Datasheet

Studio Technologies, Inc. Model 5330 Interface, Issue 1, Page 4
Simple Installation
The Model 5330 is housed in a lightweight aluminum
enclosure and mounts in one space (1U) of a standard
19-inch rack enclosure. The unit uses standard connec
-
tors to allow fast and convenient interconnections. This
includes 3-conductor male and female XLR connectors,
3.5 mm and ¼-inch jacks, and an IEC C14 receptacle for
mains power. The unit connects to a local area network
(LAN) using a standard RJ45 receptacle and supports
100 Mb/s twisted-pair Ethernet. Four LEDs on the back
panel display the status of the Ethernet connection and
Dante interface. The Model 5330 requires 100-240
volts, 50/60 Hz mains power for operation.
Future Capabilities and Firmware
Updating
The Model 5330 was designed so that its performance
and capabilities can be enhanced in the future. A USB
receptacle, accessible on the unit’s back panel, allows
the application firmware (embedded software) to be
updated using a USB flash drive. To implement its
Dante interface the Model 5330 uses one of Audinate’s
4-in/4-out Ultimo™ integrated circuit. The firmware
in this integrated circuit can be updated via the unit’s
Ethernet connection, helping to ensure that its Dante
capabilities remain up to date.
Studio Technologies, Inc.
Skokie, Illinois USA
© by Studio Technolog
ies, Inc., July 2018
studio-tech.com
Specifications
Network Audio Technology:
Type: Dante audio-over-Ethernet
AES67-2013 Support: yes
Dante Domain Manager (DDM) Support: yes
Bit Depth: up to 24
Sample Rates: 44.1 and 48 kHz
Number of Transmitter (Output) Channels: 4
Number of Receiver (Input) Channels: 4
Dante Audio Flows: 4; 2 transmitter, 2 receiver
Network Interface:
Type: twisted-pair Ethernet
Data Rate: 100 Mb/s (10 Mb/s not supported; 1000 Mb/s “GigE”
Ethernet not supported unless falls back to 100 Mb/s)
Inputs 1 and 2:
Compatibility: unbalanced line-level sources
Type: analog, unbalanced, capacitor coupled
Impedance: 10 k ohms, nominal
Nominal Level: –10 dBu, adjustable with input level control
Maximum Level: depends on setting of the input level control
Dynamic Range: >116 dB, 0 dB gain, A-weighted
Distortion (THD+N): <0.001% (–101 dB) at –1 dBFS, 40 dB gain,
22 kHz bandwidth
Frequency Response: +0.0/–0.5 dB, 22 Hz to 22 kHz
Status LEDs: 2, displays signal present/peak
Inputs 3 and 4:
Compatibility: balanced or unbalanced line-level sources
Type: analog, electronically balanced, capacitor coupled
Impedance: 20 k ohms, nominal
Nominal Level: +4 dBu (results in Dante output level of –20 dBFS)
Maximum Level: +24 dBu (results in Dante output level of 0 dBFS)
Dynamic Range: >116 dB, 0 dB gain, A-weighted
Distortion (THD+N): <0.001% (–101 dB) at –1 dBFS, 40 dB gain,
22 kHz bandwidth
Frequency Response: +0.0/–0.5 dB, 22 Hz to 22 kHz
Status LEDs: 2, displays signal present/peak
Main, Auxiliary, and Monitor Outputs:
Type: analog, electronically balanced, capacitor coupled, intended
to drive balanced or unbalanced loads of 2 k ohms or greater
Source Impedance: 200 ohms
Nominal Level – Main and Auxiliary: +4 dBu, reference –20 dBFS
on Dante input
Nominal Level – Monitor: 0 dBu, reference –20 dBFS on Dante input
Maximum Level: +24 dBu with 0 dBFS on Dante input
Dynamic Range: >119 dB, A-weighted
Distortion (THD+N): 0.0012% (–99 dB), measured at –1 dBFS,
22 kHz bandwidth
Frequency Response: ±0.1 dB, 20 Hz to 20 kHz
Status LEDs: 4, displays signal present/peak
Audio Monitor:
Source: inputs 1-4 or main outputs 1-4, selectable as monaural
or stereo
Level Meters: 2, 8-segment LED
Headphone Output:
Type: stereo (dual-channel)
Compatibility: intended for connection to stereo headphones with
nominal impedance of 100 ohms or greater
Maximum Output Voltage: 4.9 volts RMS, 1 kHz, 150 ohm load
Frequency Response: +0/–1.4 dB, 20 Hz to 20 kHz
Distortion (THD+N): 0.005%
Dynamic Range: >100 dB
Connectors:
Inputs 1 and 2: 3-conductor 3.5 mm jack
Inputs 3 and 4: 3-pin female XLR
Main, Auxiliary, and Monitor Outputs: 3-pin male XLR
Headphone Output: 3-conductor 3.5 mm jack and 3-conductor ¼-inch
jack
Ethernet: RJ45 receptacle
USB: type A receptacle (used only for application firmware updates)
AC Mains: 3-blade, IEC 320 C14-compatible (mates with IEC 320 C13)
Power Source:
AC Mains: 100 to 240 volts, +10/–15%, 50/60 Hz, 15 watt maximum
Dimensions – Overall:
19.0 inches wide (48.3 cm)
1.72 inches high (4.4 cm)
7.8 inches deep (19.8 cm); 8.2 inches (20.8 cm) overall
Mounting: one space (1U) in a standard 19-inch rack
Weight:
3.3 pounds (1.5kg)
Specifications subject to change without notice.