Picture similar Digital High Definition Terrestrial Receiver SRT 8101/8105 User manual Manuel d’Utilisateur Manuale Utente Manual del usuario Manual do Usuário Felhasználói kézikönyv Instrukcja obsługi Руководство пользователя
Table of Contents 07 Oct 2011 19:20 1.0 Introduction 1.1 Safety Instructions 1.2 Storage 1.3 Equipment Set-up 1.4 Accessories 1.5 Usage of external USB devices 2.0 Your Receiver 2.1 PIN-CODE DEFAULT: 0000 2.2 Front Panel 2.3 Rear Panel 2.4 Remote Control 3.0 Connection 3.1 Connecting to a Terrestrial Antenna 3.2 Connecting to TV with HDMI cable 3.3 Connecting to TV with SCART cable 3.4 Connecting to TV with Cinch cable 3.5 Connecting to a Digital Audio Amplifier with S/PDIF 3.
PART 1 • English 1.0 Introduction 1.1 Safety Instructions DO NOT INSTALL YOUR RECEIVER: In a closed or poorly ventilated cabinet; directly on top of or under any other equipment; on a surface which might obstruct the ventilation slots.
PART 1 • English 1.3 Equipment Set-up English We recommend you consult a professional installer to set up your equipment. Otherwise, please follow the instructions below: Refer to the user manual of your TV and antenna. Make sure that the HDMI cable and outdoor components are in a good condition. Use only a HDMI 1.3 cable or higher for maximum performance. If you use TV SCART connection, use then well shielded SCART cable (applies only to SRT 8105).
PART 1 • English 1. 4 digits display: Indicates current time in STAND-BY mode* Indicates current channel number in OPERATING mode* 2. USB: Connector for USB devices. 3. IR sensor: Point your remote control towards this sensor. 4. Mode indicator: RED indicates that the receiver is in STAND-BY mode. GREEN indicates that the receiver is in OPERATING mode. *Only SRT 8105 2.3 Rear Panel Fig. 2 1. ANT IN To connect to your antenna for the reception of broadcast signal. 2.
PART 1 • English English 17. AUDIO Sets the current audio channel to left, right or stereo 18. TV/RADIO Toggles between TV or RADIO mode 19. FAV Favourite group selection 20. FILE Shows the Media Player list 21. TTX Shows Teletext on OSD (On Screen Display) 22. SUBTITLE Shows list of subtitled languages 23. 5 6 Fast rewind / Fast forward 24. Coloured buttons for Multimedia and Teletext functions 3.0 Connection 3.
PART 1 • English By connecting your receiver to the latest digital amplifiers or home theatre systems with HDMI connections, you will enjoy the best possible sound quality and multi-channel audio (depending on broadcast). Connect the HDMI output of the receiver to an input of your amplifier, and then connect the HDMI output of the amplifier to your TV set. Select the correct input on your amplifier to watch and listen to programmes. 3.7 Connecting a USB storage device Fig.
PART 1 • English English Channel No.: Select a channel that is known to carry a broadcast in your region. The Signal Strength and Signal Quality bars give a visual indication of the reception. Adjust your antenna to obtain maximum signal strength and quality. Once all settings are made, press OK to start scanning. The receiver will now search for all available channels. Once scanning is finished, the receiver switches to viewing mode.
PART 1 • English TIP: Use tu to toggle between the All Channel list and favourite lists or press FAV for a list of available favourite lists. 6.1.3 Using the pq or PG+/PG- keys p switches to the next channel. q switches to the previous channel. PG+ switches to the next 10 channels. PG- switches to the previous 10 channels. 6.2 Info Banner While watching TV you can press the INFO button any time to get information about the current channel and event*.
PART 1 • English The Electronic Programme Guide is a very useful function that allows you to view event schedules and information and to mark programmes for recording. To access the EPG, press the EPG button in viewing mode. Use pq to select the desired channel and tu to select the desired event. Press OK to display detailed information on the selected event. Use EXIT to quit the detailed information screen. Press RED to get to the Step Time function. Use tu to select the desired step and OK to execute it.
PART 1 • English Once all changes are made, press EXIT twice. A confirmation banner will pop up. Select Yes to save the changes or No to discard. 7.1.1.2 Locking channels Locked channels can only be watched after entering the pin code. (DEFAULT PIN: 0000) To lock or unlock a channel, press RED while in TV Channel List. The red Lock sign on the top of the screen will move up to indicate that the Lock function is selected. Use pq to select the desired channel and press OK to lock or unlock it.
Rename Press GREEN in Edit Channel to enable the Rename function. The Rename sign will move up to indicate that Rename is selected. Use pq to highlight the desired channel and press OK to select it. A text field will now pop up at the right of the screen. Use tu pq to select the desired characters and enter them with OK. Once you have finished editing, press BLUE to enter the changes. Once all changes are made, press EXIT twice. Select Yes to save the changes or No to discard.
PART 1 • English 7.2.3 Antenna Adjustment Use pq to select Installation, press OK or u to advance. Use pq to select Aerial Adjustment and press OK to enter. Use pq move the highlight to the setting you wish to alter and use tu to change values. The following settings are available: Antenna Power: Set to On if you use an active antenna. When set to On, 5 V will be present on the ANT IN connector of the receiver. Select Off for passive antennas.
Aspect Mode: Use this option to select the aspect ratio of your TV and the preferred conversion method. Options are: Auto (automatic detection of aspect ratio), 4:3 Panscan (Displays 16:9 widescreen broadcasts full screen on your 4:3 TV), 4:3 letterbox (black bars on top and under the picture on a 4:3 TV) and 16:9 (use this setting for 16:9 TV sets). Connection: Use this option to select the connection to your TV set. Select HDMI or TV SCART.
PART 1 • English 7.3.5 Parental Lock This menu allows you to protect the installation menu and/or channels with a password. You can also enter a new password in the Parental Lock menu. Use pq to select Parental Lock from the System Setup menu and press OK to proceed. You will be asked to enter your pin code. (DEFAULT: 0000) Menu Lock: Locks the installation menu. You can set Menu Lock to On or Off. Channel Lock: Choose between: Off, AGE 10, AGE 12, AGE 16 and AGE 18.
PART 1 • English 7.4.2 Load Factory Setting English This option allows you to reset the receiver to factory settings, which clears all stored channels. Warning! By resetting your receiver to factory default, all your settings and stored channels will be permanently deleted. Please use this option with care. Use pq to select "Load Factory Setting" in the Tools menu and press OK. You are asked to input password. Input the correct password using the 0~9 buttons (default: 0000).
PART 1 • English 7.5 Games Your receiver is equipped with two games which can be played on your TV screen using the receiver remote control. Use pq to select Game from the Main menu and press OK or u to proceed. Select one of the available games (Othello or Sudoku) using pq and press OK to start the game. Follow the directions on screen. Use EXIT to quit a game. 7.
PART 1 • English English Select DVR HDD Information from the Media+ menu and press OK to enter. Press EXIT to leave. 7.6.4 HDD Format The HDD format menu allows you to format the connected USB device. Warning! Formatting will permanently delete ALL data stored on the connected device. Please make a backup copy of all data you wish to keep before entering the HDD Format menu. STRONG cannot be held responsible for loss of data from USB devices used with this receiver.
PART 1 • English Problem Possible cause LED indicator not lit Mains lead unplugged Check mains plug No signal found Aerial is disconnected Aerial is damaged/misaligned Out of digital signal area Active antenna requires to switch ON antenna power/ external power Check aerial lead Check aerial Check with dealer Switch receiver’s Antenna Power ON/connect external power No picture or sound on TV HDMI is not selected on your TV or Amplifier or is set to higher resolution as TV supports TV is not switch
PART 1 • English English Audio Decoder: Audio support: AAC/DD+/AC3/PCM MPEG MusiCam Layer 2 Sampling rate: 32, 44.
PART 1 • English 20
