200 IG 3758400 1-04.
00 IG 3758400 1-04.
200 IG 3758400 1-04.qxd 1/2/2004 7:55 AM Page 3 200 SERIES I N S T A L L A T I O N Before you begin your installation of a Sub-Zero 200 Series unit, there are a few things you should take special care to observe. By reading these introductory instructions carefully, you will make the installation procedure easier, problemfree and, most important, safe. G U I D E Second, make sure that the actual equipment that was shipped to you matches the design you are expecting to install.
200 IG 3758400 1-04.qxd 1/2/2004 7:55 AM Page 4 200 SERIES P R E - I N S T A L L A T I O N S P E C I F I C A T I O N S MODELS 249R, 249R, 249FF AND 245 P R E PA R I N G T H E S PA C E ROUGH-IN REQUIREMENTS Step 1: First, make sure that the opening where the Sub-Zero is to be installed is properly prepared. Refer to the Pre-Installation Specifications illustrations and chart to be sure the space dimensions, electrical service and plumbing are correct for the model you are about to install.
200 IG 3758400 1-04.qxd 1/2/2004 7:55 AM Page 5 200 SERIES P R E - I N S T A L L A T I O N S P E C I F I C A T I O N S Finished Rough Opening Width (A) Finished Rough Opening Height (B) Model 249R 24"(610) 34 1/2"(876) Model 249RP 24"(610) 34 1/2"(876) Model 249FF 24"(610) 34 1/2"(876) Model 245 24"(610) 34 1/2"(876) NOTE: Dimensions in parentheses are in millimeters. Refer to illustration on page 4.
200 IG 3758400 1-04.qxd 1/2/2004 7:55 AM Page 6 200 SERIES I N S T A L L A T I O N P R E PA R I N G E L E C T R I C A L CONNECTIONS Step 3: To prepare the electrical system, rough in the electrical outlet following the Pre-Installation Specifications. You will need a 115 volt, 60 Hertz electrical supply. Dedicate a separate 15 amp fuse or circuit breaker to the Sub-Zero unit, and follow any local codes that apply.
200 IG 3758400 1-04.qxd 1/2/2004 7:55 AM Page 7 200 SERIES I C E M A K E R O P E R AT I O N : U N PA C K I N G T H E S U B - Z E R O After the water has been hooked up to the icemaker, lower stop arm of icemaker. Step 5: Unpack the unit, remove the unit shipping carton. Remove the wood base by extracting all 4 levelers and then discard the wood base. Reinstall all 4 levelers back into the unit base assembly. Remove all packing materials and tape as well. Do not discard the kickplate.
200 IG 3758400 1-04.qxd 1/2/2004 7:55 AM Page 8 200 SERIES C O M P L E T I N G T H E I N S TA L L AT I O N CAUTION Step 9: Now, level the unit. Adjust both the front and rear levelers by turning the levelers clockwise - to raise the unit, counterclockwise - to lower the unit. When the unit is leveled properly, or squared off, door adjustments are less likely to be necessary. (See Figure 3.) Protect any finished flooring before moving the unit in place.
200 IG 3758400 1-04.qxd 1/2/2004 7:55 AM Page 9 200 SERIES I N S TA L L I N G PA N E L S Before you begin installing panels, refer to the Panel Specifications Dimensions on page 5, and be sure you are working with the Sub-Zero panel design called for in your installation plans. No panels or handle hardware are necessary to install. All Sub-Zero undercounter units are manufactured in a manner to achieve a total built-in appearance.
200 IG 3758400 1-04.qxd 1/2/2004 7:55 AM Page 10 200 SERIES ADJUSTING THE HINGES DOOR SWING CHANGE It is possible that doors may come out of adjustment If doors need adjustment, please refer to the follwoing door adjustment directions. Model 245: Upper; interchange hinge, screws and corner cap with hole plugs and corner cap on opposite side of cabinet and door. Lower; interchange hinge and screws with hole plugs on opposite side of cabinet.
200 IG 3758400 1-04.qxd 1/2/2004 7:55 AM Page 11 200 SERIES C H E C K I N G T H E R E S U LT S SERVICE FOR YOUR SUB-ZERO R E F R I G E R AT I O N S Y S T E M That's it. You've completed the installation of a Sub-Zero 200 Series refrigerator / freezer. But you're not finished yet. Go over our checklist of installation steps. If you need service, check the model and serial number on the plate at the top frame of the unit inside the door.
200 IG 3758400 1-04.qxd 1/2/2004 7:55 AM Page 12 200 200 SERIES S U B - Z E R O F R E E Z E R C O M P A N Y, I N C . 4717 Hammersley Road • Madison, Wisconsin 53711 (800) 222-7820 • (608) 271-2233 • E-mail: customerservice@subzero.
