Step 1:Use 6 screws 9#, gaskets and caps to connect 2 part H2 with part #C/J1/C1 as shown in ① to form a front side wall panel. Step 2: Place the assembled front side wall panel (C/J1/C1) on the bottom frame(A1), using 5 screws 1# and gaskets to fix.
Si deVi ew X2 X4
Step 1: Place part #J1/C/J on the bottom frame (A6/A4), using 7 screws 1# and gaskets to fix. Step 2: Use 2 screws 9# and gaskets to install 2 part#（H5+H6）with part#C & J1, then put on the plastic caps as shown in ①. Step 3: Use 2 screws 9# and gaskets to install 2 part#（H5+H6）with part#J1 & C, then put on the plastic caps as shown in ③. Step 4: Use 4 screws 9# and gaskets to install 2 part#（H5+H6）with 2 part#J, then put on the plastic caps as shown in ⑤.
Step 1: Use 7 screws 1# and gaskets to fix 2 part#J on the bottom frame(A5 & A6). Step 2: Use 6 screws 9# and gaskets to fix 2 part#J with 2 part#(H5+H6), then put on the plastic caps to form a whole side wall as shown in ①②. Repeat the above procedures to assemble another side wall. Step 3: Use 13 screws 1# and gaskets to fix 4 part#J on the bottom frame(A4 & A3). Step 4: Use 10 screws 9# and gaskets to fix 4 part#J with 2 part#(H3+H4), then put on the plastic caps to form a whole back wall as shown in ①②.
Step1: Connect part #B1 and part #B2, insert part #B7 & B8 on the inside of part #B1/B2 with 6 screws 12# and gaskets as shown in ①. Step2: Connect part #B3 and part #B4, insert part #B7 on the inside of part #B3/B4 with 6 screws 12# and gaskets as shown in ②. Step3: Connect part #B5 and part #B6, insert part #B7 on the inside of part #B5/B6 with 6 screws 12# and gaskets as shown in ③. Repeat the above procedures to assemble another top beam.
Encl osewi t hpar t#B5/ B3,par t#B4/ B6,par t#B5/ B2,par t#B1/ B6,accor di ngt ot hefigur e abov e,andt hepar t #Bconnect st hef ourcor ner s,t henfixedwi t h16scr ews12#andgasket s asshowni n①②. Fi x2par t#C4onpar t#B1,par t#B2by4scr ews9#,gasket sasshowni n③④. soi nst al lt het opf r ameoneachwal lsepar at el y.
Pl acet heassembl edbeam ( B1, B2,B3, B4, B5, B6) ont heupperendoft hewal lpanel ,andf i xwi t h 59scr ews1#andgasket sasshowni n①②. Fi xt heupperendoft hepar t#C1/C2wi t h par t#B1andpar t #C4byusi ngscr ews3#,t he nut sandgasket sar eont hebacksi deasshown i n③④.
Assemble the part#G2 to the one side of part#K4 with 4 screws 2# gaskets and nuts. Assemble the part#G1 to the one side of part#K1 with 4 screws 2# gaskets and nuts.
The roof panel K1/K4 is fixed with top frame D1/D2 by using screws 2#,gaskets and nuts as shown in ③,then fix with screw 1# and gaskets to side top beam as shown in ④.
14
F2 Step1:Install the part #F: Insert part #Z into the top panel groove, use 4 screws 11#,gaskets and nuts to fix part#F2 and part #F on the roof top.(part #F should cover on part#F2) as shown in ②. 15 Step2:Use 4 screws 3#,gaskets and nuts to fix the 2 sides of part #F with part #K1/K4 and part #D1/D2 as shown in ①.
Step1: Use 14 screws 2# gaskets and nuts to fix part #G3 and part#G4 on the cornice of top roof. Step2: Use 4 screws 2#,gaskets and nuts to cover part #G7 on the connection of part #G3 and part#G4 as shown in ③. Repeat the above producers to assemble the another side.
17
18
19
