Datasheet

Model 206 Specifications
Power Source:
Power-over-Ethernet (PoE): class 2 (low power, ≤6.49 watts)
Network Audio Technology:
Type: Dante audio-over-Ethernet
AES67-2013 Support: yes
Dante Domain Manager (DDM) Support: yes
Bit Depth: up to 24
Sample Rate: 44.1 and 48 kHz
Number of Transmitter (Output) Channels: 4 (main, talkback 1,
talkback 2, talkback 3)
Number of Receiver (Input) Channels: 4 (Headphone Ch1,
Headphone Ch2, Headphone Ch3, Headphone Ch4)
Dante Audio Flows: 4; 2 transmitter, 2 receiver
Network Interface:
Type: 100BASE-TX, twisted-pair Ethernet, Power-over-Ethernet
(PoE) supported
Data Rate: 100 Mb/s (10 Mb/s and 1000 Mb/s “GigE” Ethernet
not supported)
Microphone Input:
Compatibility: dynamic or phantom-powered microphones
Type: balanced, capacitive coupled
Impedance: 3.1 k ohms, nominal
Gain: 35, 43, 52, 59 dB, selectable
Frequency Response: 25 Hz to 20 kHz, –3 dB
Distortion (THD+N): <0.018%, measured at 35 dB of gain
Dynamic Range: 98 dB, A-weighted
Phantom Power: P48 per IEC 61938 standard, on/off selectable
with status LED
Compressor:
Application: applies to Dante main and talkback transmitter
(output) channels
Threshold: 1 dB above nominal level (–19 dBFS)
Slope: 2:1
Status LED: compressor active
Microphone Output:
Type: passive via two 200 ohm resistors from microphone input
(will pass phantom power in either direction)
Muting: solid-state relay contacts, 60 dB attenuation @ 1 kHz
Headphone Output:
Type: 2-channel (stereo)
Compatibility: intended for connection to stereo (dual-channel)
or monaural (single-channel) headphones, headsets, or earpiec-
es with nominal impedance of 50 ohms or greater
Maximum Output Voltage: 3.0 Vrms, 1 kHz, 150 ohm load
Frequency Response: 20 Hz to 20 kHz, +0/–1 dB
Distortion (THD+N): <0.008%
Dynamic Range: >102 dB
Remote Control Inputs: 2
Functions: configurable to mimic the action of the main,
talkback 1, talkback 2, or talkback 3 button functions
Type: active low, 1 mA maximum, inputs pull up to 3.3 volts DC
Connectors:
Microphone Input: 3-pin female XLR
Microphone Output: 3-pin male XLR
Headphone Output: 3-conductor ¼-inch jack
Remote Control Inputs: 3-conductor 3.5 mm jack
Ethernet: Neutrik etherCON RJ45
USB: type A receptacle (located inside Model 206’s enclosure
and used only for updating firmware)
Configuration: requires Studio Technologies STcontroller
personal computer application, version 1.05.00 and later
(STcontroller compatible with Windows® version 7 and later)
Dimensions (Overall):
4.3 inches wide (10.9 cm)
2.1 inches high (5.4 cm)
5.1 inches deep (13.0 cm)
Deployment: intended for tabletop applications
Weight:
1.2 pounds (0.55 kg)
Specifications subject to change without notice.
Studio Technologies, Inc.
Skokie, Illinois USA
© by Studio Technolog
ies, Inc., April 2018
studio-tech.com
Studio Technologies, Inc. Model 206 Announcer’s Console, Issue 2, Page 5