Datasheet

Studio Technologies, Inc. Model 207 eSports Console, Issue 2, Page 4
Model 207 Specifications
Power Source:
Power-over-Ethernet (PoE): class 2 (low power, ≤6.49 watts)
Network Audio Technology:
Type: Dante audio-over-Ethernet
AES67-2013 Support: yes
Dante Domain Manager (DDM) Support: yes
Bit Depth: up to 24
Sample Rate: 44.1 and 48 kHz
Number of Transmitter (Output) Channels: 4 (Main, Talkback,
Line In L, Line In R)
Number of Receiver (Input) Channels: 4 (Headphone Ch1,
Headphone Ch2, Headphone Ch3, Headphone Ch4)
Dante Audio Flows: 4; 2 transmitter, 2 receiver
Network Interface:
Type: 100BASE-TX, twisted-pair Ethernet, Power-over-Ethernet
(PoE) supported
Data Rate: 100 Mb/s (10 Mb/s and 1000 Mb/s “GigE” Ethernet
not supported)
Compatibility – Headset A: single- or dual-ear broadcast-
style with dynamic or electret (low-voltage DC-powered)
microphone: pin 1 mic common; pin 2 mic; pin 3 phones
common; pin 4 phones left; pin 5 phones right
Compatibility – Headset B: CTIA™/AHJ configuration
(typically uses electret powered mic): tip phones left; ring 1
phones right; ring 2 common; sleeve mic
Microphone Input:
Compatibility: dynamic or electret (low-voltage DC-powered)
microphones
Type: unbalanced
Electret Microphone Power: 5 volts DC via 2.21 k resistor,
selectable on/off
Impedance: 1 k ohms, nominal, microphone power off; 690 ohms,
nominal, microphone power on
Gain: 24, 30, 36, 42, 48 dB, selectable
Frequency Response: 50 Hz to 20 kHz, +0/–2 dB
Distortion (THD+N): <0.07%, measured at –20 dBFS, 22 Hz
to 22 kHz bandwidth, 36 dB of gain
Dynamic Range: >96 dB, A-weighted, 24 dB gain
Compressor:
Application: applies to Dante main and talkback transmitter
(output) channels and sidetone audio
Threshold: 1 dB above nominal level (–19 dBFS)
Slope: 2:1
Status LED: compressor active
Headset Headphone Output:
Type: 2-channel (stereo)
Compatibility: intended for connection to stereo (dual-channel)
or monaural (single-channel) headsets with a nominal impedance
of 50 ohms or greater
Maximum Output Voltage: 3.8 Vrms, 1 kHz, 150 ohm load
Frequency Response: 20 Hz to 20 kHz, –2 dB
Distortion (THD+N): <0.002%
Dynamic Range: >100 dB
Stereo Line Input:
Type: stereo (2-channel), analog, unbalanced
Impedance: 10 k ohms, nominal
Nominal Level: –16 dBu (–18 dBV) (0.13 Vrms)
Gain: –3, 0, 3, 6, 9, or 12 dB, selectable
Frequency Response: 20 Hz to 20 kHz, +0/ –0.7 dB
Distortion (THD+N): <0.008%, measured at 0 dB gain
Dynamic Range: >105 dB, A-weighted
Connectors:
Headset A: 5-pin female XLR
Headset B: 3.5 mm 4-conductor TRRS jack, per Japanese
standard JEITA/EIAJ RC-5325A
Stereo Line Input: 3.5 mm 3-conductor TRS jack, per Japanese
standard JIS C 6560
Ethernet: Neutrik NE8FBH etherCON RJ45 receptacle
USB: type A receptacle (located inside Model 207’s enclosure
and used only for updating firmware)
Configuration: requires Studio Technologies’ STcontroller
software application, version 2.02.00 and later
Environmental:
Operating Temperature: 0 to 50 degrees C (32 to 122 degrees F)
Storage Temperature: –40 to 70 degrees C (–40 to 158 degrees F)
Humidity: 0 to 95%, non-condensing
Altitude: not characterized
Dimensions (Overall):
4.3 inches wide (10.9 cm)
2.1 inches high (5.4 cm)
5.1 inches deep (13.0 cm)
Deployment: intended for tabletop applications
Weight:
1.2 pounds (0.55 kg)
Specifications subject to change without notice.
Studio Technologies, Inc.
Skokie, Illinois USA
© by Studio Technolog
ies, Inc., June 2019
studio-tech.com