Picture similar Digital High Definition Terrestrial Receiver SRT 8105 ECO User manual
Table of Contents 18 Jan 2012 17:30 1.0 Introduction 1.1 Safety Instructions 1.2 Storage 1.3 Equipment Set-up 1.4 Accessories 1.5 Usage of external USB devices 2.0 Your Receiver 2.1 PIN-CODE DEFAULT: 0000 2.2 Front Panel 2.3 Rear Panel 2.4 Remote Control 3.0 Connection 3.1 Connecting to a Terrestrial Antenna 3.2 Connecting to TV with HDMI cable 3.3 Connecting to TV with SCART cable 3.4 Connecting to TV with Cinch cable 3.5 Connecting to a Digital Audio Amplifier with S/PDIF 3.
PART 1 • English 1.0 Introduction 1.1 Safety Instructions DO NOT INSTALL YOUR RECEIVER: In a closed or poorly ventilated cabinet; directly on top of or under any other equipment; on a surface which might obstruct the ventilation slots.
PART 1 • English 1.3 Equipment Set-up Warning: Indicates warning information. Tips: Indicates any other additional important or helpful information. MENU Move to Represents a button on the remote control or the receiver. (Bold Character) Represents a menu item within a window. (Italic Character) English We recommend you consult a professional installer to set up your equipment. Otherwise, please follow the instructions below: Refer to the user manual of your TV and antenna.
PART 1 • English 2. USB: Connector for USB devices. 3. IR sensor: Point your remote control towards this sensor. 4. Mode indicator: RED indicates that the receiver is in STAND-BY mode. GREEN indicates that the receiver is in OPERATING mode. 2.3 Rear Panel Fig. 2 1. ANT IN To connect to your antenna for the reception of broadcast signal. 2. TO TV To connect to the terrestrial antenna input of your TV set. This connection will allow you to watch analogue terrestrial programmes via the tuner in your TV.
PART 1 • English Shows list of subtitled languages Fast rewind/Fast forward For Multimedia and Teletext functions English 22. SUBTITLE 23. 5/6 24. Coloured buttons 3.0 Connection 3.1 Connecting to a Terrestrial Antenna Fig. 4 To receive broadcast signal, your terrestrial indoor or outdoor antenna must be connected to the ANT IN connector on the back of the receiver. Use a properly shielded antenna cable and suitable connectors.
PART 1 • English 3.7 Connecting a USB storage device Note: Fig. 5 We recommend the use of a hard disk drive USB 2.0 or higher for recording and play back of TV events. For proper functioning of Time Shift and recording functions, a fast USB device (such as a hard disk drive) is needed. Interrupted playback or a distorted picture during playback or Time Shift are indications for a low device speed. STRONG cannot guarantee proper functioning of recoding and or Time Shift functions with all USB devices.
TIP: In case the Welcome “Easy install” menu does not appear after switching on the receiver the first time, reset the receiver to factory settings by pressing the MENU button and selecting Load Factory Setting in submenu Tools. (Default PIN 0000) 5.0 Quick guide to using your receiver We at STRONG understand that you can’t wait to enjoy your new high definition digital terrestrial receiver. The following quick guide will make you familiar with the basic operation of this device.
PART 1 • English 6.2 Info Banner While watching TV you can press the INFO button any time to get information about the current channel and event*. Press INFO twice for extended EPG details about the current channel. Press INFO three times for technical details about the current channel. *Event information is displayed when available. Availability depends on broadcast. 6.3 Selection of audio language Some channels support a choice of audio formats and/or languages.
PART 1 • English Your new receiver allows you to make an instant recording of the programme you are watching. Simply press 4 to start the recording. To enter the duration for the recording, press 4 again. Use the 0~9 keys to input the desired recording time. During the recording a recording sign will be shown on the upper right of your TV screen. To stop the recording, press 3. Select Yes and press OK again to stop the recording.
PART 1 • English 7.1.1.3 Skipping channels Channels marked with Skip will be skipped when zapping channels with the p/q buttons. Despite that, these channels are still available from the channel list. To mark channels for skipping, press GREEN while in TV Channel List. The Skip symbol on the top of the screen will move up to indicate that the Skip function is selected. Use p/q to select the desired channel and press OK to mark or unmark it for skipping.
PART 1 • English Basically, the operation of the Radio Channel List is the same as in the TV Channel List. The only difference is that in Radio Channel List there is no video information, so it will always display the radio logo at the right preview screen. 7.1.3 Delete all Use this menu to delete all stored channels. Select Delete All with p/q and press OK. The receiver asks you to enter the pin code. (Default pin :0000).
PART 1 • English 7.2.4 LCN (Logical Channel Numbering) If LCN (Logical Channel Numbering) is activated and an LCN signal is provided by the operator, channels will be stored in an operator defined order. Set LCN to On to activate operator defined channel numbering or Off to store channels in found order. 7.3 System Setup This menu allows you to manage the system settings of your receiver.
Summer Time: Date: Time: increasing by half hours progressively. The cities matching the set GMT Offset are displayed at the bottom of the screen. Select Off or On to add one hour extra for summer time during the summer. Date and Time settings are available only when GMT Usage is set to Off. Use the 0~9 buttons to enter the date. Press EXIT to proceed. Date and Time settings are available only when GMT Usage is set to Off. Use the 0~9 buttons to enter the time. Press EXIT to proceed. 7.3.
PART 1 • English 7.3.7 Favourite This menu allows you to personalize the names of the 8 available favourite lists. Use p/q to select Favourite from the System Setup Menu and press OK to proceed. The names of all groups are now displayed. Select the desired favourite group with p/q and press OK to edit its name. A text field will now pop up at the right of the screen. Use t/u p/q to select the desired characters and enter them with OK. Once you have finished editing, press BLUE to save the changes.
PART 1 • English This feature allows you to upgrade your receiver’s software via the USB port. If new software is available for your receiver, it can be downloaded from our website www.strong.tv.Place the software file (unzipped) in the root directory of your USB storage device (HDD, memory stick etc.) and insert this device into the USB port of the receiver. Select Upgrade by USB from the Tools menu and press OK to proceed. The upgrade menu will now be displayed.
PART 1 • English Use p/q browse the connected USB device and use OK to open maps. Press OK to play the highlighted selection. The help banner at the bottom of the screen explains all buttons used in the Media player. Press EXIT to quit. Note: You can also access the Media Player from viewing mode with the FILE key on the remote control. 7.6.2 Record Manager The Record Manager gives you access to previously recorded events. Select Record Manager from the Media+ menu and press OK to enter.
PART 1 • English This menu allows you to make settings for Time Shift, recording and playback. Select DVR Configuration from the Media+ menu and press OK to enter. Use p/q to move the highlight and t/u to change settings. Press EXIT to quit. Time Shift: On or Off. When Time Shift is set to Off, Time Shift becomes inactive. Time Shift to Record: On or Off. When set to On, Time Shift is also possible during record. Record Type: TS or PS.
PART 1 • English 8.0 Troubleshooting There may be various reasons for abnormal operation of the receiver. Check the receiver according to the procedures shown below. If the receiver does not work properly after checking it, please contact your dealer or the local Service Hotline. Do NOT try to open or disassemble the receiver. It may cause a dangerous situation and warranty will be void.
PART 1 • English Demodulator Demodulator: Transmission mode: Video Decoder Profile level: Video resolutions: Decoding & Video out: Aspect ratio: Audio Decoder Audio support: MPEG MusiCam Layer II Sampling rate: Audio mode: English 9.0 Technical Specifications COFDM; 16 QAM/64 QAM, QPSK 2K-8K MPEG-2 MP@ML, AVC/H264HP@L4.1, MPEG-4 ASP supported 576i/576P/720P/1080i/1080P PAL 4:3 Letterbox, 4:3 Pan & Scan, 16:9, Auto AAC/DD+*/AC3/PCM 32, 44.
PART 1 • English General Data Supply Voltage: Power Consumption: Power consumption in Standby: Operating Temperature: Storage Temperature: Operating Humidity Range: Size (WxDxH) in mm: Net-weight: 20 220 - 240 V AC (SMPS), 50/60 Hz 5.65 W (typ.), 12.00 W (max) 0.82 W 0 ~ 40 °C -30 ~ 80 °C 10~85%, RH, Non-condensing 188 x 135 x 44 0.
