USER MANUAL ®
DIG - Dual Digital Delay User Manual ® Front Panel TYPE Choose from three delay conversion process choices: 24/96 – Modern, clean, and pure delay with subtle dynamics processing. adm – Early 80s adaptive delta modulation process, providing snappy, percussive delays. 12 bit – Mid 80s 12-bit conversion method yields slightly darker and warmer delays. MOD Sets the amount of modulation added to the delay lines. MIX Controls wet/dry mix for Delay 1. Full clockwise is 100% wet.
DIG - Dual Digital Delay User Manual ® Secondary Functions DELAY 1 SUBDIVISION Sets a Tap Tempo subdivision for Delay 1. Turn left for Dotted Eighth note, center for Quarter note, right for Half note. DELAY 2 REPEATS FILTER Sets the Delay 2 Repeats. Turn fully right to Track Repeats, which ties Delay 1 and Delay 2 repeats together. Sets feedback filter response. Turn left for High Cut, center for Flat response, right for Low Cut. Track Repeats is default operation.
DIG - Dual Digital Delay User Manual ® Dual Delay Config The secondary function for the MIX 2 knob sets the Dual Delay configuration. Press and hold both TAP and BYPASS footswitches while turning the MIX 2 knob to adjust. Turn left for Series, center for Ping Pong, or right for Parallel configuration. PING PONG SERIES In Series configuration, Delay 2 feeds Delay 1. This is equivalent to putting two single delay pedals in succession on your pedal board. A mono input feeds both left and right channels.
DIG - Dual Digital Delay User Manual ® Voicings 24/96 A clean, high-resolution, high-bandwidth delay with a hint of dynamics that allow the delay to sit nicely with the analog dry signal. Twenty-four bit resolution and a 96kHz sampling rate ensure uncolored, artifact-free repeats. ADM A one bit, high sample rate A/D/A conversion technique that evolved from telecommunications voice coding.
DIG - Dual Digital Delay User Manual ® Rear Panel INPUT EXP LEFT OUT RIGHT OUT 9VDC + - INPUT STEREO OUTPUTS POWER High impedance input. Default configuration is mono input. Can be used as TRS stereo input by flipping internal jumper switch. Use LEFT OUT for mono signal output. Use both outputs for stereo operation. Maximum 9 volts DC center negative, with a minimum of 250mA current. See page 10 for TRS stereo input information.
DIG - Dual Digital Delay User Manual ® Expression Input Modes The EXP jack on your DIG is set up for Expression Pedal from the factory. To change the Expression Input mode, hold down both TAP and BYPASS footswitches while powering up. While holding down, move the toggle switches to one of the three positions shown below. EXPRESSION PEDAL FAVORITE SWITCH EXTERNAL TAP Power up with both toggle switches in the UP position while both holding footswitches to configure for use with an expression pedal.
DIG - Dual Digital Delay User Manual ® Bypass Modes DIG is set up for True Bypass from the factory. To change to Analog Buffered Bypass mode with delay trails, hold down the BYPASS switch while powering up. Repeat this process to revert back to True Bypass. TRUE BYPASS BUFFERED BYPASS Our True Bypass circuit is simply a mechanical relay to switch the input signal directly to the output, with absolutely no components attached.
DIG - Dual Digital Delay User Manual ® Kill Dry Mode DIG can be set up to mute the dry signal, useful for Parallel effects loops. To change this operation, hold down both TAP and BYPASS footswitches while powering up. While holding down, turn the TIME knob to one of two ranges shown below. KILL DRY OFF Set here to disable Kill Dry. Kill Dry Off is standard operation. KILL DRY ON Set here to enable Kill Dry. This will mute the dry signal, allowing the MIX and MIX 2 controls to be used as effect levels.
DIG - Dual Digital Delay User Manual ® Circular Repeats Holding down the TAP footswitch enables Circular Repeats, where both delay lines maintain a static volume and repeat continuously until the TAP footswitch is disengaged. At this point, all previous settings will be restored. Press and hold to engage the Circular Repeats feature. Release to return the controls to their previous settings. TRS Stereo Input The 1/4” input can be set for either mono input or TRS stereo input.
DIG - Dual Digital Delay User Manual ® Sample Settings Cavernous Dotted ‘80s (FILTER) (FREE MODE) Flangetastic Pure Triplets Delicate 12 Bit Single Lead pg 11
DIG - Dual Digital Delay User Manual ® Features SOUND DESIGN • Two simultaneous, integrated delays, with unique digital rack delay voicings • Five dual delay adjustment and tone shaping knobs: Time, Time 2, Mix, Mix 2, Repeats • One modern and two classic digital delay voicings: 24/96, adm, 12 bit • Five rhythmic subdivisions: Triplet, Eighth, Golden Ratio, Dotted Eighth, Dotted Quarter • Three choices for delay line modulation: Off, Light, Deep • Secondary functions for deep control: Delay 1 Subdivision,
DIG - Dual Digital Delay User Manual ® Strymon Non-Transferrable Limited Warranty Warranty Strymon warrants the product to be free from defects in material and workmanship for a period of one (1) year from the original date of purchase. If the product fails within the warranty period, Strymon will repair or, at our discretion, replace the product at no cost to the original purchaser. Exclusions This warranty covers defects in manufacturing discovered while using this product as recommended by Strymon.
