Manual

Issue 1, July 2018 Model 5330 User Guide
Page 22 Studio Technologies, Inc.
Specifications
Network Audio Technology:
Type: Dante audio-over-Ethernet
AES67-2013 Support: yes (for serial numbers
M5330-02001-later)
Dante Domain Manager (DDM) Support: yes
Bit Depth: up to 24
Sample Rates: 44.1 and 48 kHz
Number of Transmitter (Output) Channels: 4
Number of Receiver (Input) Channels: 4
Dante Audio Flows: 4; 2 transmitter, 2 receiver
Network Interface:
Type: twisted-pair Ethernet
Data Rate: 100 Mb/s (10 Mb/s not supported;
1000 Mb/s “GigE” Ethernet not supported unless
falls back to 100 Mb/s)
Inputs 1 and 2:
Compatibility: unbalanced line-level sources
Type: analog, unbalanced, capacitor coupled
Impedance: 10 k ohms, nominal
Nominal Level: –10 dBu, adjustable with input level
control
Maximum Level: depends on setting of the input
level control
Dynamic Range: >116 dB, 0 dB gain, A-weighted
Distortion (THD+N): <0.001% (–101 dB) at
–1 dBFS, 40 dB gain, 22 kHz bandwidth
Frequency Response: +0.0/–0.5 dB, 22 Hz to
22 kHz
Status LEDs: 2, displays signal present/peak
Inputs 3 and 4:
Compatibility: balanced or unbalanced line-level
sources
Type:
analog, electronically balanced, capacitor
coupled
Impedance: 20 k ohms, nominal
Nominal Level: +4 dBu (results in Dante output
level of –20 dBFS)
Maximum Level: +24 dBu (results in Dante output
level of 0 dBFS)
Dynamic Range: >116 dB, 0 dB gain, A-weighted
Distortion (THD+N): <0.001% (–101 dB) at
–1 dBFS, 40 dB gain, 22 kHz bandwidth
Frequency Response: +0.0/–0.5 dB, 22 Hz to
22 kHz
Status LEDs: 2, displays signal present/peak
IMain, Auxiliary, and Monitor Outputs:
Type: analog, electronically balanced, capacitor
coupled, intended to drive balanced or unbalanced
loads of 2 k ohms or greater
Source Impedance: 200 ohms
Nominal Level – Main and Auxiliary:
+4 dBu,
reference –20 dBFS on Dante input
Nominal Level – Monitor: 0 dBu, reference
–20 dBFS on Dante input
Maximum Level: +24 dBu with 0 dBFS on Dante
input
Dynamic Range: >119 dB, A-weighted
Distortion (THD+N): 0.0012% (–99 dB), measured
at –1 dBFS, 22 kHz bandwidth
Frequency Response: ±0.1 dB, 20 Hz to 20 kHz
Status LEDs: 4, displays signal present/peak
Audio Monitor:
Source: inputs 1-4 or main outputs 1-4, selectable
as monaural or stereo
Level Meters: 2, 8-segment LED
Headphone Output:
Type: stereo (dual-channel)
Compatibility: intended for connection to stereo
headphones with nominal impedance of 100 ohms
or greater
Maximum Output Voltage:
4.9 volts RMS, 1 kHz,
150 ohm load
Frequency Response: +0/–1.4 dB, 20 Hz to
20 kHz
Distortion (THD+N): 0.005%
Dynamic Range: >100 dB