Picture similar Digital Terrestrial Receiver SRT 5302 User manual Bedienungsanleitung Manuel d’utilisation Manuale utente Manual del usuario Návod k obsluze Upute za korištenje
HOTLINE 0820 400 150 AT support_at@strong.tv 029 928 FR 0826 support_fr@strong.tv € 0,12/Min. österr. Festnetz € 0,15 par mn poste fixe en France 32 634451 BG +359 support_bg@strong.tv 1 445 26 10 CEE +36 support_hu@strong.tv IT 199 404 032 support_it@strong.tv Da rete fissa 24,8 cent. al min. 12,5 cent. scatto alla risposta Da rete mobile max 49 cent. al min. 15,6 cent. scatto alla risposta 501 49 91 DE 0180 support_de@strong.tv NL € 0,14/Min. deutsches Festnetz € 0,42/Min. max.
PART 1 • English 01 Jul 2013 16:46 1.0 Instruction 1.1 Safety Instructions 1.2 Storage 1.3 Equipment Set-up 1.4 Accessories 1.5 Usage of external USB devices 2 2 3 3 4 4 2.0 Connection 2.1 Connecting to TV and Terrestrial Antenna 2.2 Connecting to a Digital Audio Amplifier 4 4 4 3.0 Your Receiver 3.1 Front Panel 3.2 Rear Panel 3.3 Remote Control 3.4 Default PIN code: 0000 4 4 4 5 5 4.0 First Time Installation 6 5.0 Main Menu 5.1 Channel 5.2 Installation 5.3 Setup 5.4 Tools 5.
PART 1 • English 1.0 Instruction 1.1 Safety Instructions The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of not isolated dangerous voltage with the inside of the product that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Heat – Never use or store this product near any heat source such as a radiator heat register, stove, or any type of equipment or appliance that generates heat, including stereo amplifiers. Servicing – Refer all servicing to qualified personnel. Attempting to remove the covers or disassemble the product, could expose you to dangerous high voltage points.
PART 1 • English 1.4 Accessories 1 User Manual 1 Remote control unit 2x Batteries (AAA type) Note: The batteries should not be recharged, disassembled, electrically shortcircuited or be mixed or used with other types of batteries. If rechargeable accumulators instead of batteries are going to be used, we recommend using (e.g. NiMH) types with low self-discharge to ensure long time operation of remote control. 1.5 Usage of external USB devices It is recommended to use USB 1.1 or 2.
PART 1 • English 3.3 Remote Control English 1. ANT IN To connect an antenna for reception of broadcasting signal. Active antennas can be supported with max. 5 V/50 mA DC. 2. TO TV To connect a TV set or to connect an extra receiver. 3. S/PDIF Coaxial To connect your receiver to digital audio amplifier. 4. TV SCART Connector To connect your receiver with your TV set using a SCART cable. 5. Power Cord Your receiver requires a voltage of 220 – 240 V AC (Autoselectable), 50/60 Hz +/-5 %.
PART 1 • English 4.0 First Time Installation When using the receiver for the first time, the Easy Install menu appears. Use qp to select Region, OSD Language, Antenna Power and Scan Mode and tu to select options. Then use the qp buttons to move the focus to Search and press OK to proceed with the automatic channel scan. 5.0 Main Menu In viewing mode press MENU at any time to enter the Main Menu. It consists of the following submenus: Channel, Installation, Setup, Tools and Media+ 5.1 Channel 1.
PART 1 • English 5.1.1.2 Find English Press the button 2 in to enter the Find menu. Use the qptu buttons to highlight letters or numbers and press OK to insert. After each character, the channel list will search the channel according to your input and list the matching channel. Press EXIT to quit the Find mode. 5.1.1.3 Sort Press the button 3 to enter the Sort menu. Use the qp buttons to highlight the sorting option of your choice and press OK to confirm.
PART 1 • English 5.2 Installation 5.2.1 Auto Scan 1. Use the qp buttons to select Installation and press OK to enter the menu. 2. Use qp to select Auto Scan and press OK to enter the menu. 3. Change the Scan mode with tu. Use qp to highlight Search and press OK to start auto scan. 5.2.2 Channel Scan 1. 2. 3. 4. Use the qp buttons to select Installation and press OK to enter the menu. Select Channel Scan with qp and press OK to enter. Use the tu buttons to select scan mode – By Channel or By Frequency.
PART 1 • English 5.3.2 Subtitles preference English This menu allows you to set the preferred Subtitles Language and to switch Subtitles Type between Normal and Hard of Hearing. 5.3.3 TV System This menu allows to setup different settings concerning your TV set. Display Mode: PAL/NTSC/AUTO Aspect Ratio: Use this menu to configure the screen aspect. Possible settings are: 4:3PS (Pan&Scan), 4:3LB (Letter Box), 16:9 (Wide Screen) and AUTO.
PART 1 • English OSD Transparency: To set the OSD transparency from Off ~ 50%. OSD Timeout: To define how long the information banner is to be shown (5S~10S) Load Default OSD Setting: To clear all OSD settings and reset to default value. 5.3.7 Parental Lock This menu allows you to protect the installation menu or channels with a password. You can also change the password here. When entering the menu you will be asked to input the password (default: 0000). Menu Lock: Locks the installation menu.
PART 1 • English English 1. Enter the Tools menu, select Load Factory Default and press the OK button. You are asked to input your password. 2. Input the correct password using the numeric buttons (the default password is "0000"). A confirmation window will be displayed. 3. Select Yes to return back to the factory settings and clear all channels. Select No to cancel. 4. Press the EXIT button to exit. 5.4.4 Software Upgrade 1. Enter the Tools menu, select Software Upgrade and press the OK button.
PART 1 • English 6.0 OPERATION 6.1 Changing Channels There are 4 ways of channel selection: stepping through the channel list, selection by number, from the on-screen channel list and using the Electronic Programme Guide (EPG). Stepping through the channel list To move through the channel list, use the pq buttons on the remote control. Selection by direct channel number input Enter the channel number directly by using the numeric buttons, and press the OK button to select the channel.
Possible cause What to do No signal found Problem Aerial is disconnected Aerial is damaged/misaligned Out of digital signal area Active antenna requires to switch ON antenna power/ external power Check aerial lead Check aerial Check with dealer Switch receiver’s Antenna Power ON/ connect external power No picture or sound on TV Scart/ AV is not selected on your TV TV is not switched on Switch to correct TV input Scrambled channel message Channel is scrambled Select alternative channel No respons
PART 1 • English Tuner: Front End: DVB-T, UHF & VHF Tuner Input frequency range: 174 ~ 230 MHz (VHF) and 470 ~ 862 MHz (UHF) Loop through frequency range: 47 ~ 862 MHz Input signal level: -82 ~ -20 dBm Multimedia: Video playback: Audio playback: Picture view: MPEG-1 and MPEG-2 encoded (mpg) MP3 and WMA formats JPEG and BMP format Memory and System: Flash memory: 1 MByte SDRAM: 8 MBytes Connectors: ANT IN: TO TV: TV SCART (RGB, CVBS) S/PDIF: USB 1.1 port: IEC Female IEC Male coaxial output max.
