ITEM #0355455 #0355452 #0354705 Portfolio® is a registered trademark of LF, LLC. All Rights Reserved. 3-LIGHT VANITY BAR MODEL #VB256-3BNK #VB256-3CH #VB256-3WDBZ Français p. 10 Español p. 19 ATTACH YOUR RECEIPT HERE Serial Number Purchase Date Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-800-643-0067, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. 5 p.m., EST, Friday. EB15165 Lowes.
PACKAGE CONTENTS PART A B C D DESCRIPTION Fixture Mounting Plate (preassembled to fixture (A)) Socket Ring (preassembled to fixture (A)) Mounting Plate Screw (preassembled to fixture (A)) QUANTITY 1 1 A 3 4 B C D HARDWARE CONTENTS (shown actual size) AA E3 Wire Connector BB Machine Screw Qty. 3 CC DD Wall Anchor Screw Wall Anchor Qty. 2 Qty. 2 Qty. 2 SAFETY INFORMATION READ AND SAVE THESE INSTRUCTIONS.
SAFETY INFORMATION DANGER • DO NOT connect the bare or green insulation fixture ground wire to the black (HOT) current-carrying wire or the white neutral house wire. Connection of the bare or green fixture ground wire to the black or white house wires may cause metal parts of the fixture to carry electrical currents. Under this condition, anyone coming in contact with the fixture will receive electrical shock, which could cause serious injury or death.
PREPARATION Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product. Estimated Assembly Time: 45 - 60 minutes Tools Required for Assembly (not included): Flathead Screwdriver, Phillips Screwdriver, Wire Strippers, Pliers, Wire Cutters, Safety Glasses, Stepladder, Drill, 1/8 in.
ASSEMBLY INSTRUCTIONS 3. Remove mounting plate (B) from fixture (A) by removing mounting plate screws (D) from the edges of the fixture (A). Save mounting plate screws (D) for later use. 3 D B E A D 4a. To mount the item directly to an outlet box (not included), first attach mounting plate (B) to outlet box using the existing washers and outlet box screws or the machine screws (BB).
ASSEMBLY INSTRUCTIONS 4b. To mount the item directly to wall, determine the approximate location for the fixture (A). Place the mounting plate (B) against the wall and mark the location of the slots on the mounting plate (B) using a pencil or a marker (not included). Set mounting plate (B) aside. 4b Pre-drilled holes B DD CC Then, using a 1/8 in. drill bit (not included), drill two pilot holes at the marked locations.
ASSEMBLY INSTRUCTIONS NOTE: The drawings in Figs. 5 - 7 are applicable for mounting options 4a and 4b. 5. Unwrap BARE wire from BLACK and WHITE wires on fixture (A). Prepare wires by stripping 3/4 in. of insulation from wire ends using wire strippers (not included). Connect WHITE wire from fixture (A) to WHITE wire from outlet box/wall using existing wire connector or wire connector (AA).
ASSEMBLY INSTRUCTIONS 7. Align holes in fixture (A) with screw holes in mounting plate (B) and push fixture (A) toward wall. Attach fixture (A) to mounting plate (B) using the mounting plate screws (D) previously removed (Step 3, page 5). Note: Fixture (A) can be installed with the sockets facing either up or down. 7 D B A D 8. Remove socket rings (C) from sockets of fixture (A). Attach glass shades (sold separately) to sockets, securing with socket rings (C).
CARE AND MAINTENANCE • Shut off main power supply. Wipe fixture with soft, damp cloth. Use window cleaner to clean glass. Do not use an abrasive cleaner on glass or fixture. TROUBLESHOOTING WARNING: Before beginning work, shut off the power supply to avoid electrical shock. PROBLEM Bulb(s) will not light. POSSIBLE CAUSE 1. Bulb(s) is/are burned out. 2. Power is OFF. 3. Faulty connection. CORRECTIVE ACTION 1. Replace light bulb(s). 2. Make sure power supply is ON. 3. Check wiring and all connections.