COMPONENT SPEAKERS AND CROSSOVERS CONTENTS (Click on a topic to view) Congratulations NT-1 Tweeter Mounting Introduction Installation S t u d i o D r i v e r NT-1 Installation S t u d i o D r i v e r MW-44 FN-3 C r o s s o v e r S t u d i o D r i v e r MW-54 FN-6 C r o s s o v e r S t u d i o D r i v e r MW-64 Additional Information NT-1 Tw e e t e r A s s e m b l y Warranty
Congratulations Thank you for selecting S T U D I O D R I V E R components. Manufactured in Stuttgart, Germany, technical innovations and high-tech processes are employed throughout our manufacturing process to help ensure many years of musical enjoyment. These drivers are the end result of our commitment to the PRECISION REPRODUCTION of PURE MUSIC WITHOUT LIMIT. SERVICE: Do not attempt to service S T U D I O D R I V E R products yourself.
INTRODUCTION Your new S T U D I O D R I V E R component set is part of an exciting line of loudspeakers. They are the definitive result of years of research and development, realized by the same engineering team charged with designing audiophile quality speaker systems for a select group of high performance German automobiles, working hand in hand with our own award-winning engineering staff.
S T U D I O D R I V E R NT-1 DESCRIPTION One Inch Titanium Dome Tweeter Recommended frequency range 4 kHz - 22 kHz M E C H A N I C A L PA R A M E T E R S Normal Power Handling Fs Re Le Z Bl Diaphragm Material Voice Coil Diameter Voice Coil Former Voice Coil Length Voice Coil Layers Gap Height Sensitivity (SPL at 1W) Mms 100W rms 1600 Hz 3.4Ω .18 mH 4Ω 1.35 TM Titanium 25 mm (1”) Aluminum 1.5 mm 2 2 mm 88 dB .
STUDIODRIVER MR-44 DESCRIPTION Four Inch Aluminum Cone Midwoofer Recommended frequency range 160 Hz - 8 kHz M E C H A N I C A L PA R A M E T E R S Normal Power Handling Fs Qms Vas Cms Mms Rms Xmax Sd Dia 50W rms 78.0 Hz 2.74 2.5 Liters 0.78 mm/N 5.3 grams 0.950 kg/sec 5 mm 48.0 sq.cm 7.8 cm ELECTRICAL PA R A M E T E R S Qes Re Le Z BL 0.5 3.4 ohms .24 mH [@ 1kHz] 4.0 ohms 4.2 Tm C O M B I N AT I O N PA R A M E T E R S Qts no Sens 0.42 0.
S T U D I O D R I V E R MW-54 DESCRIPTION Five and one quarter Inch Aluminum Cone Midwoofer Recommended frequency range 90 Hz - 3.5 kHz M E C H A N I C A L PA R A M E T E R S Normal Power Handling Fs Qms Vas Cms Mms Rms Xmax Sd Dia 100W rms 62.0 Hz 4.450 6.9 Liters 0.8 mm/N 8.4 grams 0.73 kg/sec 5 mm 78.5 sq.cm 10.0 cm ELECTRICAL PA R A M E T E R S Qes Re Le Z BL 0.47 3.6 ohms .12 mH [@ 1kHz] 4.0 ohms 5.0 Tm C O M B I N AT I O N PA R A M E T E R S Qts no Sens 0.43 0.
S T U D I O D R I V E R M W-64 DESCRIPTION Six and one half Inch Aluminum Cone Midbass Recommended frequency range 70 Hz - 3.5 kHz M E C H A N I C A L PA R A M E T E R S Normal Power Handling Fs Qms Vas Cms Mms Rms Xmax Sd Dia 100W rms 57.0 Hz 4.130 18.6 Liters 0.730 mm/N 18.8 grams 0.93 kg/sec 5 mm 135.0 sq.cm 13.1 cm ELECTRICAL PA R A M E T E R S Qes Re Le Z BL 0.74 3.4 ohms .15 mH [@ 1kHz] 4.0 ohms 5.0 Tm C O M B I N AT I O N PA R A M E T E R S Qts no Sens 0.63 0.
NT-1 T W E E T E R A S S E M B LY Surface Mounting A D E B D E F C D E F Recess Mounting Recess Mounting The tweeters are equipped with wires and attached connectors. The tweeter wires are designated solid black (-), and black with a white stripe (+). Locate the corresponding spade connectors from the hardware pack and crimp them to the end of your chosen speaker wire. Attach the positive speaker wire lead to the tweeter connector with the black wire with a white trace.
N T- 1 T W E E T E R M O U N T I N G C o n f i g u r i n g t h e N T- 1 Tw e e t e r Choose the desired method of mounting the tweeters. The N T- 1 tweeters can be surface or recess mounted while allowing rotation of the tweeter within the mount for optimal imaging. Surface Mounting Locate the disk designated "E" in the tweeter assembly drawing.
I N S TA L L AT I O N M o u n t i n g C o n s i d e r a t i o n s for your Midwoofers S T U D I O D R I V E R component speakers are designed to mount into most factory speaker locations with minimum effort. The speaker baskets are designed to be a universal fit. When designing your system, a good rule of thumb is to mount the tweeter close to the midrange/midbass speaker. This usually produces the most accurate soundstage and image.
I N S TA L L AT I O N Speaker Wiring Locate the hardware pack supplied with your new component set. Inside you will find screws and crimp terminals. The midrange and midbass speakers are each equipped with a small and a large terminal. The large terminal is the positive (+) connection and the small terminal is the negative (-) connection. Find the corresponding female crimps in the hardware pack. Properly crimp these connectors to the end of your chosen speaker wire.
FN-3 CROSSOVER FN-3 2wayCrossover INPUT + - WOOFER + - TWEETER 0dB -2dB - Connect to the amplifier (+) POSITIVE speaker output This Terminal Is Not Used Connect to the amplifier (-) NEGATIVE speaker output Connect to the Tweeter (-) NEGATIVE speaker terminal Connect to the Tweeter (+) POSITIVE speaker terminal [-2dB attenuation] Connect to the Midrange (+) POSITIVE speaker terminal Connect to the Tweeter (+) POSITIVE speaker terminal [no attenuation] Connect to the Midrange (-) NEGATIVE spe
FN-6 CROSSOVER FN-6 Woofer IN + - - + Midrange -2dB 0 dB - - + -2dB Connect to the amplifier (+) POSITIVE speaker output - Tweeter 0 dB - + Connect to the Tweeter (+) POSITIVE speaker terminal Connect to the amplifier (-) NEGATIVE speaker output Connect to the Tweeter (-) NEGATIVE speaker terminal [no attenuation] Connect to the Tweeter (-) NEGATIVE speaker terminal [-2dB attenuation] Connect to the Midbass (-) NEGATIVE speaker terminal Connect to the Midrange (+) POSITIVE speaker termi
A D D I T I O N A L I N F O R M AT I O N Our dealers are trained to achieve the highest level of performance from our products. If you are installing your new component speakers on your own and need assistance, please ask your local dealer or call the S T U D I O D R I V E R Technical Service Department at 1-888-627-6937.
WA R R A N T Y Three-Year Limited U.S.A. Warranty This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. StudioDriver warrants its products to be free from defects in materials and workmanship under normal use and service for a period of three (3) years from the date of original purchase when the unit is installed by an Authorized Dealer. Non-Authorized Dealer installed products carry a one (1) year parts and ninety (90) days labor limited warranty.
