INSTALLATION GUIDE Undercounter Refrigeration
Contents Important Note Undercounter Refrigeration . . . . . . . . . . . . . . . . . . . . . 3 To ensure the safe and efficient installation of Sub-Zero equipment, please take note of the following types of highlighted information throughout this guide: Undercounter Specifications . . . . . . . . . . . . . . . . . . . . 4 Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Undercounter Installation . . . . . . . . . . . . . . . . . . . . . . 7 Service Information . . . . . . .
Undercounter Refrigeration 3 subzero.com/specs Sub-Zero Undercounter Refrigeration IMPORTANT NOTE: The importance of the installation of the Sub-Zero undercounter unit cannot be overemphasized. Installation should be done by a qualified installer. RATING PLATE Before you begin the installation process, it is recommended that you read this entire installation guide. There are key details that you should take special care to observe during the installation.
Undercounter Specifications 4 Undercounter Models OVERALL DIMENSIONS 23 7/8" (606) OPENING DIMENSIONS 24" (610) TOP VIEW 24" (610) OPENING DEPTH 34" (864) 4" (102) 24" (610) OPENING DEPTH 341/2" (876) OPENING HEIGHT 24" (610) OPENING WIDTH 25 3/8" (645) SIDE VIEW 1 3/4" (44) SPECIFICATIONS Shipping Weight lbs (kg) All Models 130 (59) FRONT VIEW
Site Preparation 5 subzero.com/specs Before You Start Make sure the opening dimensions, door clearance, electrical service and plumbing are correct for the model you are about to install. Refer to specifications on the following pages. TOOLS AND MATERIALS REQUIRED IMPORTANT NOTE: To operate properly, the door must open a minimum of 90°. Use a minimum 3" (76) filler in corner installations to assure a 90° door opening. Allow enough clearance in front of the unit for full door swing.
Site Preparation 6 Electrical Requirements Plumbing Requirements The electrical supply should be located within the shaded area shown in the illustration below. Follow the National Electrical Code and local codes and ordinances when installing the receptacle. A separate circuit, servicing only this appliance is required. MODEL UC-24CI IMPORTANT NOTE: The electrical outlet must be placed so the grounding prong is to the right of the thinner blades. The outlet must be flush with the back wall.
Undercounter Installation 7 subzero.com/specs Unpack the Unit Before moving the undercounter unit into position, make sure all opening dimensions, electrical and plumbing requirements are complete and accurate. IMPORTANT NOTE: The floor under the undercounter unit must be at the same level as the surrounding finished floor to allow for removal of the unit for servicing. Use an appliance dolly to move the undercounter unit near the installation opening.
Undercounter Installation 8 Installation IMPORTANT NOTE: If the undercounter unit has been laid on its back or side, you must allow the unit to stand upright for a minimum of 24 hours before connecting power. With the undercounter unit near the installation opening, plug the power cord into the electrical outlet. With power applied to the unit, check for lighting and cooling.
Undercounter Installation 9 subzero.com/specs Door Panel MODELS UC-24R AND UC-24C(I) Panel Specifications Models UC-24R and UC-24C(I) can be fitted with a custom overlay or stainless steel door front panel. A stainless steel door panel with tubular or pro handle is available as a sales accessory. Installation of the stainless steel panel will be required. OVERLAY PANEL For the overlay application, a decorative door panel and handle hardware must be provided.
Undercounter Installation 10 Overlay Panel Installation MODELS UC-24R AND UC-24C(I) Inspect the overlay door panel for minimum thickness and weight limit. Remove the two panel mounting brackets attached to the front of the door and set aside. Place the overlay panel lying face down on a protected surface to ensure that the front is not scratched or damaged. Position the plastic template (provided) flush with the lower edge of the door panel.
Undercounter Installation 11 subzero.com/specs Overlay Panel Installation BEVERAGE CENTER MODEL UC-24BG Inspect the overlay door panel for minimum thickness, weight limit and finished inside edges. Decide if the handle will be attached through the glass door frame or just through the decorative door panel. If it is just through the door panel, the handle must be attached first.
Undercounter Installation Overlay Panel Installation The model UC-24BG glass door is made with a sealed, double-wall tempered glass core. The drill must not contact this core when drilling. Be sure the hole is centered on the small groove in the front of the door frame and the drill passes squarely through the frame. If you are inexperienced with drilling, fasten the handle from the rear of the door panel only. IMPORTANT NOTE: For model UC-24BG, install screws in all the mounting holes in the door frame.
Undercounter Installation 13 subzero.com/specs Installation Checklist To ensure a safe and proper installation, the following checklist should be completed by the installer to ensure that no part of the installation has been overlooked. Has all packing material been removed? Turn the unit on.
Service Information 14 Service Information If service is necessary, maintain the quality built into your undercounter unit by calling Sub-Zero factory certified service. For the name and number of Sub-Zero factory certified service nearest you, check the contact & support section of our website, subzero.com or call Sub-Zero customer care at 800-222-7820. When calling for service, you will need the model and serial numbers of your unit.
The information and images in this guide are the copyright property of Sub-Zero, Inc. Neither this guide nor any information or images contained herein may be copied or used in whole or in part without the express written permission of Sub-Zero, Inc. ©Sub-Zero, Inc. all rights reserved. Wolf, Wolf & Design, Wolf Gourmet, W & Design and the color red as applied to knobs are registered trademarks and service marks of Wolf Appliance, Inc.
SUB-ZERO, INC. P. O. BOX 44848 MADISON, WI 53744 7023606 REV-A 12/2011 SUBZERO.COM 800.222.
