Installation Guide

ManualsBrandsStretta ManualsKitchenOff-White Laminate Countertop Miter Bolt Kit

STRETTA COUNTERTOP

IMPORTANT INFORMATION ABOUT YOUR STRETTA COUNTERTOP

STRETTA

COUNTERTOP INSTALLATION

• CAUTION: The product is heavy and should be lifted by two people to avoid injury or

damage during installation.

• For Indoor Installation Only

• To clean your Stretta countertop, use a mild dish soap and warm water applied with a soft

cloth. Do not utilize abrasive cleaners or cleaning tools. Always test cleaning products in an

inconspicuous area ﬁrst.

• Your Stretta countertop is manufactured with 100% pre-consumer recycled cores and

low-emitting, water-based adhesives.

INSTALLATION KIT CONTAINS:

TOOLS REQUIRED:

from VT Industries

™

from VT Industries

™

from VT Industries

™

SAFETY:

from VT Industries

™

4 Wood Biscuits

Multi-bit Screwdriver

or Drill

Pencil

Measuring

Tape

Masking

Tape

Circular

Saw

Stretta Countertops – Installation Made Easy

With Stretta’s patent-pending installation process,

installing a countertop has never been faster or easier!

Safety

Glasses

Dusk

Mask

Ear

Protection

180 Grit

Sandpaper

1 Bottle

Color-matched Adhesive

1 Specialty Screw Bit

3 Specialty Screws

Summary of content (6 pages)

PAGE 1
STRETTA COUNTERTOP INSTALLATION ™ from VT Industries Stretta Countertops – Installation Made Easy With Stretta’s patent-pending installation process, installing a countertop has never been faster or easier! IMPORTANT INFORMATION ABOUT YOUR STRETTA COUNTERTOP • CAUTION: The product is heavy and should be lifted by two people to avoid injury or damage during installation. • For Indoor Installation Only • To clean your Stretta countertop, use a mild dish soap and warm water applied with a soft cloth.
PAGE 2
STEP 1 - TEST FIT ™ from VT Industries Place Stretta countertop(s) on installed base cabinetry to test fit the tops and to determine if you need to modify the length of the countertop(s). Standard overhang for exposed ends is ½” (Figure 1-1) while those that meet a wall or appliance have no overhang and fit flush. Prior to cutting the countertop to length, apply masking tape to the cut line to ensure a smooth cut. Also, make sure the teeth of the saw enter the top surface of the countertop.
PAGE 3
STEP 3 - SECURE COUNTERTOP Slide the countertops away from the wall slightly to access the pockets on the underside of the countertop. Drive the three specialty screws into the pockets using the specialty screw bit included in the Stretta Installation Kit. Two screw pockets are located on the bottom side of the countertop (Figure 3-1) and one is located on the back side of the countertop.
PAGE 4
INSTALACIÓN DEL TOPE STRETTA ™ from VT Industries Topes Stretta - Facilitando la instalación Con el proceso de instalación con patente pendiente de Stretta, instalar un tope nunca ha sido más rápido ni fácil. INFORMACIÓN IMPORTANTE SOBRE SU TOPE STRETTA • ADVERTENCIA: El producto es pesado y debe ser levantado por dos personas para evitar lesiones o daños durante la instalación. • Solo para la instalación en interiores.
PAGE 5
PASO 1 - HAGA UN AJUSTE DE PRUEBA Ponga los topes Stretta sobre los muebles bajos instalados para hacer ajustes de prueba de los topes y determinar si usted tiene que modificar la longitud de los topes. El saliente estándar para los extremos expuestos es de ½” (Figura 1-1), mientras que aquellos que entren en contacto con una pared o un electrodoméstico no tienen un saliente y se ajustan al ras.
PAGE 6
PASO 3 - ASEGURE EL TOPE ™ from VT Industries Separe ligeramente los topes de la pared para acceder a los huecos de la parte inferior del tope. Introduzca los tres tornillos especiales en los huecos con la broca para tornillos especiales incluida en el kit de instalación de Stretta. Dos de los huecos para tornillos se encuentran en el lado inferior del tope (Figura 3-1) y uno se encuentra en la parte posterior del tope (Figura 3-2).