Use and Care Manual

ManualsBrandsSudzendf ManualsMetal Sheds6 ft. W x 4 ft. D Outdoor Metal Storage Shed with Sliding Doors and Padlock (24 sq. ft.)

Metal Garden Shed

OWNER'S MANUAL

Instructions for Assembly

Requires two people and takes 1-2 hours for lnstallation.

Quick & Easy Assembly

Ridge Reinforced Walls

Available in Various Sizes

SNSD-F2-2-H154

Summary of content (15 pages)

PAGE 1
Metal Garden Shed OWNER'S MANUAL Instructions for Assembly SNSD-F2-2-H154 Requires two people and takes 1-2 hours for lnstallation.
PAGE 2
BEFORE YOU START Owner's Manual Prior to installation, it is important that you contact your local government authority to determine if building approval is required. Study and understand this owner's manual. Important information and helpful tips will make your construction easier and more enjoyable. Assembly instructions Instructions are supplied in this manual and contain all appropriate information for your building model. Review all instructions before you begin.
PAGE 3
PLAN AHEAD Site Selection l Avoid overhanging trees as much as possible as leaves will make regular cleaning necessary and broken branches are a potential hazard. l Small trees,bushes or fences nearby can be helpful,acting as a wind break. Site Preparation The site must be prepared so that the base of the shed is level all round and checking with a spirit level is required. The base can be constructed by treated timber or concrete,in order to stop the moisture getting into the shed.
PAGE 4
NO. PART 1 Qty. NO. 1 15 1 981mm 1 6 20 411mm 608mm 3R 4 17 1070mm 3L 2 1196mm 1070mm 2 Qty.
PAGE 5
NO. PART P1 Qty. NO. PART Qty. 4 1560mm P2 4 1560mm P3 2 1 D1 1560mm P6 2 1550X415mm 1560mm P4 2 1196mm P5 2 1196mm P7 1 1 D2 1196mm 1550X415mm NO. PART Qty.
PAGE 6
GC 15 P4 17 GC P5 P7 17 17 P5 21L GC P4 B1 17 12L 15 B1 GC GF B1 21R B1 GF 12R 9 10L P2 P1 10R P1 P3 P2 P1 P1 1 7 4L 3L 4R 5 11 20 P6 20 P3 P2 20 25L 20 D1 P6 25R 20 D2 P2 8 20 GB 2 3R 6
PAGE 7
NO. PART Qty. 4L 1 4R 1 4L F1 4R NO. PART Qty. 1 1 2 1 F1 4L 4R 1 F1 2 NO. PART Qty.
PAGE 8
NO. PART 5 Qty. 1 F1 F1 5 1、When diagonal measurements are equal,the frame is square. 2、The Floor Frame must be BOTH square AND level or the holes will not line up properly. NO. PART Qty.
PAGE 9
NO. PART Qty. 1 P2 Ⅰ Ⅰ P2 5 S3 S3 F1 Ⅱ Ⅱ F2 NO. PART Qty. P1 1 P1 S3 5 F1 NO. PART Qty.
PAGE 10
NO. PART Qty. 1 P6 P6 S3 5 F1 NO. PART Qty. 1 P2 Ⅰ P2 S3 S3 F1 Ⅱ F2 NO. 5 PART Qty.
PAGE 11
NO. PART Qty. Ⅰ 1 P2 P2 S3 4R F2 NO. PART S3 F1 Ⅱ 4L Qty. 10L 1 10R 1 10R S3 F1 10L F1 4R 4L NO. PART Qty.
PAGE 12
NO. Qty. PART 7 1 8 1 G2 4 6 1 6 7 7&8 S3 F1 8 7&8 8 NO. 7 PART G2 6 Qty. P1 2 P3 2 25L 1 25R 1 P1 P3 P1 S3 F1 P3 25L F1 S3 S3 25R F2 Qty. NO. 12L 1 B1 4 12R 1 GF 2 NO. PART PART Qty.
PAGE 13
NO. PART Qty. 21L 1 21R 1 12L 21L S3 12R F2 F1 S3 21R S3 F2 NO. PART Qty. P4 P4 2 P5 2 P7 1 P5 P7 F1 P5 P4 S3 NO. PART Qty.
PAGE 14
NO. PART Qty. D1 1 D2 1 GB 2 GB F2 D1&D2 x2 NO. PART 20 6 F1 20 Qty. F2 S3 20 20 D1&D2 S3 x2 F2 NO. GD PART Qty.
PAGE 15
7&8 G2 F3 D1 -15- D2