 10 11 12 1.SuiRui Room Kit *1 2.Meeting Control Pad *1 3.Power Adapter for Meeting Control Pad*1 4.HDMI Cable (2 Meters) *2 5.Network Cable (2 Meters) *1 6.Power Adapter for the kit *1 7.Left Vertical Beam *1 8.Right Vertical Beam *1 9.Horizontal Beam *2 10.Vertical Beam Extension *2 11.Gasket *6 12.
Exterior illustration HDMI out Install DC in support pallet USB3.
Mount Suirui Room Kit on TV Note: The brackets are designed to support TV/Monitors between the size of 50 inch ~ 75inch. For those VESA mount has out of range ( 150mm to 600mm ) distance between. Top mount instruction 1.Remove the two vertical beams from VESA bracket , symmetrically install the two "horizontal beams" (make sure the bolt on beams facing outwards) into the holes on the TV VESA, put vertical beams (used to stabilize TV) and horizontal beams on t op of each other.
3. Install SuiRui Room Kit, follow the instructions in following Figures Manually adjust the parts in the red circle which are shown in the following figure Make sure the left and right parts are aligned to each other Clamping part Latch position 4.
Bottom mount instruction 1.Remove the two vertical beams from VESA bracket , symmetrically install the two "horizontal beams" (make sure the bolt on these beams facing outwards) into the holes on the TV VESA, put vertical beams (used to stabilize TV) and horizontal beams on top of each other. and then use screws to secure them (a total of 4 bolts). Note: The two horizontal beams has to be installed symmetrically. 2.
3.Install SuiRui Room Kit. Manually adjust the parts in the red circle which are shown in the following figure Make sure the left and right parts are aligned to each other Clamping part Latch position 4.
Note: There could be two special scenarios during installation process. A.Notice that: you will not need horizontal beam if the studs distance equals 600mm. B.If the size of the TV exceeds the length of the "vertical beam assembly", it is necessary to install vertical beam extension below the "vertical beam assembly". Connect Cables Normally, you will only have to connect four cables to start a dual screen meeting.
Connect power Network connect cable adapter Connect TV with HDMI cable adapter First time start SUIRUI Room Kit You only need to complete the following setting when you first time start Suirui Kit. You do not need to repeat these steps once the device is set up. 1.1 Turn on/off 1.1.1 Press power button to start。 1.1.2 Press power button again to shut down。 1.2 Connect internet with cable 1.2.1 Connect to a network with DHCP enabled (See 4.
1.4 Pairing the control pad and SuiRui Room Kit 1.4.1 Once connect to Internet, there will be a pairing code on TV. 1.4.2 Open the Zoom Room App on your control pad, and type in the pairing code to finish pairing. * If your SuiRui Room Kit used cable to connect internet, make sure your control pad connects to same network as your SuiRui Room Kit does.
1.5 Setting up your meeting rooms 1.5.1 Log in your Zoom Room account. 1.5.2 Set up and choose your meeting room. 1.5.3 Congratulations! You are now finishing the set ups. You can now start enjoying your meeting! FCC Notice: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.
IC Statement： English version: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’ s licenceexempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
