Datasheet

Studio Technologies, Inc. Model 410 SDI-Over-Fiber Transport System, Issue 2, Page 2
Model 410 Specifications
Ethernet Interface:
Type: 10/100, auto MDI/MDI-X
Connector: RJ45 (8-pin modular)
Status LEDs: 2, link and activity
Supported Protocols: HTTP, SNMP, DHCP, DNS
Display: vacuum fluorescent (emissive) with color
LED backlighting
Power Requirement:
10 to 18 volts DC, universal mains input/12 volt DC
output power supply shipped with each unit.
Model 410-3T: 0.7 A maximum @ 10 volts
Model 410-3R: 0.6 A maximum @ 10 volts
Model 410-3T/3R: 0.9 A maximum @ 10 volts
Connector: 4-pin male XLR-type
Battery Operation: optional cover with Anton-
Bauer® QR-Gold mount available (M410BMA-1)
Dimensions – Standard Portable
“Throw-Down” Version (Overall):
8.7 inches wide (22.1 cm)
1.72 inches high (4.4 cm)
8.00 inches deep (20.3 cm)
Mounting Options: single-unit (M410RM-1) or
dual-unit (M410RM-2) rack-mount front panels;
each uses one space (1U) in a standard 19-inch
rack
Weight: 1.8 pounds (0.82 kg)
SDI Inputs:
Quantity: 3, Model 410-3T and Model 410-3T/3R
Data Rate: 270 Mb/s to 2.97 Gb/s
Supported Standards: 3G-SDI (SMPTE 424M),
HD-SDI (SMPTE 292), SD-SDI (SMPTE 259M),
DVB-ASI (AES3 digital audio transport not
supported)
Connector: BNC, 3G-SDI optimized, gold plating
on center pin, per IEC 61169-8 Annex A
Type: unbalanced
Impedance: 75 ohms
SDI Loop-through Outputs:
Quantity: 3, Model 410-3T only
Source: re-clocked copy of input
Data Rate: 270 Mb/s to 2.97 Gb/s
Supported Standards: 3G-SDI, HD-SDI, SD-SDI,
DVB-ASI
Connector: BNC, 3G-SDI optimized, gold plating
on center pin, per IEC 61169-8 Annex A
Type: unbalanced
Impedance: 75 ohms
Level: 800 mV p-p, nominal
Optical Output:
Compliance: SMPTE 297 (as applicable)
Fiber Type: single-mode
Connector: ST PC (SC optional)
Multiplexed Wavelengths: 1310 nm (FP), 1490 nm
(DFB), 1550 nm (DFB)
Launch Power: –3 dBm nominal @ 1310 and
1550 nm; –1 dBm nominal @ 1490 nm
Typical Fiber Length: 10 km minimum
Studio Technologies, Inc.
Skokie, Illinois USA
[phone]
© by Studio Technolog
ies, Inc., November 2012
www.studio-tech.com
Optical Input:
Compliance: SMPTE 297 (as applicable)
Fiber Type: single-mode
Connector: ST PC (SC optional)
Wavelengths Supported: 1310 nm, 1490 nm, and
1550 nm
Receive Sensitivity: –17 dBm, nominal @ 2.97 Gb/s
Maximum Input Power: –3 dBm, nominal
Digital Video Outputs:
Quantity Model 410-3R: 6 (3 pair)
Quantity Model 410-3T/3R: 3
Data Rate: 270 Mb/s to 2.97 Gb/s
Supported Standards: 3G-SDI, HD-SDI, SD-SDI,
DVB-ASI
Connector: BNC, 3G-SDI optimized, gold plating
on center pin, per IEC 61169-8 Annex A
Type: unbalanced
Impedance: 75 ohms
Level: 800 mV p-p, nominal
Specifications subject to change without notice.
Model 410-3T Back Panel
connector. Included with each unit is a compact 100-240 volt
input/12 volt DC output power supply. An optional Model 410
cover assembly provides an Anton-Bauer QR-Gold mount,
allowing direct attachment of a broadcast-standard rechargeable
battery. With the Model 410’s modest energy requirement one
battery can support operation for many, many hours.
Remote Monitoring and Configuration
The Model 410 has an embedded web server that allows the user
to monitor system status through any web-enabled device such
as a personal computer or smartphone. System status can also
be communicated using SNMP, making it possible to integrate
the unit’s monitoring information into a networked alarm and
control software application.
The Model 410’s status screen lets a user or supervisor check
the status of SDI input and output channels, signal rate, and
whether the optical transmitters are enabled. The optical output
power of each electrical-to-optical (E2O) channel is reported
directly in dBm. The optical receive power (in dBm) of an optical-
to-electrical (O2E) channel is also displayed. This is a particularly
useful feature for remote system troubleshooting.
The embedded web server also provides a configuration menu,
allowing a variety of monitoring parameters to be set. These
include enabling alarms for loss of SDI inputs and outputs, low
optical transmit and receive levels, and excessive temperature.
Additional menu screens provide access to SNMP, network IP
address, and front-panel display configurations. Advanced
features include the ability to remotely update the Model 410’s
system firmware via the Ethernet connection.
Simple Installation
While the Ethernet-accessed monitoring and configuration func-
tions enhance the utility of the Model 410 they are not necessary
for basic SDI-over-fiber transport operation. Model 410 units
will deliver reliable, high-quality performance with no other
user actions outside of making SDI-over-coaxial cable, fiber,
and power connections. All back-panel connectors are clearly
labeled for simple, fast, and intuitive use. And the front-panel
display provides direct access to the unit’s most important status
information.
The Model 410 is housed in a small, rugged, and lightweight
aluminum enclosure that is designed to be “road tough.” It can
be used in this manner as a standalone portable unit for “throw-
down” applications. Two rack-mount options are also available
allowing one or two units to be mounted in one space (1U) of a
standard 19-inch rack enclosure.
Model 410-3R Back Panel
Model 410-3T/3R Back Panel