Installation Guide

ManualsBrandsStretta ManualsKitchenOff-White Laminate Endcap Kit

Table Of Contents

STRETTA ENDCAP

IMPORTANT INFORMATION ABOUT YOUR STRETTA COUNTERTOP

STRETTA

ENDCAP INSTRUCTIONS

• CAUTION: The product is heavy and should be lifted by two people to avoid injury or

damage during installation.

• For Indoor Installation Only

• To clean your Stretta countertop, use a mild dish soap and warm water applied with a soft

cloth. Do not utilize abrasive cleaners or cleaning tools. Always test cleaning products in an

inconspicuous area ﬁrst.

• Your Stretta countertop is manufactured with 100% pre-consumer recycled cores and

low-emitting, water-based adhesives.

ENDCAP KIT CONTAINS: TWO ENDCAPS

TOOLS REQUIRED:

from VT Industries

™

from VT Industries

™

from VT Industries

™

SAFETY:

Measuring

Tape

Utility

Scissors

Fine Wood

File

Masking

Tape

Stretta Countertops – Installation Made Easy

With Stretta’s patent-pending installation process,

installing a countertop has never been faster or easier!

STEP 1 - TEST FIT

from VT Industries

™

Remove endcaps from packaging and test ﬁt them to

the exposed ends of the countertop to make sure they

cover the ends. (Figure 1-1) If you need to ﬁnish the

ends of the backsplash, cut 4” off each endcap with

the utility scissors and set the 4” pieces aside. (Figure

1-2) With a dry cotton cloth, wipe the exposed ends of

the countertop to remove any loose particles or debris.

Endcap Back (Self-adhesive paper backing)

Endcap Front (Laminate)

3M ADHESIVE

(Figure 1-1)

4”

(Figure 1-2)

Safety

Glasses

Cotton

Cloth

Summary of content (4 pages)

PAGE 1
STRETTA ENDCAP INSTRUCTIONS ™ from VT Industries Stretta Countertops – Installation Made Easy With Stretta’s patent-pending installation process, installing a countertop has never been faster or easier! IMPORTANT INFORMATION ABOUT YOUR STRETTA COUNTERTOP • CAUTION: The product is heavy and should be lifted by two people to avoid injury or damage during installation. • For Indoor Installation Only • To clean your Stretta countertop, use a mild dish soap and warm water applied with a soft cloth.
PAGE 2
STEP 2 - APPLY ENDCAPS ™ from VT Industries Remove the paper backing on the endcap to expose the adhesive. Line the endcap up with the end of the countertop so that it is flush with the front edge and top of the countertop surface. (Figure 2-1) With your hand, press the endcap firmly against the end of the countertop to activate the adhesive. (Figure 2-1) CAUTION: Take care to properly position the endcap, as it is difficult to reposition the endcaps after the adhesive has set.
PAGE 3
STRETTA ENDCAP INSTRUCTIONS ™ from VT Industries Cubiertas para cocina Stretta - Instalación fácil ¡Con el proceso de instalación de Stretta (con patente pendiente), instalar una cubierta nunca fue tan rápido ni tan fácil INFORMACIÓN IMPORTANTE SU CUBIERTA STRETTA • PRECAUCIÓN: Este producto es pesado y debe ser levantado por dos personas para evitar lesiones o daños durante la instalación.
PAGE 4
PASO 2 - APLIQUE LOS TOPES ™ from VT Industries Retire el papel del dorso del tope para exponer el adhesivo. Alinee el tope con el extremo de la cubierta de modo que quede parejo con el borde frontal y la parte superior de la superficie de la cubierta. (Figura 2-1) Con la mano, presione firmemente el tope contra el extremo de la cubierta para activar el adhesivo.