INTERNATIONAL DESIGN GUIDE
CONTENTS Built-In Refrigeration 4 Integrated Refrigeration 27 Wine Storage 46 Undercounter Refrigeration 63 Features and specifications indicated herein and on our website are subject to change at any time without notice. Check our website, subzero.com, for the most up-to-date specifications. IMPORTANT NOTE International models from the factory designed without a transformer require a 220/240 V AC, 50/60 Hz electrical supply, fused at the correct rating for the unit.
WELCOME TO SUB-ZERO We make the ultimate built-in, integrated and undercounter refrigerators, freezers and wine storage units. We offer more solutions to your daily design problems of trying to work the largest appliance into a home without being obtrusive. Placing refrigeration in the home is no longer a problem, but, rather, an opportunity to exercise your creativity. Sub-Zero has rethought traditional built-in refrigeration, a category it pioneered, with over 60 years of experience.
B U I LT- I N R E F R I G E R AT I O N Sub-Zero’s Built-In line offers you the most complete set of design options in built-in refrigeration for all of its models, from the beauty of the overlay models to the professional treatment of the wrapped stainless steel doors. Glass doors are available on our Models I601R, I611 and I650. They each come in a framed, overlay and stainless steel design. Model ICB648PROG also features a glass door in its classic stainless steel look.
B U I LT- I N R E F R I G E R AT I O N A L L R E F R I G E R AT O R | A L L F R E E Z E R These illustrations represent the full line of Sub-Zero Built-In models shown in the stainless steel design application with heavy-duty grille. Models ICB648PRO and ICB648PROG are available as built-in or free-standing units in classic stainless steel only. 914 mm 1854 mm For information regarding specific Built-In models, refer to the illustrations in this section.
B U I LT- I N F E AT U R E S Overlay models blend seamlessly into your overall room design and complement surrounding cabinetry. You add decorative hardware. Overlay models come with a panel grille that will accept decorative panel inserts. The new ice and water dispensing Models I685 and I695 are also available in the overlay application. ACCESSORIES Optional accessories are available through your Sub-Zero dealer.
MODEL I601R MODEL I601RG MODEL I601F A L L R E F R I G E R AT O R A L L R E F R I G E R AT O R WITH GLASS DOOR ALL FREEZER MODEL OPTIONS MODEL OPTIONS MODEL OPTIONS Overlay Design I601R/O Overlay Design I601RG/O Overlay Design I601F/O Classic Stainless Steel I601R/S Classic Stainless Steel I601RG/S Classic Stainless Steel I601F/S S P E C I F I C AT I O N S S P E C I F I C AT I O N S S P E C I F I C AT I O N S Overall Width 914 mm Overall Width 914 mm Overall Width 914 mm Overal
MODEL I611 MODEL I611G OVER-AND-UNDER OVER-AND-UNDER WITH GLASS DOOR All models are shown in the stainless steel design application.
MODEL I650 MODEL I650G OVER-AND-UNDER OVER-AND-UNDER WITH GLASS DOOR ACCESSORIES MODEL OPTIONS MODEL OPTIONS Overlay Design I650/O Overlay Design I650G/O Classic Stainless Steel I650/S Classic Stainless Steel I650G/S S P E C I F I C AT I O N S Optional accessories are available through your Sub-Zero dealer.
MODEL I661 MODEL I642 MODEL I685 S I D E - B Y- S I D E S I D E - B Y- S I D E S I D E - B Y- S I D E I C E | W AT E R D I S P E N S I N G MODEL OPTIONS MODEL OPTIONS MODEL OPTIONS Overlay Design I661/O Overlay Design I642/O Overlay Design I685/O Classic Stainless Steel I661/S Classic Stainless Steel I642/S Classic Stainless Steel I685/S S P E C I F I C AT I O N S S P E C I F I C AT I O N S S P E C I F I C AT I O N S Overall Width 914 mm Overall Width 1067 mm Overall Width 1067
MODEL I632 MODEL I695 S I D E - B Y- S I D E S I D E - B Y- S I D E I C E | W AT E R D I S P E N S I N G All models are shown in the stainless steel design application.
MODEL ICB648PRO MODEL ICB648PROG S I D E - B Y- S I D E B U I LT- I N O R F R E E - S TA N D I N G S I D E - B Y- S I D E WITH GLASS DOOR B U I LT- I N O R F R E E - S TA N D I N G S P E C I F I C AT I O N S S P E C I F I C AT I O N S Overall Width 1219 mm Overall Width 1219 mm Overall Height 2134 mm Overall Height 2134 mm Overall Depth 657 mm Overall Depth 657 mm Refrigerator Capacity 521 L Refrigerator Capacity 521 L Freezer Capacity 331 L Freezer Capacity 331 L Min Height Requir
PLANNING INFORMATION ELECTRICAL REQUIREMENTS Although the Sub-Zero Built-In line offers a wide range of designs and configurations, the basic planning considerations for all models have much in common. As you integrate Built-In models into your overall plan, review installation requirements for your particular model(s). The Installation Specifications illustrations provide planning information for all Built-In models— overlay and stainless steel.
OVERALL DIMENSIONS All Refrigerator | All Freezer Models A L L R E F R I G E R AT O R ALL FREEZER 1854 mm 1854 mm 1854 mm Model I601R All Refrigerator Model I601RG All Refrigerator with Glass Door Model I601F All Freezer 914 mm 914 mm 914 mm Model I601R Model I601RG Model I601F All Refrigerator All Refrigerator with Glass Door All Freezer Width 914 mm Width 914 mm Width 914 mm Height 1854 mm Height 1854 mm Height 1854 mm Depth 610 mm Depth 610 mm Depth 610 mm 610 mm Illustr
OVERALL DIMENSIONS Over-and-Under Refrigerator / Freezer Models OVER-AND-UNDER 2134 mm 2134 mm 2134 mm 2134 mm Model I611 Model I611G with Glass Door Model I650 Model I650G with Glass Door 762 mm Model I611 762 mm Model I611G 914 mm 914 mm Model I650 610 mm Model I650G with Glass Door with Glass Door Width 762 mm Width 762 mm Width 914 mm Width 914 mm Height 2134 mm Height 2134 mm Height 2134 mm Height 2134 mm Depth 610 mm Depth 610 mm Depth 610 mm Depth 610 mm Illus
OVERALL DIMENSIONS Side-by-Side Refrigerator | Freezer Models 2134 mm 914 mm Model I661 1067 mm 1067 mm Model I685 Model I642 1219 mm 1219 mm Model I632 610 mm Model I695 Ice | Water Dispensing Ice | Water Dispensing Width 914 mm Width 1067 mm Width 1067 mm Width 1219 mm Width 1219 mm Height 2134 mm Height 2134 mm Height 2134 mm Height 2134 mm Height 2134 mm Depth 610 mm Depth 610 mm Depth 610 mm Depth 610 mm Depth 610 mm Illustrations shown in stainless steel de
OVERALL DIMENSIONS PRO 48 Side-by-Side Refrigerator | Freezer Models 2134 mm PRO 48 S I D E - B Y- S I D E 606 mm Model ICB648PRO Built-In or Free-Standing Model ICB648PROG with Glass Door Built-In or Free-Standing 1219 mm 657 mm 1219 mm 766 mm Model ICB648PRO Model ICB648PROG with Glass Door Width 1219 mm Width 1219 mm Height 2134 mm Height 2134 mm Depth 606 mm* 657 mm** Depth 606 mm* 657 mm** *Depth from behind face frame to back of unit for standard installation.
ACCESSORIES Optional accessories are available through your Sub-Zero dealer. 18 ANTI-TIP BLOCKING KIT ADDING PANELS To prevent the unit from tipping forward and to provide a stable installation, the unit must be secured in place with an anti-tip blocking kit. If there is a solid soffit above the unit with clearance between the unit and the soffit of 25 mm or less, you won‘t need to block the unit.
OVERLAY DOOR PANELS If you and your client have ordered an overlay design model, you will be adding panels to give the unit the custom Sub-Zero look. The overlay panel design option is available on all Built-In units except Models ICB648PRO and ICB648PROG. For exact door panel dimensions for Built-In overlay models, refer to the Overlay Panel Specifications on pages 22–23.
OVERLAY DOOR PANELS I N S TA L L AT I O N To install overlay panels, see the detailed procedures outlined in the Sub-Zero Built-In Installation Guide. For glass door Models I601RG, I611G and I650G, the refrigerator door panel must include a cutout to accommodate the window. Refer to the Overlay Panel Specifications for Models I601RG, I611G and I650G on page 22. Illustration 8 shows how you can box out a landing space for the bezel using stiles and rails to create this space.
HANDLE HARDWARE SIDE PANELS Overlay models come without handle hardware. The beauty of this design is that you can match the surrounding cabinet hardware. You or the cabinet manufacturer must provide handle hardware to match the overall decorating scheme. Side panels can be used with the overlay and stainless steel design applications. When planning for side panels with the installation of a Built-In model, you need to be aware of space configuration to achieve a pleasing fit.
O V E R L AY D O O R PA N E L S P E C I F I C AT I O N S O V E R L AY D O O R PA N E L S P E C I F I C AT I O N S All Refrigerator | All Freezer Overlay (O) Models Over-and-Under Overlay (O) Models Model I601R W H Model I611 W H Refrigerator Overlay Panel 875 mm 1505 mm Refrigerator Overlay Panel 722 mm 1241 mm Refrigerator Spacer Panel 851 mm 1481 mm Refrigerator Spacer Panel 699 mm 1205 mm Refrigerator Backer Panel 867 mm 1497 mm Refrigerator Backer Panel 714 mm 1221 mm Freezer
O V E R L AY D O O R PA N E L S P E C I F I C AT I O N S OVERLAY GRILLE PANEL Side-by-Side Overlay (O) Models Overlay (O) Models Width Dimensions Model I661 W H Models I611 and I611G W Refrigerator Overlay Panel 494 mm 1727 mm Overlay Panel Width 722 mm Refrigerator Spacer Panel 470 mm 1703 mm Spacer Panel Width 699 mm Refrigerator Backer Panel 486 mm 1719 mm Backer Panel Width 714 mm Freezer Overlay Panel 379 mm 1727 mm Freezer Spacer Panel 356 mm 1703 mm Models I650, I650G, I
PANEL AND HANDLE PROFILE – OVERLAY AND STAINLESS STEEL APPLICATION STANDARD STAINLESS STEEL HANDLE 1" 51 mm 76 mm 32 mm PANEL 25 mm PANEL 19 mm PANEL 16 mm PANEL 13 mm PANEL 6 mm PANEL 6 mm APPROXIMATE THICKNESS OF WRAPPED STAINLESS STEEL DOOR DOOR NOTE: FOR OVERLAY APPLICATIONS, OPTIONAL STAINLESS STEEL HANDLE MUST BE MOUNTED ON PANEL MINIMUM 16 mm THICK.
PANEL AND HANDLE PROFILE – 130˚ DOOR OPENING The full-scale illustration shows the panel and handle profile for 130˚ door opening with a 51 mm filler strip. Interference of door panels with handles at maximum door swing may require the use of an optional 90˚ door stop available through your Sub-Zero dealer.
OVERLAY PANEL APPLICATION – 90˚ DOOR OPENING (TOP VIEW) The full-scale illustration shows what considerations you need to make for overlay panel applications and how they may interact with adjacent cabinets and countertops.
INTEGRATED REFRIGERATION A L L R E F R I G E R AT O R | A L L F R E E Z E R NEW For generations, the Sub-Zero name has been synonymous with built-in refrigeration. With the Integrated line, we‘ve taken the idea a step further—refrigerators and freezers you can hide anywhere in the house, inside the furniture or cabinetry of your choosing. Created to blend invisibly into your home‘s decor, the Integrated line lets you integrate refrigeration into the kitchen, master suite, media room or workout room.
MODEL I700TR MODEL I736TR A L L R E F R I G E R AT O R A L L R E F R I G E R AT O R S P E C I F I C AT I O N S NEW MODEL I700TFI ALL FREEZER S P E C I F I C AT I O N S S P E C I F I C AT I O N S Overall Width 686 mm Overall Width 914 mm Overall Width 686 mm Overall Height 2032 mm Overall Height 2032 mm Overall Height 2032 mm Overall Depth 610 mm Overall Depth 610 mm Overall Depth 610 mm Refrigerator Capacity 439 L Refrigerator Capacity 595 L Freezer Capacity 433 L Min Height
MODEL I700TCI MODEL I736TCI OVER-AND-UNDER OVER-AND-UNDER S P E C I F I C AT I O N S S P E C I F I C AT I O N S Overall Width 686 mm Overall Width 914 mm Overall Height 2032 mm Overall Height 2032 mm Overall Depth 610 mm Overall Depth 610 mm Refrigerator Capacity 289 L Refrigerator Capacity 383 L Freezer Capacity 144 L Freezer Capacity 195 L Min Height Required 2019 mm Min Height Required 2019 mm Door Swing Clearance 648 mm Door Swing Clearance 876 mm Specify Door Swing LH
MODEL I700BR MODEL I700BFI MODEL I700BCI R E F R I G E R AT O R D R A W E R S FREEZER DRAWERS R E F R I G E R AT O R | F R E E Z E R DRAWERS S P E C I F I C AT I O N S S P E C I F I C AT I O N S S P E C I F I C AT I O N S Overall Width 686 mm Overall Width 686 mm Overall Width 686 mm Overall Height 876 mm Overall Height 876 mm Overall Height 876 mm Overall Depth 610 mm Overall Depth 610 mm Overall Depth 610 mm Refrigerator Capacity 150 L Freezer Capacity 144 L Refrigerator Cap
INTEGRATED FEATURES All Integrated models accept wood or stainless steel panels. The optional stainless steel panels and handles are available in classic stainless steel at the 2032 mm and 2134 mm height. Stainless steel panels are ordered and shipped as sales accessories. Functional Design. These models can be placed anywhere in the home. Think about “point-ofuse refrigeration” when planning where to place your units. Integrated Design. All Sub-Zero models are 610 mm deep.
PLANNING INFORMATION Before moving the Integrated unit into place, be sure that the finished opening dimensions, electrical and plumbing locations and minimum door and drawer clearances are accurate. Refer to the Installation Specifications illustration for your model on the following pages. Be sure your installer has this information before finishing work is completed. I N S TA L L AT I O N Refer to the installation instructions shipped with each Sub-Zero product for detailed specifications.
OVERALL DIMENSIONS Models I700TR, I700TFI and I700TCI 686 mm 610 mm TOP OF ROUGH OPENING (UNIT DIMENSION) 356 mm (UNIT DIMENSION) A L L R E F R I G E R AT O R ALL FREEZER 21 mm 610 mm DOOR MOUNTING DETAIL DOOR/ DRAWER CLOSED Model I700TR All Refrigerator DOOR/ DRAWER CLOSED Model I700TFI All Freezer with Ice Maker 2032 mm* 90˚ 648 mm* 1995 mm* 10 mm 495 mm* 105˚ OVER-AND-UNDER Refrigerator | Freezer 657 mm 337 13 mm mm DRAWER MOUNTING DETAIL 117 mm* 90˚ DOOR OPENING Model I700TCI wit
OVERALL DIMENSIONS Models I736TR and I736TCI 914 mm 610 mm TOP OF ROUGH OPENING (UNIT DIMENSION) 356 mm (UNIT DIMENSION) A L L R E F R I G E R AT O R 33 mm Model I736TR All Refrigerator 610 mm DOOR MOUNTING DETAIL DOOR/DRAWER CLOSED DOOR/DRAWER CLOSED 2032 mm* OVER-AND-UNDER Refrigerator | Freezer 90˚ Model I736TCI with Ice Maker 1976 mm* 10 mm 495 876 mm* mm* 105˚ 886 mm 337 13 mm mm DRAWER MOUNTING DETAIL 90˚ DOOR OPENING 876 mm* 260 mm MAXIMUM DOOR OPENING TOP VIEW 178 mm* *DOO
OVERALL DIMENSIONS Models I700BR, I700BFI and I700BCI 10 mm 686 mm 610 mm (UNIT DIMENSION) (UNIT DIMENSION) DRAWERS 337 13 mm mm DRAWER MOUNTING DETAIL Model I700BR All Refrigerator 610 mm 876 mm* 260 mm 518 mm Model I700BFI All Freezer with Ice Maker DRAWER CLOSED Model I700BCI Refrigerator | Freezer with Ice Maker 248 mm 495 mm* 102 mm FRONT VIEW SIDE VIEW *13 mm +_ ADJUSTMENT IN LEVELING LEGS 657 mm TOP VIEW *DRAWER PANEL THICKNESS NOT INCLUDED TOP VIEW I N S TA L L AT I O N S P E C
PANEL REQUIREMENTS Door and drawer panels must be a minimum of 16 mm thick. The door panel cannot exceed 18 kg and each drawer panel must not exceed 5 kg for 686 mm wide units. For 914 mm wide units, the door panel weight limit is 24 kg and 7 kg for each drawer panel. CABINETRY APPLICATIONS FRAMED CABINETRY Integrated refrigeration is compatible with virtually any style and look of cabinetry. The models can be used with framed as well as frameless cabinets.
FRAMED CABINETRY – BEADED INSET APPLICATION The illustration below shows a 686 mm wide Integrated base or tall unit installed within a framed cabinetry, beaded inset application. Review, giving particular attention to the overall panel specifications. Also refer to the full-scale illustrations at the end of this section for specifics on door openings. 686 mm WIDE MODELS Installation of a 686 mm wide Integrated base or tall unit within framed cabinetry.
FRAMED CABINETRY – BEADED INSET APPLICATION The illustration below shows 914 mm wide Integrated tall unit installed within a framed cabinetry, beaded inset application. Review, giving particular attention to the overall panel specifications. Also refer to the full-scale illustrations at the end of this section for specifics on door openings. 914 mm WIDE MODELS Installation of a 914 mm wide Integrated tall unit within framed cabinetry. 610 mm CABINET DOOR DOOR PANEL *Dimensions may vary.
679 mm* FRAMELESS CABINETRY 610 mm PANEL WIDTH The illustrations show hypothetical installations of Integrated base or tall units within frameless cabinetry. Review, giving particular attention to the overall panel specifications. Also refer to the full-scale illustrations at the end of this section for specifics on door openings. A 1153 mm 2032 mm* 686 mm WIDE MODELS 2029 mm* Installation of a 686 mm wide Integrated base or tall unit within frameless cabinetry. A 345 mm A *Dimensions may vary.
PANEL CONSIDERATIONS The illustrations below provide panel width dimensions for installation of a single tall unit, 686 mm and 914 mm wide models. Illustrations on the following page provide panel width dimensions for installing two tall units side by side, 686 mm wide models and 914 mm wide models. IMPORTANT NOTE: The depth of each Integrated model is 610 mm from the front of the unit to its back.
As the reveal between cabinets and the Integrated unit decreases, the potential exists for severe finger pinching or crushing if a hand or fingers are placed in the opening when the door is closing. When 19 mm or thicker panels are used and a reveal less than 6 mm is maintained, the door panels may cause damage to the Sub-Zero unit when the door is open at the maximum 105˚ stop. You should use the built-in 90˚ stop to prevent damage.
INSTALLATION OPTIONS The illustrations show some typical installations and their dimension considerations. The depth dimension in the illustrations may vary depending on cabinet styles, treatment of countertops or other design options. ACCESSORIES Optional accessories are available through your Sub-Zero dealer. IMPORTANT NOTE: The depth of each Integrated model is 610 mm from the front of the unit to its back. Your design may necessitate moving the unit back or cabinets forward to achieve a flush fit.
DOOR PANEL HEIGHT TOE KICK CLEARANCE The height of the door panel can grow beyond 1153 mm and exceed the 2032 mm overall height, as long as you stay below the recommended door panel weight limit. The toe kick clearance can vary with the height of the lower drawer panel; the maximum panel height is 424 mm. The top illustration shows how the panel may grow and what you need to consider doing to finish the area in back of the door panel.
FRAMED CABINETRY IMPORTANT NOTE: The depth of each Integrated model is 610 mm from the front of the unit to its back. Your design may necessitate moving the unit back or cabinets forward to achieve a flush fit. DOOR CLOSED SUB-ZERO DOOR 105˚ MAXIMUM DOOR OPENING Full-scale (top view) 1/4 scale (top view) 610 mm TO BACK OF UNIT LINE OF INTERFERENCE* LINE OF INTERFERENCE* AT MAXIMUM DOOR OPENING MOUNTING BRACKET SCREW 3 mm min.
FRAMELESS CABINETRY IMPORTANT NOTE: The depth of each Integrated model is 610 mm from the front of the unit to its back. Your design may necessitate moving the unit back or cabinets forward to achieve a flush fit. SUB-ZERO DOOR 19 mm DOOR PANEL COUNTERTOP SIDE PANEL 105˚ MAXIMUM DOOR OPENING DOOR CLOSED 1/4 scale (top view) Full-scale (top view) Adjacent side panel and countertop application. 610 mm TO WALL LINE OF INTERFERENCE* LINE OF INTERFERENCE* AT MAXIMUM DOOR OPENING 3 mm min.
WINE STORAGE UNDERCOUNTER 606 mm 864 mm 616 mm 868 mm MODEL I424 MODEL I424FS Built-In Free-Standing ALL WINE STORAGE Sub-Zero‘s innovative addition to its complete line of residential refrigeration is wine storage equipment—the ultimate in beauty, engineering, and attention to detail. From the exterior and the smooth lines of the free-standing Model I424FS classic stainless steel to the ability to use wood on the Built-In and Integrated models, each unit is beautiful.
FEATURES AND OPTIONS When looking for wine storage, you no longer have to think only about an undercounter application. Sub-Zero offers you complete flexibility from the perspective of design applications and storage capabilities. Model I424 comes in the overlay and stainless steel door panel configurations. Model I424FS (free-standing) is identical to the Model I424 but with classic stainless steel exterior and is designed to be attractive in a stand-alone setting.
MODEL I424 MODEL I424FS MODEL I427 UNDERCOUNTER B U I LT- I N UNDERCOUNTER FREE-STANDING ALL WINE STORAGE MODEL OPTIONS S P E C I F I C AT I O N S S P E C I F I C AT I O N S Overlay Design I424/O Overall Width 616 mm Overall Width 686 mm Classic Stainless Steel I424/S Overall Height 868 mm Overall Height 2032 mm Overall Depth 625 mm Overall Depth 610 mm S P E C I F I C AT I O N S Wine Storage Capacity 46 bottles* Wine Storage Capacity 132 bottles* Overall Width 606 mm Door Sw
MODEL I430 MODEL I427R ALL WINE STORAGE W I N E S T O R A G E | R E F R I G E R AT O R MODEL OPTIONS *750 ml bottles.
ACCESSORIES Optional accessories are available through your Sub-Zero dealer. I N S TA L L AT I O N Refer to the installation instructions shipped with each Sub-Zero product for detailed specifications. PLANNING INFORMATION ELECTRICAL REQUIREMENTS Review the Overall Dimensions and Installation Specifications illustrations for your Wine Storage model on the following pages.
OVERALL DIMENSIONS Undercounter Wine Storage 606 mm 587 mm 625 mm 616 mm (CABINET DIMENSION) 597 mm DOOR FRAME (CABINET DIMENSION) UNDERCOUNTER 273 mm 864 mm* CENTERED VERTICALLY Model I424 Built-In 868 mm* 767 mm Model I424FS Free-Standing DOOR FRAME 102 mm 102 mm FRONT VIEW TOE KICK SIDE VIEW FRONT VIEW *13 mm +_ ADJUSTMENT IN LEVELING LEGS SIDE VIEW *13 mm +_ ADJUSTMENT IN LEVELING LEGS MODEL I424 MODEL I424FS Built-In Free-Standing Width 606 mm Width 616 mm Height 864 mm
OVERALL DIMENSIONS All Wine Storage – Model I427 Wine Storage | Refrigerator – Model I427R 686 mm 664 mm DOOR FRAME 356 mm 686 mm 664 mm DOOR FRAME 356 mm 610 mm (UNIT DIMENSION) 610 mm (UNIT DIMENSION) I N T E G R AT E D 20 mm 20 mm Model I427 All Wine Storage 1139 mm Model I427R Wine Storage | Refrigerator 273 mm OVERALL DIMENSIONS 1997 mm* CENTERED VERTICALLY DOOR FRAME WITH HINGES 273 mm 2032 mm CENTERED VERTICALLY 2032 mm 1789 mm DOOR FRAME WITH HINGES 1997 mm* 9 mm Model I427 | I
OVERALL DIMENSIONS All Wine Storage – Model I430 762 mm 606 mm 719 mm DOOR FRAME ALL WINE STORAGE Model I430 Built-In CENTERED VERTICALLY 2134 mm OVERALL DIMENSIONS Model I430 273 mm 1724 mm DOOR FRAME Width 762 mm Height 2134 mm Depth 610 mm Note the location of pre-drilled holes for optional handle hardware.
ACCESSORIES Optional accessories are available through your Sub-Zero dealer. 54 DOOR PANELS MODEL I424FS – FREE-STANDING Unless you are installing a stainless steel model, you will need to provide a frame for the glass door. If you order a stainless steel unit, Models I424, I424FS and I430 will be shipped with their panels and hardware installed and you will merely install the Sub-Zero. However, for Models I427 and I427R, you will have to have the stainless steel panels and handles installed.
OVERLAY PANELS – MODEL I424 The overlay panel applied to Model I424 should not be confused with the Built-In overlay panel application. The overlay panel will consist of only a frame and would be either the 16 mm or 19 mm thick panel you may be using. It is affixed directly to the door itself with screws through a series of pre-drilled holes in the perimeter of the door itself. You do not need any backer or spacer panel.
INTEGRATED PANELS – MODELS I427 | I427R ACCESSORIES Optional accessories are available through your Sub-Zero dealer. The integrated frame panels for glass doors for these models will follow some of the identical planning processes used with the Integrated line. The installation of the door panels is completely different, however. Rather than using the mounting hardware we used with the Integrated line, door panels for both Models I427 and I427R will be applied with screws applied through our door.
IMPORTANT NOTE: The dimensions of these panels and stiles are assuming the models finish off at 2032 mm in height overall and have a 102 mm toe kick for the Model I427. If you finish off at 2134 mm, for instance, you must add 102 mm additional to the overall height of the panel and remember to add 102 mm to the top rail. Likewise, if you allow for a 152 mm toe kick for the Model I427, you must subtract 51 mm from the bottom rail.
OVERLAY PANELS – MODEL I430 Your overlay model will be shipped without handle hardware and with an 279 mm overlay panel grille as standard equipment. You will need to order a panel for the grille and hardware to complement your surrounding cabinetry. While the overlay panel design offers you a more seamless appearance, you need to be aware of adjacent cabinets and/or countertops when the door is opened. Refer to the full-scale illustrations at the end of the Built-In section.
The back sides of rails and stiles that will be visible through the glass door will need to be finished. Also, the inside edges of the frames must be finished to match the front surface. In addition, side panel information for a Model I430 is available on page 21 of the Built-In section. Refer to illustration 11 on page 21 for placement of toe kick and grille area cut-outs.
ACCESSORIES Optional accessories are available through your Sub-Zero dealer. HARDWARE CONSIDERATIONS WINE SHELF WOOD FACING With Model I424 (overlay), Models I427 and I427R (integrated) and Model I430 (overlay), you must supply your own handle hardware. It is recommended you use our optional handles and use the pre-drilled holes supplied to locate the handles within the frame of our unit. The metal frame on the door has numerous mounting holes on each side to accommodate Sub-Zero accessory handles.
DOOR FRAME PROFILE DOOR FRAME HANDLE OFFSET Wine Storage Models Glass Cabinet Door Profile CL A Dimension A Model I424 25 mm Model I427 22 mm Model I427R 22 mm Model I430 24 mm IMPORTANT NOTE: Rails and stiles must be a minimum of 57 mm wide (except for the rails of Models I427 and I427R, which must be wide enough to cover the door hinges). The back sides of rails and stiles that will be visible through the glass door will need to be finished.
MODEL I424 – DOOR CLOSED AND 145˚ MAX OPENING 610 mm CABINETRY OPENING 587 mm TO BACK OF APPLIANCE *MODEL I424 MUST EXTEND A MINIMUM 6 mm BEYOND THE FRONT SURFACE OF ADJOINING CABINETRY TO ALLOW THE MAXIMUM DOOR SWING SUB-ZERO DOOR 19 mm 13 mm DOOR PANEL 6 mm* 3 mm 600 mm DOOR PANEL WIDTH DOOR PANEL 145˚* The full-scale illustration shows what considerations you need to make for the installation of Model I424 and how the maximum door opening may interact with adjacent cabinets and countertops.
NEW UNDERCOUNTER REFRIGERATION Available in 2007 NEW A L L R E F R I G E R AT O R 606 mm Aside from the full-size models that Sub-Zero offers in its Built-In and Integrated lines of refrigeration and its Wine Storage equipment, we round out our product line-up with a new line of Undercounter refrigeration available in 2007.
MODEL UC-24R NEW A L L R E F R I G E R AT O R MODEL UC-24B NEW BEVERAGE CENTER MODEL UC-24C NEW C O M B I N AT I O N R E F R I G E R AT O R | F R E E Z E R MODEL OPTIONS S P E C I F I C AT I O N S Overlay Design UC-24B/O Classic Stainless Steel UC-24B/S S P E C I F I C AT I O N S S P E C I F I C AT I O N S Overall Width 606 mm Overall Width 606 mm Overall Width 606 mm Overall Height 864 mm Overall Height 864 mm Overall Height 864 mm Overall Depth 610 mm Overall Depth 610 mm O
MODEL UC-24RO NEW MODEL 315IP A L L R E F R I G E R AT O R OUTDOOR MODEL ICE MAKER S P E C I F I C AT I O N S S P E C I F I C AT I O N S ACCESSORIES 606 mm Overall Width 386 mm Overall Height 864 mm Overall Height 854 mm Overall Depth 610 mm Overall Depth 610 mm 161 L Ice Storage Capacity 12 kg 870 mm Min Height Required 857 mm 645 mm Door Swing Clearance 387 mm Specify Door Swing LH or RH Shipping Weight 45 kg Shipping Weight 59 kg Overall Width Refrigerator Capacity Min H
UNDERCOUNTER FEATURES UNDERCOUNTER MODEL FEATURES Overlay Application. The overlay application blends seamlessly into your overall room design and complements surrounding cabinetry. You add the decorative door front panel and hardware. Sub-Zero accessories handles are available. The overlay application is available for all Undercounter models except Model UC-24RO. Model UC-24B must be ordered specifically as overlay (UC24-B/O). Electronic Controls.
PLANNING INFORMATION ELECTRICAL REQUIREMENTS Refer to the Installation Specifications for information regarding area requirements, minimum door clearance, placement of electrical and plumbing (Models UC-24C and 315IP). A 115 V AC, 60 Hz, 15 amp circuit breaker and electrical supply are required. A separate circuit, servicing only this appliance is required. PLUMBING REQUIREMENTS For Models UC-24C and 315IP, rough in the water supply line. Connect a 6.
I N S TA L L AT I O N DRAIN PUMP – MODEL 315IP DOOR PANEL – MODEL 315IP This ice maker comes with a built-in drain pump. The drain and inlet water tubes must be plumbed before connecting to the ice maker. An air gap will likely be required between the ice maker drain tube and the drain/waste receptacle. A stand pipe with a trap below it would be acceptable for the drain/waste receptacle. Refer to the illustrations below.
OVERLAY DOOR PANEL – MODELS UC-24R AND UC-24C OVERLAY DOOR PANEL – MODEL UC-24B The overlay door panel design allows for a decorative panel to cover the door trim for a seamless appearance that will compliment surrounding cabinetry. You may also choose to match the handle hardware of surrounding cabinetry. The overlay door panel applied to the Model UC-24B will consist of only a frame and will affix directly to the door with screws through a series of predrilled holes in the perimeter of the door.
DOOR FRAME PROFILE – MODEL UC-24B Glass FULL-SCALE T E M P L AT E S The full-scale illustrations on the following pages enable you to understand some of the unique situations you may face as you plan for the installation of the Undercounter units. Use these illustrations as templates. Door Panel Profile CL 25 mm The full-scale illustration shows the door frame profile for Model UC-24B. 25 mm IMPORTANT NOTE: Rails and stiles must be a minimum of 57 mm wide.
UNDERCOUNTER DOOR CLOSED AND 145˚ MAX OPENING 610 mm CABINETRY OPENING 587 mm TO BACK OF APPLIANCE SUB-ZERO DOOR 19 mm 13 mm *UNDERCOUNTER UNIT MUST EXTEND A MINIMUM 6 mm BEYOND THE FRONT SURFACE OF ADJOINING CABINETRY TO ALLOW THE MAXIMUM DOOR SWING DOOR PANEL 6 mm* 3 mm 600 mm DOOR PANEL WIDTH DOOR PANEL 145˚* The full-scale illustration shows what considerations you need to make for the installation of the Undercounter unit and how the maximum door opening may interact with adjacent cabinets an
SUB-ZERO, INC. P O BOX 44130 MADISON, WI 53744 USA SUBZERO.
