PRO 48 I NSTALLATION I NSTRUCTIONS
CONTENTS PRO 48 Installation Recommendations 3 PRO 48 Overall Dimensions 4 PRO 48 Installation Specifications 5 PRO 48 Installation Instructions 6 PRO 48 Installation Checklist 14 PRO 48 Service Information 15 Features and specifications indicated herein and on the website are subject to change at any time without notice. Check our website, subzero.com, for the most up-to-date specifications. As you follow these instructions, you will notice WARNING and CAUTION symbols.
P R O 4 8 I N S TA L L A T I O N R E C O M M E N D A T I O N S I N S TA L L AT I O N R E C O M M E N D AT I O N S The importance of the Sub-Zero PRO 48 installation cannot be overemphasized. The installation procedure should be completed by a qualified installer. Before you begin the installation process, it is recommended that you read this entire Installation Instructions book. There are key details that you should take special care to observe during the installation.
PRO 48 O V E R A L L D I M E N S I O N S OV E R A L L D I M E N S I O N S IMPORTANT NOTE: Model 648PROG features a glass door on the upper refrigerator compartment and Model 648PRO has a solid door. All overall dimensions and installation dimensions are identical for each of the PRO 48 units.
P R O 4 8 I N S TA L L A T I O N S P E C I F I C A T I O N S I N S TA L L AT I O N S P E C I F I C A T I O N S The PRO 48 can be used free-standing or installed as a standard or flush built-in application. For standard built-in installations, the face frame of the unit will extend 2" (51) beyond cabinetry. In flush built-in installations, the front of the face frame will be flush with surrounding cabinetry. IMPORTANT NOTE: To operate properly, doors must be able to open a minimum of 90˚.
P R O 4 8 I N S TA L L A T I O N I N S T R U C T I O N S ELECTRICAL R E Q U I R E M E N T S PLUMBING R E Q U I R E M E N T S A 115 V AC, 60 Hz, 15 amp circuit breaker and electrical supply are required. A separate circuit, servicing only this appliance, is required. Locate the electrical outlet within the shaded area indicated in the Installation Specifications illustration on the previous page. The PRO 48 has an automatic ice maker with an integrated water filtration system.
P R O 4 8 I N S TA L L A T I O N I N S T R U C T I O N S U N PA C K I N G T H E PRO 48 W AT E R F I L T E R B Y P A S S M O D E If you choose not to use the water filtration system, the system can be placed in water filter bypass mode by removing the water filter cartridge. In this mode, the water supplied to the ice maker will not be filtered and the electronically controlled water filter monitor will be deactivated. Lift the grille to access the water filter cartridge.
P R O 4 8 I N S TA L L A T I O N I N S T R U C T I O N S A N T I - T I P B R AC K E T I N S T A L L A T I O N W O O D F L O O R A P P L I C AT I O N S To prevent the PRO 48 from tipping forward and provide a stable installation, the unit must be secured in place with the anti-tip bracket shipped with the unit. IMPORTANT NOTE: Placement of the anti-tip bracket is critical to a stable installation.
P R O 4 8 I N S TA L L A T I O N I N S T R U C T I O N S C O N C R E T E F L O O R A P P L I C AT I O N S I N S TA L L C O N C R E T E W E D G E A N C H O R S Use the three 3/8" x 3 3/4" concrete wedge anchors, six # 12 x 2 1/2" wood screws and six # 12 flat washers provided. Be sure that the anchors and screws hold tight. Refer to the illustration below. 1) Drill a 3/8" (10) diameter hole any depth exceeding the minimum embedment.
P R O 4 8 I N S TA L L A T I O N I N S T R U C T I O N S M O V I N G T H E PRO 48 After you've completed the steps for unpacking the PRO 48 and have removed the grille and installed the anti-tip bracket, carefully move the unit onto an appliance dolly. When securing the unit on the appliance dolly, use the corner protectors retained from the packaging under the strapping to avoid damage to the stainless steel exterior. Also, secure the doors and drawers closed with the strapping.
P R O 4 8 I N S TA L L A T I O N I N S T R U C T I O N S DOOR A D J U S T M E N T Check to make sure that both doors are properly adjusted. If not, adjustments can be made to the cabinet and door hinges. IMPORTANT NOTE: Be sure the unit is properly leveled before doing any cabinet or door hinge adjustment. CABINET HINGE ADJUSTMENT DOOR HINGE ADJUSTMENT The door must be removed to adjust cabinet hinges.
Dimensions in parentheses are in millimeters unless otherwise specified.
P R O 4 8 I N S TA L L A T I O N C H E C K L I S T S I D E A N D T O P PA N E L S Accessory stainless steel side and top panels are available through your Sub-Zero dealer. Installation instructions are included with the panels. To obtain local dealer information, visit the Locator section of our website, subzero.com. 9 0 D E G R E E D O O R S TO P The doors of PRO 48 models open to 135 degrees. An optional 90˚ door stop kit is available through your Sub-Zero dealer.
P RO 4 8 S E RV I C E I N F O R M AT I O N S E RV I C E I N F O R M A T I O N If you need service, be sure to have the model and serial number when you call. You’ll find these numbers on the model and serial number plate located on the left side of the top freezer drawer compartment. Call your Sub-Zero authorized service center; contact your dealer or the Sub-Zero Customer Service Department, P. O. Box 44130, Madison, WI 53744-4130 or call 800-222-7820.
S U B - Z E R O F R E E Z E R C O M PA N Y, I N C . 3 7 5 8 5 9 9 R E V- B 10 / 2005 P. O . B O X 4 4 1 3 0 MADISON, WI 53744-4130 800-222-7820 S U B Z E RO.
