U N D E R C O U N T E R R E F R I G E R AT I O N I NSTALLATION I NSTRUCTIONS
U N D E R C O U N T E R I N S TA L L AT I O N The importance of the installation of the Sub-Zero Undercounter unit cannot be overemphasized. Installation should be done by a qualified installer. CONTENTS Installation Recommendations 3 Installation Instructions 4 Door Panel Installation 7 Installation Checklist 10 Service Information 11 Features and specifications indicated herein and on the website are subject to change at any time without notice. Check our website, subzero.
U N D E R C O U N T E R I N S TA L L A T I O N I N S T R U C T I O N S I N S TA L L AT I O N R E C O M M E N D AT I O N S S I T E P R E PA R AT I O N Make sure that the finished rough opening where the Undercounter unit is to be installed is properly prepared. Refer to the Installation Specifications illustration for rough opening dimensions, door swing clearance and location of electrical and plumbing (Model UC-24C).
U N D E R C O U N T E R I N S TA L L AT I O N I N S T R U C T I O N S OPTIONAL COMPONENTS Optional installation components are available through your Sub-Zero dealer. For questions relative to the installation, call Sub-Zero at 800-222-7820. ELECTRICAL R E Q U I R E M E N T S PLUMBING R E Q U I R E M E N T S A 115 V AC, 60 Hz, 15 amp circuit breaker and electrical supply are required. A separate circuit, servicing only this appliance, is required. Model UC-24C comes with an automatic ice maker.
U N D E R C O U N T E R I N S TA L L A T I O N I N S T R U C T I O N S U N PAC K I N G A N D M OV I N G POSITION T H E U N I T Uncrate the unit and remove its wood base. Remove all packing materials and tape. IMPORTANT NOTE: If the Undercounter unit has been laid on its back or side, you must allow the unit to stand upright for a minimum of 24 hours before connecting power.
U N D E R C O U N T E R I N S TA L L AT I O N I N S T R U C T I O N S A N T I - T I P B R AC K E T I N S T A L L A T I O N To prevent the unit from tipping forward and provide a stable installation, the unit must be secured in place with the anti-tip bracket. LEVEL T H E U N I T Using an adjustable wrench or pliers, turn each of the four leveling legs clockwise to raise the unit and counterclockwise to lower the unit. For the location of the leveling legs, refer to the illustration below.
U N D E R C O U N T E R I N S TA L L A T I O N I N S T R U C T I O N S D O O R PA N E L I N S TA L L A T I O N MODELS UC-24R AND UC-24C GLASS DOOR MODEL UC-24B Models UC-24R and UC-24C can be fitted with a custom overlay or stainless steel door front panel. A classic stainless steel door panel with tubular handle is available as a sales accessory. Installation of the stainless steel panel will be required.
U N D E R C O U N T E R I N S TA L L AT I O N I N S T R U C T I O N S OV E R L AY PA N E L I N S T A L L A T I O N GLASS DOOR MODEL UC-24B/O Inspect the door panel for the minimum 5/8" (16) thickness, the finished inside edge and the weight limit. Decide if the handle will be attached through the glass door frame or just through the decorative door panel. If it is just through the door panel, the handle must be attached first.
U N D E R C O U N T E R I N S TA L L A T I O N I N S T R U C T I O N S OV E R L AY PA N E L I N S T A L L A T I O N MODELS UC-24R AND UC-24C The Model UC-24B glass door is made with a sealed double-wall tempered glass core. The drill must not contact this core when drilling. Be sure the hole is centered on the small groove in the front of the door frame and the drill passes squarely through the frame. If you are inexperienced with drilling, fasten the handle from the rear of the door panel only.
U N D E R C O U N T E R I N S TA L L AT I O N I N S T R U C T I O N S OV E R L AY PA N E L I N S T A L L A T I O N HINGE A D J U S T M E N T MODELS UC-24R AND UC-24C IMPORTANT NOTE: The Undercounter unit should be properly leveled in position before door hinge adjustments are made. Before attaching the panel to the door, remove the outer screws from each of the two mounting positions along the hinge side of the door.
S E RV I C E I N F O R M A T I O N S E RV I C E I N F O R M A T I O N I N S TA L L A T I O N C H E C K L I S T Has all packing material been removed? Turn the unit on first, is the unit operating properly? If not, is it plugged in? Is the control turned on? Has the unit been secured in place with the anti-tip bracket? Is the unit level? Are all leveling legs making contact with the floor? Is the power cord plugged into a properly grounded 3-prong outlet, which has been installed in accordance with all app
S U B - Z E R O F R E E Z E R C O M PA N Y, I N C . 7 0 0 1 1 0 3 R E V- B 1 / 2007 P. O . B O X 4 4 1 3 0 MADISON, WI 53744-4130 800-222-7820 S U B Z E RO.
