Picture sim ilar Satellite Antenna with integrated Single LNB SlimSat SA61 Satellite Antenna with integrated Twin LNB SlimSat SA62 Satellite antenna with integrated Quad LNB SlimSat SA64 User Manual
PART 1 • English 1.0 What is SLIMSAT? 2 2.0 Safety Instructions 2 3.0 How to Install? 3.1 Step 1: Where to Install? 3.2 Step 2: Installation 3.3 Step 3: Connecting the Antenna and the Set top box 3.4 Step 4: Fine Tuning and Fixing the Bracket 3 3 4 6 6 4.0 Troubleshooting Check List for Initial Installation 7 5.0 Loss of Signal / Rain Fade 8 6.0 Installation Using Long Cable 8 7.0 Technical Specification 8 A.1 Box Content 9 English Content A.
PART 1 • English 1.0 WhAT iS SLiMSAT? SLIMSAT is a Horn Array Type Satellite Antenna with integrated LNB. It can receive signals from major Satellites and would replace a 65 cm parabolic dish. Small, discreet and easy to use, it can be installed in a few minutes and used as a portable antenna for all satellite receptions.
PART 1 • English cable between the antenna and the Satellite receiver should not exceed 30m as it will decrease the quality of the signal. The use non- isolated jacks will result in a loss of the signal level. Do not forget to adjust the antenna and the bracket to the cross-polarity (skew angle please refer to chapter 3.4 step 4). Tighten all the screws of the antenna once you have finished the adjustments. This product contains the LNB, it is forbidden to add, change or modify the LNB.
PART 1 • English Think about the way you might pass your cable in a discreet way from the SLIMSAT to your Set top Box. The antenna should not be too distant from your satellite receiver; a cable longer than 30 meters can decrease the quality of the signal. Bad Quality Signal Reception Good Quality Signal Reception 3.2 Step 2: Installation In order to install your new antenna, you need to find the skew, elevation and azimuth angle by referring to the table in the appendix of this manual.
English PART 1 • English Check 30 3. Installation of Fixing Bracket A When installing Fixing Bracket A (B3), please consider the place of installation (clamp type, wall mounting type). Make sure that the direction of the bracket is towards satellite. In order to support the weight of the antenna, nut (N1) should be fixed as tightly as possible. Please purchase the anchor bolt for wall mounting installation separately. Wall Use anchor bold (not included) 4.
PART 1 • English Wall 3.3 Step 3: Connecting the Antenna and the Set top box Once you have installed the antenna in an open loop space and mounted the way you want it to be the next step is to connect it all together. In order to be able to watch your favourite satellite programs, you need to connect your satellite antenna to a receiver by a cable. The cable between the antenna and the Satellite receiver should not exceed 30m as it will decrease the quality of the signal.
Once all connections are made, turn on the TV and the satellite receiver, select the Antenna Pointing Menu on your receiver and check the signal level on your TV. Do not forget to choose “LNB: ON”. Someone will need to stay in front of the TV to tell you when the signal is “good” while you’re outside adjusting the antenna the best way possible.
PART 1 • English Some after market, off-the-shelf add-on components may not be as advertised. They might not work or could cause additional DC drops and signal amplitude attenuation. Remove such components, go back to the basic connections called out in this manual and re-verify. Make sure the satellite cable is connected to the “SAT IN” jack, not the “ANTENNA IN” jack. The “ANTENNA IN“ jack at the back of the receiver is for all off-air antenna input or cable TV input.
PART 1 • English LNB Output Frequency: LNB voltage: Operating Temperature: Gross weight: Net weight: 33.7 dBi at 12.7 GHz 51.7 x 27.7 x 8.2 cm Model SA61: Single LNB integrated Model SA62: Twin LNB integrated Model SA64: Quad LNB integrated 950 – 1,950 / 1,100 – 2,150 MHz Vertical 9 – 14.5 V (typ. 13 V) Horizontal 15.5 – 24 V (typ. 18 V) -30 ~ +60 °C 4.5 kg 2.7 kg English Antenna Gain: Dimensions (W x H x D): LNB: Subject to alterations.
PART 1 • English No Symbol Part name Image Quantity 5 B4 Fix Bracket B 2 6 B5 Spanner 1 7 C1 Compass 1 8 S1 Screw M6x18 SEMS2 3 9 S2 Screw M6x50 SEMS2 1 10 S3 Round Head Square Neck Bolt M6x50 3 11 S4 Round Head Square Neck Bolt M6x75 4 12 N1 Flanged Nut M6 7 31 May 2010 15:16 10
A.
Germany 2
France 3
Italy 4
Spain 5
Switzerland 6
Norway Denmark 7
Austria 8
9
10
