24" 2-in-1 Foldable Pedestal Fan Owner’s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
Thank you very much for choosing a Strongway™ product! For future reference, complete the owner’s record below: Serial Number/Lot Date Code (if applicable): _____________________ Purchase Date: ____________________________________________ Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it. This fan is designed for certain applications only.
Table of Contents Intended Use .......................................................................................................................................... 4 Packaging Contents .............................................................................................................................. 4 Technical Specifications ...................................................................................................................... 4 Important Safety Information .................
Intended Use The Strongway 24" 2-in-1 Foldable Pedestal Fan easily converts from a pedestal fan to a floor fan, folding down for compact storage. It features: • Durable, rust-resistant power-coat finish • Easy assembly, tools not required • 3-speed setting • Wheels for easy mobility • Meets OSHA 1910.212(a)(5) Packaging Contents • • Fan Owner’s Manual Technical Specifications Property Specification Direct Drive Motor 120 Volts AC Maximum Current Consumption 2.
• Do not modify this product in any way. Unauthorized modification may impair the function and/or safety and could affect the life of the product. There are specific applications for which the product was designed. • Use the right tool for the job. DO NOT attempt to force small equipment to do the work of larger industrial equipment. There are certain applications for which this equipment was designed. This product will be safer and do a better job at the capacity for which it was intended.
⚠CAUTION FAN USE AND CARE • Do not force the fan. Products are safer and do a better job when used in the manner for which they are designed. Plan your work and use the correct product for the job. • Check for damaged parts before each use. Carefully check that the product will operate properly and perform its intended function. Replace damaged or worn parts immediately. Never operate the product with a damaged part. • Do not use a product with a malfunctioning switch.
• Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. • Do not place cord under furniture or appliances. Arrange cord away from a higher traffic area and where it will not be tripped over. Grounding ⚠WARNING • This machine must be grounded while in use to protect the operator from electrical shock. This unit is equipped with an electrical cord that has an equipment grounding conductor and a grounding plug.
• Grounded tools require a 3-wire extension cord. Double Insulated tools can use either a 2- or 3wire extension cord. • As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage. • The smaller the wire’s gauge number, the greater the capacity of the cord. For example, a 14gauge cord can carry a higher current than a 16-gauge cord.
Parts List Part No. 1 2 3 4 5 6 7 Description Front Guard Blade Rear Guard Motor Upper Pole Pole Support Base Quantity 1 1 1 1 1 1 1 Assembly Instructions 1. Unfold the Front Foot Cut the zip-tie and lower the front foot onto a flat, level surface. Install and tighten two of the provided threaded knobs (AA) at each side of the angle brackets on the front foot. 2. Unfold the Rear Foot Cut the zip-tie fan and rotate the rear foot onto a flat, level surface.
3. Extending the Base a) Untighten the knob (1) and slide the bar as far as it will go to the indentation (2). b) Screw the knob (1) until tight to secure the base of the fan. ⚠WARNING • This step must be completed before operating the fan in a floor or pedestal position. 4. Raise the Fan Head Untighten the triangular knob, lift up, and hold the fan head until a click or snap is heard and then stop.
5. Secure the Fan Head in Place Secure the fan head in place by tightening the triangular knob (3). . 6. Adjust the Tilt Angle Adjust the tilt angle by tightening the knob (4) in the upper pole.
Before Each Use Place the fan on a safe, flat surface where it cannot fall or be pulled by the cord. Operating Instructions ⚠WARNING • Electric shock hazard. Do not expose the unit or the plug to water or rain. Do not use the fan near a water source such as a swimming pool, bathtub, or shower. • Be sure the fan is properly grounded. • Do not use this fan with any solid-state speed control device. • Only plug the unit into a power outlet with the same voltage as rated voltage of it.
2. Transporting the Fan a) Ensure the fan is unplugged from the power source before adjusting the height or angle. b) Place the fan on a secure, flat surface where it cannot fall or be pulled by the cord. c) Fold the fan into floor mode. • Unscrew the triangle knob. • Pull the pump up and adjust the tilt angle until the fan head folds back. d) Use the wheels to move the fan. After Each Use Always turn off (0-Off) and unplug the fan after using. Maintenance 1.
Maintenance Interval Maintenance Point Depending on use, a regularly scheduled inspection should be established. Daily before operating For longer part life, after 10 hours of continuous operation, turn the fan off for 15 minutes to allow the motor to cool. After the first 20 operating hours Depending on use, a regularly scheduled inspection should be established. For longer part life, after 10 hours of continuous operation, turn the fan off for 15 minutes to allow the motor to cool.
Parts Diagram Parts List Part Number 1 2 3 4 5 6 7 Part Description Front Guard Blade Rear Guard Motor Upper Pole Pole Support Base Quantity 1 1 1 1 1 1 1 Replacement Parts • For replacement parts and technical questions, please call Customer Service at 1-800-222-5381. • Not all product components are available for replacement. The illustrations provided are a convenient reference to the location and position of parts in the assembly sequence.
Limited Warranty Northern Tool and Equipment Company, Inc. ("We'' or "Us'') warrants to the original purchaser only ("You'' or "Your") that the Strongway product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of one year from date of purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in accordance with product instructions.
Distributed by: Northern Tool & Equipment Company, Inc. Burnsville, Minnesota 55306 www.northerntool.
