LED TV with DVB-T2/C/S2 SRT40FC4003 User Manual Bedienungsanleitung Manuel utilisateur Manuale utente Manual do Utilizador Инструкции за употреба Руководство пользователя Посібник користувача Användar Manual Uživatelská příručka Navodila za uporabo Korisnički priručnik Uputsvo za rukovanje Používateľská príručka Használati útmutató Käyttöohje Brukermanual Manual del Usuario Gebruiksaanwijzing Brugervejledning Manual de Utilizare Instrukcja obsługi
Fig. 1a 10 cm Fig. 1b Fig. 1c Fig.
Fig. 3a CI+ SAT IN ANT/CABLE IN 1 Fig. 3b 2 3 AV IN HEADPHONES 4 5 SCART HDMI 1 (ARC) HDMI 2 VGA USB S/PDIF (coax.) 1 2 3 4 5 6 Fig. 4 Fig. 5 Fig. 6 2 Pause Fig. 7 2 Pause Fig. 8 5 FB 6 FF { } 3 Prev. Next Stop 5 FB 6 FF { } 3 Prev. Next 1 { } 3 Play Prev. Next Stop Repeat All Zoom In Zoom Out Move View 90° 90° Rotate Rotate AB Repeat All Set A Playlist Info. Aspect Ratio Stop Repeat All Repeat All Playlist Info.
www.strong.tv Supplied by STRONG Austria Represented by STRONG Ges.m.b.H. Teinfaltstraße 8/4. Stock 1010 Vienna, Austria Email: support_at@strong.
English Licenses THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND NONCOMMERCIAL USE OF A CONSUMER TO (i) ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD (“AVC VIDEO”) AND/OR (ii) DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE AVC VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C.
To obtain the best performance and safety, please read this manual carefully. Please keep this manual for future reference. TABLE OF CONTENTS 1.0 INSTRUCTION 1.1 Safety Instructions 1.2 Storage 1.3 Accessories 1.4 Equipment set-up 3 3 4 4 4 2.0 INSTALLATION 2.1 Default PIN code: 0000 2.2 Front panel/underside 2.3 Rear panel 2.4 Side panel 2.5 Remote control 2.6 Installing the batteries 2.7 Using the remote control 5 5 5 5 5 6 7 7 3.0 FIRST TIME INSTALLATION 3.1 DVB-S/S2 installation 3.
English 1.0 INSTRUCTION 1.1 Safety Instructions Read all of the instructions before operating the set. Keep these instructions well for later use. Only use attachments/accessories specified or provided by the manufacturer (such as the exclusive supply adapter, battery etc.). Please refer to the information on the exterior back enclosure for electrical and safety information before installing or operating the apparatus.
WEEE Directive Correct Disposal of this product. This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased.
English 2.0 INSTALLATION 2.1 Default PIN code: 0000 2.2 Front panel/underside Fig. 2 NOTE: 1. 2. 3. 4. The graphics are for representation only. Power indicator /remote sensor Speakers Buttons: Input source, Menu, V-/V+, CH-/CH+, Standby/ON. Power switch ON/OFF 2.3 Rear panel NOTE: The graphics are for representation only. Fig. 3a 1. SAT IN 2. ANT/CABLE IN 3. CI+ 4. AV IN 5. HEADPHONES Connect a satellite dish to the TV for searching programmes.
6. S/PDIF (coax. output) Use an RCA cable to connect your TV to a compatible digital amplifier or Home theatre set. 2.5 Remote control Fig. 4 1. ! 2. q 3. (ASPECT) 4. SOUND 5. (PICTURE) PIC 6. EPG 7. 0 ~ 9 8. LIST 9. 9 10. SUB 11. TEXT 12. SIZE Press to mute or restore the volume. Press to turn the TV on or standby. Change aspect ratio. Change sound mode. Change picture mode. Press to display the current EPG information in DTV mode. Choose channel directly. Press to enter into the channel list.
English 36. 7 Press to play the previous file. 37. 8 Press to play the next file. 38. 6 Press to fast forward. 39. 5 Press to fast reverse. 40. COLOUR BUTTONS Press to execute the prompt function in TV or DTV menu mode. 2.6 Installing the batteries Fig. 5 Place 2x AAA batteries in the battery compartment of the remote control. Make sure to match the polarity markings inside the compartment. NOTE: Pictures are only for reference. Actual items may differ. 1. Slide the cover horizontally. 2.
Scan type Select which input source you want to use: DVB-S to receive satellite broadcasts (and if you are equipped with a satellite dish), DVB-T to receive terrestrial broadcasts or DVB-C to receive cable broadcasts. 3.1 DVB-S/S2 installation Satellite Setting First select the region where you are using the TV. This important to set time zone correct. Use the t upq and confirm with OK. Press pq to highlight the satellite your dish is aimed at. Confirm with OK to mark the satellite.
NOTE: English Please check the settings for your cable system used by your provider! Press OK to continue. Crypted Select FTA Channels to search Free-To-Air channels only or All Channels to search FTA and encrypted channels Press pq t u to highlight the country that you want to install, then press OK to start searching. 4.0 ELECTRONIC PROGRAMME GUIDE (EPG) EPG stands for Digital Electronic Programme Guide. It is supplied by the programme providers and offers information on broadcasted programmes.
Colour Adjust the saturation of the colour based on your own preference. Tint No function Sharpness Adjust the peaking in the detail of the picture. 5.2.2 Colour Temperature In this menu you can change the overall colour cast of the picture. Press pq to select Colour Temperature, then press OK to enter a sub-menu. Press pq to select the relevant picture effect (DEFAULT: Cold Normal Warm). Cold lncrease the blue tone for the white. Normal Increase the neutral colours for the white.
English Press OK to adjust. After finish your adjustment, press OK to save and return to the previous menu. Below items depend if they are available of select input source. Use INPUT to select another source. 5.4.1 Auto Tuning Press pq to select Auto Tuning, select the Scan Type and proceed with OK. 5.4.2 Dish Setup If you use DVB-S/S2 as input source, the Dish Setup menu allow you to set you satellite and belonging settings as DiSEqC port and LNB type.
NOTE: To modify the order of the channels contained in the channel list do as follow: press Menu and OK to select Program Edit (it is also possible access this option by pressing PROG button on the remote control). To move a channel, select it by using pq or CH +/- button then press YELLOW button. Now, there are two different ways to move the channel: Enter the number of the new position by using the 0 ~ 9 buttons on the remote control and confirm with OK or YELLOW.
Press pq t u to select your chosen Subtitle Language, then press OK This item shows the region you been selected by first time you install the TV. Restore Factory Default Press pq to select this function, by pressing OK and enter the PIN code. You will reset all the settings contained in the main menu and deleted all installed channels. TV will go back to First Time Installation See chapter 3. Version Information Your current software version is displayed. HDMI CEC See chapter 5.7.1.
This TV may not support some multimedia files changed and upgraded as the change of the encoding format or other technical aspects advances. Please refer to chapter 9. Appendix for a list of supported file formats for USB playback. 6.2 USB menu Press SOURCE and select USB. You can view movie, music and photo files from your USB storage devices. Connect a USB storage device to the USB input terminal and select the types of media on the home page: Movie, Music, Photo and text.
Highlight the icon and press OK. You can select 3 different modes: None to disable the function, 1 to repeat one track only and All to repeat the entire list once it is finished. Information Highlight the icon and press OK to check the information of the playing music. NOTE: If one (or more) file(s) of the play list is selected, the buttons 7 8 will play only selected files. This menu only shows supported files.
6.2.4 Browse text documents Press t u to select Text in the main menu. Then press t u to select the drive disk you choose to watch and OK to enter. Select the file you want to display by using pq t u and confirm with OK. Quit step by pressing OK. Press t u to select return and go back to previous menu. 6.2.5 Software update via USB From time to time you can check if there is an improved software version available. This can be viewed and downloaded from our website www.strong.tv.
Radio frequency interference Possible cause and solution If the antenna is located in the fringe area of a television signal where the signal is weak, the picture may be marred by dots, show blocking or break-ups. When the signal is extremely weak, it may be necessary to install a special antenna to improve the reception. English Problem Snowy dots, blocking and interference 1. Adjust the position and orientation of the indoor/outdoor antenna. 2. Check the connection of the antenna. 3.
8.0 SPECIFICATIONS Audio Audio Output: 8W Video Channel coverage: System: DVB-T2: 174 MHz-230 MHz; 470 MHz-860 MHz DVB-C: 50-858 MHz DVB-S2: 950 MHz-2150 MHz DTV: DVB-T2, DVB-S2, DVB-C ATV: PAL/SECAM (BG/DK/1) AV: PAL, NTSC Connectors 1x ANT/CABLE IN 1x SAT IN 1x SCART 1x CI+ 2x HDMI 1x S/PDIF (coax.
