Picture similar Digital High Definition Satellite Receiver SRT 7500 User Manual
PART 2 • English 1.0 Introduction 1.1 Safety Instructions 1.2 Storage 1.3 Equipment Set-up 1.4 Features & Accessories 2 2 3 3 3 2.0 YOUR RECEIVER 2.1 Front Panel 2.2 Rear Panel 2.3 Remote Control Unit 2.4 DEFAULT PIN-CODE: 0000 4 4 4 4 5 3.0 CONNECTIONS 3.1 Connecting to Satellite Dish 3.2 Connecting to TV 3.3 Connecting to Digital Audio Amplifier 3.4 Connecting to computer by serial cable 5 5 5 5 5 4.0 STARTING UP FOR THE FIRST TIME 4.1 Language Selection 4.2 Country Selection 4.
PART 2 • English 1.0 Introduction 1.1 Safety Instructions The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of not isolated dangerous voltage with the inside of the product that may be of sufficient magnitude to constitute a risk of electric shock to persons.
PART 2 • English Apparatus - shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. Where the mains plug or all-pole mains switch is used as the disconnect device, the disconnect device shall remain readily operable. 1.2 Storage 1.3 Equipment Set-up We recommend you consult a professional installer to set up your equipment. Otherwise, please follow the instructions below: Refer to the user manual of your TV and your antenna.
PART 2 • English Accessories: 1 x Remote control 2 x AAA Batteries 1 x HDMI cable 2.0 YOUR RECEIVER 2.1 Front Panel Fig. 1 1. STANDBY/ON: Set receiver to Standby or ON mode. 2. MENU: Access to the Main menu 3. BACK: Viewing mode: remove appearing messages. In Menu mode: go to previous screen or menu. 4. OK: Viewing mode: enter the channel list; another pressing on selected channel will switch back to viewing mode. In Menu mode: enter selected submenus and confirm settings. 5.
PART 2 • English 23. FRW: 24. FF: 25. TIMERS: 26. LIB: 27. PLAY: 28. STOP: 29. PAUSE: 30. RECORD: No function No function To access directly to timer menu No function Used for media player function Used for media player function Used for media player function; in viewing mode access to zoom menu No function English 2.4 DEFAULT PIN-CODE: 0000 3.0 CONNECTIONS 3.
PART 2 • English 4.2 Country Selection Select the desired country by using tu and press OK to continue. 4.3 Antenna Installation In the Antenna Installation Menu the necessary settings for the dish installation will be displayed. Depending on the selected country there might have been already done a setup for your satellite dish (Austria and Germany: Astra 19.2E on DiSEqC input 1/ Czech and Slovakia: Astra 23.5E on DiSEqC input 1). These settings will allow you to receive signal automatically.
PART 2 • English symbol next the channel name. After you have marked all channels for locking, your changes will be saved by pressing BACK. Now you will have to enter your PIN every time you are switching to a locked channel. If you are not entering the PIN, the receiver will show after a few seconds the picture of the last watched channel until you enter the correct PIN. For more information, please refer to “Parental Settings” in chapter 5.4 CONFIGURATION.
PART 2 • English positions and align your dish until signal strength and quality range are satisfying again and store this position. Now if you setup this specific SAT position correctly, you can apply realignment on the others by pressing OK at recalculate positions. Note in order to avoid mechanical damage of your dish, please make sure the east and west limits in your motor are set correctly and dish would not hit any objects on its movement. 5.3.1.
PART 2 • English 5.3.2 FIRST TIME INSTALLATION In this menu you have the possibility to do First Time Installation, which clears all stored channels in the channel list and all settings in your setup. Then a warning message will be displayed. There select YES if you want to delete or NO to cancel. After confirming OK to reset receiver, First Time Installation Menu will be displayed. With BACK you can always cancel actions and exit the actual menu or submenu. 5.3.
PART 2 • English 5.4 Configuration In this menu you can set up your personal preferences for below adjustments. Use the pq for navigation and tu buttons to change settings. For entering values use the NUMERIC buttons. With BACK you can always cancel actions and exit the actual menu or submenu.
PART 2 • English SOKOBAN: Use pq and tu to move the little girl and boxes. Press the RED button to cancel the last move. With BLUE button you can restart the game. 5.7 Media Browser Use this menu to play MP3 and JPEG files from a USB Memory device like memory stick, digital camera or multiple card reader etc. By connecting a USB memory device the receiver recognizes it automatically and displays the valid files. Note Some compliant USB memory devices may not be supported.
PART 2 • English Press GUIDE button in viewing mode to access the EPG Menu. The screen is divided into 3 main parts: at the left side the channel list is shown, at the right the program schedule list and in the upper part a short program description with program start/end time of the current channel. With BACK you can always cancel actions and exit the actual menu or submenu. In channel list: Use pq to choose the channel. Furthermore you can use the RED/GREEN buttons to scroll through the channel list.
PART 2 • English 6.3.2 Audio Mode and Language Press A.FORMAT button in viewing mode. Further pressing will change audio channel between Left, Right and Stereo. Press the LANG button to select one of the available audio languages. 6.3.3 Video Format Press the V.FORMAT button in viewing mode. Further pressing will change the HDMI resolution. You will only see differences if you are connected via HDMI. 6.3.4 Teletext 6.3.5 Subtitles Press SUBT button in channel view mode.
PART 2 • English A.2 SPECIFICATIONS Demodulator Demodulation: QPSK, 8PSK Input symbol rate: DVB-S QPSK: 1 ~ 45 Ms/s DVB-S2 8PSK/QPSK: 10~30 Ms/s FEC decoder: Auto, 1/2, 2/3, 3/4, 5/6, 7/8 in DVB-S mode Auto, 1/2, 3/5, 2/3, 3/4, 4/5, 5/6, 8/9, 9/10 in DVB-S2 mode Auto, 3/5, 2/3, 3/4, 5/6, 8/9, 9/10 in 8PSK mode Video Decoder Profile level: MPEG-2 MP@ML, MP@HL, MPEG-4 H.264/AVC Input rate: Max.
APPENDIX APPENDIX APPENDIX: Installation assistance A1
APPENDIX A2z
APPENDIX APPENDIX A3
