User Manual

TimeLine - User Manual
®
pg 25
MIDI Specification
CC# Value Range
KNOBS:
Type encoder 19 0-11
Time 3 0-127
Repeats 9 0-127
Mix 14 0-127
Filter 15 0-127
Grit 16 0-127
Speed 17 0-127
Depth 18 0-127
PARAMETERS:
Tap Division 21 0-4
Boost 23 0-60
Persist 22 0-1
Smear 38 0-18
High Pass 47 0-20
dTAPE - Tape Speed 58 0-1
dTAPE - Low End 59 0-20
dBUCKET - Range 45 0-1
DIGITAL - Repeat Dynamics 56 0-1
DUAL - Time 2 32 0-26
DUAL - Repeats 2 34 0-18
DUAL - Mix 2 33 0-18
DUAL - Config 36 0-1
PATTERN - Pattern 39 0-15
SWELL - Rise Time 44 0-27
TREM - Speed 61 0-34
TREM - Depth 57 0-18
TREM - LFO 29 0-4
FILTER - Q 40 0-11
FILTER - LFO 28 0-10
FILTER - Depth 41 0-18
FILTER - Speed 42 0-34
FILTER - Location 43 0-1
LO-Fi - Mix 51 0-20
LO-Fi - Vinyl 52 0-18
LO-Fi - Sample Rate 49 0-20
LO-Fi - Bit Depth 50 0-20
LO-Fi - Filter 53 0-8
ICE - Interval 30 0-29
ICE - Slice 46 0-2
ICE - Blend 25 0-20
DUCK - Sensitivity 37 0-17
DUCK - Release 55 0-20
DUCK - Feedback 54 0-1
LOOPER:
Record 87 any
Play 86 any
Stop 85 any
Reverse (toggle) 94 any
Full/Half Speeed (toggle) 95 any
Pre/Post (toggle) 96 any
Undo (to initial loop) 89 any
Redo 90 any
Looper Level 98 0-127
MIDI Patch changes:
TimeLine presets are arranged in 100 banks of 2 presets
each for a total of 200 presets. MIDI access to these
presets is available as MIDI program change messages.
Via MIDI, the presets are numbered sequentially, for
example:
BANK 00A = MIDI program # 0
BANK 00B = MIDI program # 1
BANK 01A = MIDI program # 2
BANK 01B = MIDI program # 3
BANK 02A = MIDI program # 4
etc ...
To access presets 0-127 via MIDI, send program change
messages as shown above. To access 128 to 199, first
send a MIDI Patch Bank message (CC# 0) with a value of
1, then the program change message. To switch back to
a preset from 0 to 127, send CC #0 with a value of 0, then
the program change message.
Other MIDI CC numbers:
A footswitch 80 down=0 up=127
B footswitch 82 down=0 up=127
TAP footswitch 81 down=0 up=127
Infinite Repeats 97 off=0 on=127
Remote TAP 93 any
Expression Pedal 100 0-127
Bypass 102 byp=0 eng=127
MIDI Patch Bank 0 0-1
Send a 0 value to access presets 0-127.
Send a 1 value to access presets 128-199
.
Looper MIDI control via MIDI note #’s:
The looper can also be controlled with MIDI note numbers.
Record note 0, velocity > 0
Play note 2, velocity > 0
Stop note 4, velocity > 0
Reverse (toggle) note 14, velocity > 0
Full/Half Speed (toggle) note 16, velocity > 0
Pre/Post (toggle) note 17, velocity > 0
Undo (to initial loop) note 7, velocity > 0
Redo note 9, velocity > 0
Reverse (absolute) note 103, velocity = 127
Forward (absolute) note 103, velocity = 0
Half Speed (absolute) note 104, velocity = 127
Full Speed (absolute) note 104, velocity = 0
MIDI Time Clock:
TimeLine will accept MIDI clock at the MIDI
input and sync delay time.
CC# Value Range