MODEL 315W WINE COOLER I NSTALLATION & O PERATION
CONTENTS Model 315W Features 4 Model 315W Installation 5 Installation Checklist 13 Model 315W Operation 14 Troubleshooting Guide 17 Service Information 18 Sub-Zero Warranty 19 Features and specifications indicated herein and on the website are subject to change at any time without notice. Check our website, subzero.com, for the most up-to-date specifications. As you follow these instructions, you will notice WARNING and CAUTION symbols.
S U B - Z E R O M O D E L 3 1 5 W I N S TA L L AT I O N A N D O P E R AT I O N T H A N K YO U Congratulations on the purchase of your Sub-Zero Model 315W wine cooler. This unit is designed and manufactured in the Sub-Zero tradition of superior quality and reliability. The importance of the installation of the Model 315W wine cooler cannot be overemphasized. Installation should be done by a qualified installer.
S U B - Z E R O M O D E L 3 1 5 W F E AT U R E S M O D E L 3 1 5 W F E AT U R E S WA R R A N T Y Sub-Zero products are covered by a two, five and twelve year residential warranty (exclusions apply). See warranty details at the end of this guide. Undercounter wine cooler with 26 (750 ml) bottle capacity Full-view glass door with UV resistant glass protection Overlay and stainless steel design options High altitude glass door Ideal humidity and temperature range of 45˚F (7˚C) to 55˚F (13˚C).
S U B - Z E R O M O D E L 3 1 5 W I N S TA L L AT I O N I N S TA L L AT I O N S P E C I F I C A T I O N S MODEL 315W DIMENSIONS Overall Width 15 1/8" (384) Overall Height 34 1/16" (865) Overall Depth – 315W/S 23 5/32" (588) Overall Depth – 315W/O 22 3/8" (568) Rough Opening Width 15 1/4" (387) Rough Opening Height 34 1/2" (876) Minimum Height Required (levelers in) 34 1/16" (865) Rough Opening Depth 24" (610) Dimensions may vary +_ 1/8" (3).
S U B - Z E R O M O D E L 3 1 5 W I N S TA L L AT I O N I N S TA L L AT I O N S P E C I F I C A T I O N S AREA REQUIREMENTS Before moving the unit into place, be sure that the rough opening dimensions, electrical location, and minimum door clearances are accurate. Refer to the illustration below. Also Refer to page 5 for overall dimensions. Be sure your electrician and cabinet installer have this information before finishing work is completed. Wine bottles are heavy.
S U B - Z E R O M O D E L 3 1 5 W I N S TA L L AT I O N ELECTRICAL R E Q U I R E M E N T S K I C K P L AT E A I R F L O W A 115 V AC, 60 Hz, 15 amp circuit breaker and electrical supply are required. A separate circuit is required for each unit. The wine cooler uses a fan to take in room air through vents in the left side of the kickplate, and discharges warm air through vents in the right side. These vents must be kept clear of obstructions or decorative panels.
S U B - Z E R O M O D E L 3 1 5 W I N S TA L L AT I O N BLOCKING F O R S A F E T Y To prevent the unit from tipping forward if multiple loaded bottle racks are pulled out at one time, and to provide a stable installation, the unit must be secured in place with an anti-tip device. A metal antip-tip bracket and screws are provided with the unit. Attach the anti-tip bracket to the top of the unit, opposite the hinge side.
S U B - Z E R O M O D E L 3 1 5 W I N S TA L L AT I O N K I C K P L AT E I N S T A L L A T I O N PA N E L C O N S I D E R A T I O N S Once the Model 315W is in place, you can install the kickplate. There is some adjustment to the mounting assembly so that the kickplate will fit flush with the surrounding area. Be sure that nothing obstructs the vents of the kickplate. Refer to the illustration below. The Model 315W offers two door panel design alternatives; stainless steel (/S) or overlay (/O).
S U B - Z E R O M O D E L 3 1 5 W I N S TA L L AT I O N OV E R L AY P A N E L S O V E R L AY P A N E L S P E C I F I C A T I O N S Door Panel Width – 1/8" (3) reveal* 15" (381) Door Panel Height – 7/16" (11) reveal** 4" (102) toe space 30 1/16" (764) PA N E L DESIGN 2 1/4" (57) min Width of Rails and Stiles 5/ 8" Door Panel Thickness Additional panel design information can be found in the Sub-Zero Design Guide. Check our website at subzero.com. Door Panel Weight (16) min 10 lbs (4.
S U B - Z E R O M O D E L 3 1 5 W I N S TA L L AT I O N OV E R L AY PA N E L I N S T A L L A T I O N A decorative panel is attached to the Model 315W door using #8 x 5/8" (16) square drive screws passing through the door frame from the rear, behind the gasket into the panel. The door panel is marked for screw locations by the use of 'tenon centers', which are temporarily inserted into the 1/4" (6) diameter holes in the front of the glass door frame. Refer to the illustration below.
S U B - Z E R O M O D E L 3 1 5 W I N S TA L L AT I O N OV E R L AY PA N E L I N S T A L L A T I O N IMPORTANT NOTE: Install screws in all the mounting holes in the door frame. The nature of the door panel with a narrow outer rim and no connecting center member requires the support provided by the glass door. PA N E L DESIGN Additional panel design information can be found in the Sub-Zero Design Guide. Check our website at subzero.com.
S U B - Z E R O M O D E L 3 1 5 W I N S TA L L AT I O N I N S TA L L AT I O N C H E C K L I S T IMPORTANT NOTE: To ensure a safe and proper installation, the following checklist should be completed by the installer to ensure that no part of the installation has been overlooked. Any questions or problems about the installation should be directed to your Sub-Zero dealer or the Sub-Zero Customer Service Department at 800-222-7820. You can also visit our website at subzero.com.
S U B - Z E R O M O D E L 3 1 5 W O P E R AT I O N USING YO U R W I N E C O O L E R Your wine cooler is extremely simple to use, just turn the control knob to the ON position. The Model 315W will automatically begin to cool and will continue to do so until the set temperature is reached. The Model 315W operates on this principal; the unit will run to achieve the set temperature. Run time will vary based upon the amount of usage, room temperature and amount of wine added.
S U B - Z E R O M O D E L 3 1 5 W O P E R AT I O N W I N E S H E LV E S Model 315W has roller-assembly shelves with a full three-quarter extension for easy access to wine bottles. Each wine shelf holds four (750 ml) bottles. An additional two (750 ml) bottles may be placed on the bottom stationary shelf for a total capacity of 26 bottles. Refer to the illustration below.
S U B - Z E R O M O D E L 3 1 5 W O P E R AT I O N CLEANING EXTERIOR CLEANING S I G N AT U R E POLISH Signature Polish is available from Signature Limited Laboratory, P. O. Box 13436, Dayton, Ohio 45413-0436, or call 877-376-5474 (toll free). To clean the classic stainless steel exterior of the Model 315W/S, use a soft, nonabrasive stainless steel cleaner like Signature Polish (see side note) and apply with a soft 100% lint-free cloth.
S U B - Z E R O T R O U B L E S H O OT I N G G U I D E T R O U B L E S H O OT I N G G U I D E P RO B L E M POSSIBLE CAUSE POSSIBLE SOLUTION Cabinet too warm Unit switched off Check temperature control Cabinet temperature changed Temperature control setting changed Check temperature setting Excessive operating time Dirty condenser Clean condenser Cabinet full of warm wine Unit must operate for up to 24 hours to cool warm wine Door gasket not sealing tightly Check gasket fit Thick frost on e
S E RV I C E I N F O R M A T I O N S E RV I C E I N F O R M A T I O N C O N TA C T I N F O R M AT I O N Sub-Zero Customer Service: 800-222-7820 Website: subzero.com If you do need service, be sure to have the model and serial number of your unit when you call. You’ll find these numbers on the model and serial number plate located on the underside of the top wall. For warranty purposes, you will also need the date of installation and the name of your Sub-Zero dealer.
S U B - Z E R O F R E E Z E R C O M PA N Y P R O D U C T S LIMITED WARRANTY RESIDENTIAL USE ONLY FULL FIVE YEAR SEALED SYSTEM WARRANTY LIMITED SIXTH THROUGH TWELFTH YEAR WARRANTY ON THE SEALED SYSTEM FULL TWO YEAR WARRANTY ON TOTAL PRODUCT* FULL FIVE YEAR SEALED SYSTEM WARRANTY For five years from the date of original installation, your Sub-Zero warranty covers all parts and labor to repair or replace any components that prove to be defective in materials or workmanship in the sealed system.
S U B - Z E R O F R E E Z E R C O M PA N Y, I N C . 17308001 8 / 2005 P. O . B O X 4 4 1 3 0 MADISON, WI 53744-4130 800-222-7820 S U B Z E RO.
