Installation Guide

ManualsBrandsStyle Selections ManualsFreestanding Shelving Units143654W-DS

ITEM #0190443,0062870,0064014

4-TIER SHELF RACK

MODEL #143654W-DS,143654B-DS,143654C-DS

ATTACH YOUR RECEIPT HERE

Serial Number _______________________ Purchase Date _______________________

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 1-877-888-8225, 8 a.m. - 8 p.m., EST, Monday - Friday.

Français

p.9

Español p.17

Summary of content (8 pages)

PAGE 1
ITEM #0190443,0062870,0064014 TM 4-TIER SHELF RACK MODEL #143654W-DS,143654B-DS,143654C-DS Français p.9 Español p.17 ATTACH YOUR RECEIPT HERE Serial Number _______________________ Purchase Date _______________________ Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-877-888-8225, 8 a.m. - 8 p.m., EST, Monday - Friday.
PAGE 2
PACKAGE CONTENTS D B C A PART DESCRIPTION QUANTITY A Shelves 4 B Top Rods (post joiners pre-installed in rods) 4 C Bottom Rods (foot levelers pre-installed in bottom of rods) 4 D Spacers 32 2
PAGE 3
HARDWARE CONTENTS AA Washer Qty. 2 BB CC Plastic Anchor Qty. 2 Screw Qty. 2 SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product. • • • • Two adults required for a safe assembly. Use care when handling. Do not allow children to climb or play in or around the shelves. Each shelf holds up to 350 lbs., evenly distributed. Assemble on a soft surface, such as carpeting, to avoid scratching the finish.
PAGE 4
ASSEMBLY INSTRUCTIONS 1. Screw the top rods (B) onto the threaded ends of the bottom rods (C). Be sure the connection is secure. 1 B C 2. Attach two spacers (D) at about the third groove (from the foot levelers) on each bottom rod (C) assembly. Note: Be sure the arrows on the spacers point upward. 2 D C 3. Place the bottom rods (C) through the corner holes of one shelf (A). Push the shelf (A) down until the corners fit securely over each spacer (D).
PAGE 5
4. Stand the assembly upright. 4 A C 5. Attach two spacers (D) at about the fifteenth groove (from the bottom shelf (A)) on each bottom rod (C) assembly. 5 D C 6. Place a second shelf (A) over the rods. Push down until the corners fit securely over each spacer (D).
PAGE 6
7. Attach two spacers (D) at about the fifteenth groove (from the second shelf (A)) on each bottom rod (C) assembly. 7 D C 8. Place a third shelf (A) over the top rods (B). Push down until the corners fit securely over each spacer (D). 8 B A C 9. Attach two spacers (D) at about the fifteenth groove (from the third shelf (A)) on each top rod (B) assembly.
PAGE 7
10. Slace the remaining shelf (A) over the top rods (B). Push down until the corners fit securely over each spacer (D). 10 A B C 11. To prevent the unit from tipping over, secure it to a wall in the following manner: Drill a hole in the wall using a 1/4 in. drill bit (not included). Insert the plastic anchor (BB) into the hole. Insert the screw (CC) through the washer (AA) then through the back of the top shelf wire and into the plastic anchor (BB) as shown.
PAGE 8
REPLACEMENT PART LIST For replacement parts, call our customer service department at 1-877-888-8225, 8 a.m. - 8 p.m., EST, Monday - Friday.