Manual

Model 209 User Guide Issue Preliminary 1, July 2021
Studio Technologies, Inc. Page 21
MODEL 209
TALENT CONSOLE
Specifications
Power Source:
Power-over-Ethernet (PoE): class 2 (low power,
≤6.49 watts) per IEEE® 802.3af
Network Audio Technology:
Type:
Dante audio-over-Ethernet
AES67-2018 Support: yes, selectable on/off
Dante Domain Manager (DDM) Support: yes
Bit Depth: up to 32
Encoding Choices: PCM 16, PCM 24, or PCM 32
Sample Rate: 48 or 96 kHz
Pull-Up/Down Support: No
Dante Transmitter (Output) Channels: 2
Dante Receiver (Input) Channels: 2
Dante Audio Flows: 4; 2 transmitter, 2 receiver
Internal Digital Audio Processing: 32-bit, fixed
Transmitter (Output) and Receiver (Input) Nominal
Level: –20 dBFS
Network Interface:
Type: 100BASE-TX, Fast Ethernet per IEEE® 802.3u
(10BASE-TX and 1000BASE-T (GigE) not supported.)
Power-over-Ethernet (PoE): Per IEEE 802.3af
Data Rate: 100 Mb/s (10 Mb/s and 1000 Mb/s not
supported)
Analog Microphone Input:
Compatibility: dynamic or phantom-powered
microphones
Type: balanced, capacitive coupled
Impedance: 3.6 k (3600) ohms, nominal
Gain: 20 to 65 dB in 1-dB steps
Frequency Response: 20 Hz to 22 kHz, +0/–1 dB
Distortion (THD+N): <0.0004 %, 1 kHz, –4 dBFS
output, 20 dB gain, 22 kHz BW
Dynamic Range: 120 dB, ref 0 dBFS output, 20 dB
gain, A-weighted
Phantom Power: P48 per IEC 61938 standard, on/off
selectable with status LED
Headphone Output:
Type: dual-channel (stereo)
Compatibility: intended for connection to stereo (dual-
channel) or monaural (single-channel) headphones,
headsets, or earpieces with nominal impedance of 50
ohms or greater
Maximum Output Voltage: 3.5 Vrms, 1 kHz, with load
of 150 ohms
Frequency Response (TOX Filter Disabled):
20 Hz to
20 kHz, +0/–1 dB
Frequency Response (TOX Filter Enabled):
20 Hz to
10 kHz, –3 dB at 10 kHz
Distortion (THD+N): <0.002 %
Dynamic Range: >102 dB
Remote Control Inputs: 2
Functions: configurable
Type: active low, 1 mA maximum, input pulled up to
3.3 volts DC by way of 3.4 k (3400) ohm resistor
Tally Outputs:
2
Functions: independently configurable, can follow
STcontroller On/Off buttons, Dante main transmitter
(output) status, remote control input status, or TOX
(tone receive) status
Type: active high, active low, differential – active high,
differential – active low, configurable
High Output: 100 mA maximum at 12 volts DC
Low Output: 100 mA sink
TOX (Tone Receive) Tally Activation:
Method: in-band audio tone
Source: Dante receiver (input) Headphone Ch1 or
Dante receiver (input) Headphone Ch2, selectable
Tone Characteristics: 18 to 23 kHz, nominal
Minimum Level: –25 dBFS, nominal
Detect Time: 10 milliseconds, minimum
Connectors:
Ethernet: RJ45 jack
Microphone Input: 3-pin female XLR
Headphone Output: 3-conductor (TRS) ¼-inch jack
and 3-conductor (TRS) 3.5 mm jack
Remote Control Inputs: 3-conductor (TRS) 3.5 mm
jack
Tally Outputs: 3-conductor (TRS) 3.5 mm jack
USB: type A receptacle (used only for updating
firmware)
Configuration: Studio Technologies STcontroller
personal computer application
Ethernet Control: UDP commands allow support of
remote control and status indication functions