OPERATION AND PARTS MANUAL STR46SP RIDE-ON POWER TROWEL Revision #1 (08/01/06) THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES. To find the latest revision of this publication, visit our website at: www.multiquip.
WARNING WARNING SILICOSIS WARNING RESPIRATORY HAZARDS Grinding/cutting/drilling of masonry, concrete, metal and other materials with silica in their composition may give off dust or mists containing crystalline silica. Silica is a basic component of sand, quartz, brick clay, granite and numerous other minerals and rocks. Repeated and/or substantial inhalation of airborne crystalline silica can cause serious or fatal respiratory diseases, including silicosis.
STR46SP — TABLE OF CONTENTS Proposition 65 Warning ............................................. 2 Respiratory/Silicosis Warnings .................................. 3 Table of Contents ...................................................... 4 Parts Ordering Procedures ....................................... 5 Training Checklist ...................................................... 6 Daily Pre-Operation Checklist ................................... 7 Safety Message Alert Symbols .............................
STR46SP — PARTS ORDERING PROCEDURES When ordering parts, please supply the following information: ❒ ❒ ❒ ❒ ❒ ❒ ❒ Dealer account number Dealer name and address Shipping address (if different than billing address) Return fax number Applicable model number Quantity, part number and description of each part Specify preferred method of shipment: ✓ FedEx or UPS Ground Note: Unless otherwise indicated by customer, all ✓ FedEx or UPS Second Day or Third Day orders are treated as “Standard Orders”, and will ship wit
STR46SP — TRAINING CHECKLIST TRAINING CHECKLIST This checklist lists some of the minimum requirements for machine operation. Please feel free to make copies for daily use. Use this checklist when training a new operator or use as a review for more experienced operators. TRAINING CHECKLIST NO. DESCRIPTION 1 Read Operator’s Manual completely. 2 Machine layout, location of components, checking of engine and fluid levels. 3 Fuel system, refueling procedure. 4 Operation of spray and lights.
STR46SP — DAILY PRE-OPERATION CHECKLIST DAILY PRE-OPERATION CHECKLIST DAILY PRE-OPERATION CHECKLIST 1 Engine Oil Level. 2 Gearbox Fluid Level. 3 Radiator Coolant Level. 4 Condition of Blades. 5 Blade Pitch Operation. 6 Safety-Stop Switch Operation. 7 Steering Control Operation. 8 Condition of Belts. COMMENTS: STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV.
STR46SP — SAFETY MESSAGE ALERT SYMBOLS FOR YOUR SAFETY AND THE SAFETY OF OTHERS! Safety precautions should be followed at all times when operating this equipment. Failure to read, understand and comply with the Safety Messages and Operating Instructions could result in injury to yourself and others. This Operation Manual has been developed to provide instructions for the safe and efficient operation of the STR46 Series Ride-On Trowel.
STR46SP — SAFETY MESSAGE ALERT SYMBOLS Accidental Starting Accidental starts can cause severe injury or death. ALWAYS place the ON/OFF switch in the OFF position. Disconnect and ground spark plug lead and disconnect negative battery cable from battery before servicing. Respiratory Hazard ALWAYS wear approved respiratory protection. Sight and Hearing hazard ALWAYS wear approved eye and hearing protection. Over Speed Conditions NEVER tamper with the factory settings of the engine governor or settings.
STR46SP — RULES FOR SAFE OPERATION RULES FOR SAFE OPERATION WARNING Failure to follow instructions in this manual may lead to serious injury or even death! This equipment is to be operated by trained and qualified personnel only! This equipment is for industrial use only. The following safety guidelines should always be used when operating the STR46SP Ride-On Trowel. SAFETY ■ DO NOT operate or service this equipment before you read, understand, and comply with all safety messages in this manual.
STR46SP — RULES FOR SAFE OPERATION ■ NEVER run engine without air filter. Severe engine damage may occur. Service air filter frequently to prevent carburetor malfunction. ■ NEVER place your feet or hands inside the guard rings while starting or operating this equipment. ■ AVOID wearing jewelry or loose fitting clothing that may snag on the controls or moving parts as this can cause a serious injury. ■ ALWAYS keep clear of rotating or moving parts while operating the trowel.
STR46SP — RULES FOR SAFE OPERATION Transporting ■ ALWAYS shutdown engine before transporting. ■ Tighten fuel tank cap securely and close fuel petcock to prevent fuel from spilling. ■ Use chock-blocks at each wheel when parked to prevent trailer from rolling. ■ Use the trailer's swivel jack to adjust the trailer height to a level position while parked. ■ Drain fuel when transporting trowel for long distances or over bad roads. ■ Avoid sudden stops and starts.
STR46SP — RULES FOR SAFE OPERATION Maintenance Safety Emergencies ■ ALWAYS shut down the engine and disconnect battery before performing service or maintenance functions. Contact with moving parts can cause serious injury. ■ ALWAYS know the location of the nearest fire extinguisher. ■ Securely support any trowel components that must be raised. ■ NEVER lubricate components or attempt service on a running trowel. ■ ALWAYS allow the trowel a proper amount of time to cool before servicing.
STR46SP — OPERATION AND SAFETY DECALS Machine Safety Decals The STR46SP Ride-On Power Trowel is equipped with a number of operation and safety decals. These decals are provided for operator safety and maintenance information. Should any of these decals become unreadable, replacements can be obtained from your dealer. WARNING To avoid injury, you MUST read and understand operator’s manual before using this machine. This machine to be operated by qualified personnel only. Ask for training as needed.
STR46SP — SPECIFICATIONS (TROWEL) C B A Figure 1. STR46SP Dimensions Table 1. STR46 Specifications A–Length – in. (cm) 95.0 (241.3) B–Width – in. (cm) 48.0 (122) m C–Height – in. (c ) 46.0 (116.8) Weight – lbs. (kgs.) Operating 705 (320.5) Weight – lbs. (kgs.) Shipping 1130 (513.6) Rotor – RPM (Dry Concrete) 150 Path Width – in. (cm) 91 (231) Hand/Arm Vibration1 2.79 ft/s2 (m/s2) Whole Body Vibration TBD ft/s2 (m/s2) Sound Pressure (A-Weighted)2 90 dB(A) NOTE: 1.
STR46SP — SPECIFICATIONS (ENGINE) Table 2. STR46 Engine Specifications Model STR46 Kohler 27 HP Engine Type 4 Stroke, Overhead Valve V-Twin, gasoline engine. Piston Displacement 44.0 cu.in. (725 cc) Max. Output 27 bhp/3200 rpm (20.1 KW) Max. Torque 42.7 lbf-ft at 2200 rpm Cooling System Forced Air Engine Oil Capacity 1.75 qt. (1.6 liters) 2.1 qt. (1.9 liters w/oil filter replacement) Fuel Tank 5 gal.(19.23 liters) Gear Box Oil Capacity 69 oz. (2.
STR46SP — GENERAL INFORMATION STR46 SERIES Ride-On Power Trowel Familiarization Gearboxes The STR46 SERIES Ride-On Power Trowel is designed for the floating and finishing of concrete slabs. The STR46 Series Ride-On Power Trowel uses two separate gearbox assemblies that are enclosed in rugged cast aluminum gear cases. Take a walk around your trowel.
STR46SP — CONTROLS AND INDICATORS 1. Seat – Engine will neither start nor run unless operator is seated. 8. Choke Control Lever – In cold weather pull this lever to start engine. After engine warms push knob all the way in. 2. Steering Control Levers – Directs the unit forward, reverse, left, or right. 9. Fuel Gauge/Filler Cap – Indicates the amount of fuel in the fuel tank. Remove this cap to add fuel. 3.
STR46SP — CONTROLS AND INDICATORS 17. Safety Stop Switch – Shuts down engine when seat is empty. 26. Spiders (Left/Right) – Consists of trowel arms, blades, wear plate, and thrust collar. 18. Light Assembly – Optional 12 volt halogen lights are available, two forward and one aft. 27. Document Box – Contains all product documentation. 19. Lift Loops – Located on both sides of the main frame. Used to lift the trowel. 29. Belt Guard – Encloses drive belt used in conjunction with clutch. 20.
STR46SP — BASIC ENGINE 2 3 8 1 9 7 10 6 11 5 4 12 Kohler 27 HP Engine Figure 4. Engine Controls and Components INITIAL SERVICING The engine must be checked for proper lubrication and the fuel tank filled with fuel prior to operation. Refer to the manufacturer's engine manual for instructions & details of operation and servicing. The engine shown in Figure 4 is a Kohler engine. 1. 5. Oil Cooler – Helps keep engine oil cooler for longer engine life. 6.
STR46SP — NEW MACHINE SETUP INSTRUCTIONS Trowel Pre-Set Up Instructions Seat Assembly The purpose of this section is to assist the user in setting up a NEW trowel. If your trowel is already assembled, (seat, handles, knobs and battery), this section can be skipped. The seat is not installed on the trowel for shipping purposes. To attach the seat perform the following: NOTE The new trowel cannot be put into service until the pre-setup installation instructions are completed.
STR46SP — INITIAL START-UP The following section is intended as a basic guide to the ride-on trowel operation, and is not to be considered a complete guide to concrete finishing. It is strongly suggested that all operators (experienced and novice) read “Slabs on Grade ” published by the American Concrete Institute, Detroit Michigan. Table 3. Recommended Viscosity Grades DO NOT use your ride-on power trowel until this section is thoroughly understood.
STR46SP — OPERATION FUEL EN GIN EF UE LO NL Y E F 5. When starting a cold engine, pull the choke knob, if so equipped, (Figure 9) out to the closed position. In warm weather or when the engine is warm, the unit can be started with choke halfway or completely open. CHOKE KNOB Figure 7. Fuel Gauge CLOSED Important Information Before You Start 1. This ride-on trowel is equipped with a safety "safety stop switch". This switch is located beneath the seat assembly.
STR46SP — OPERATION Steering 5. Two control levers located in front of the operator’s seat provide directional control for the STR46 SERIES Ride-On Power Trowel. Table 4 (Page 26) illustrates the various directional positions of the joysticks and their effect on the ride-on trowel. Try adjusting the pitch of the blades. This can be done with the ride-on trowel stopped or while the trowel is moving, whatever feels comfortable.
STR46SP — MAINTENANCE Maintenance When performing any maintenance on the trowel or engine, follow all safety messages and rules for safe operation stated at the beginning of this manual. WARNING Accidental starts can cause severe injury or death. ALWAYS place the ON/OFF switch in the OFF position. Disconnect and ground spark plug leads and disconnect negative battery cable from battery before servicing. Figure 12. Engine Service Areas MAINTENANCE SCHEDULE 1. Oil Level Dipstick 1. 2.
STR46SP — MAINTENANCE Air Cleaner (Daily) The Kohler 27 hp engine is equipped with a replaceable, highdensity paper air cleaner element. Most are also equipped with an oiled-foam precleaner which surrounds the paper element. Check the air cleaner daily or before starting the engine. Check for and correct heavy buildup of dirt and debris along with loose or damaged components. 1. 2. 3. 4.
STR46SP — MAINTENANCE Air Cleaner Components - See Figure 13. 1. Air Cleaner Cover 2. Latch Spring 3. Lever Latch 4. Latch Lever Pin 5. Wing Nut 6. Inner Air Cleaner Cover 7. Precleaner Element 8. Air Cleaner Element 9. seal Air Cleaner - Components to Check Whenever the air cleaner cover is removed, or the paper element or precleaner is serviced, check the following: ■ Air Cleaner Element Cover and Seal - Make sure the element cover is not bent or damaged.
STR46SP — MAINTENANCE Changing Engine Oil And Filter 1. Change the engine oil after the first 5 hours of use, then change every 6 months or 100 hours. 2. Remove the oil filler cap (Figure 12, Item 5), and fill engine crankcase with recommended type oil as listed in Table 3. Fill to the upper limit of dipstick. 3. Crankcase oil capacity with oil filter replacement is 2.02 qts. (1.90 liters). Oil Filter (100 Hours) 1. Replace the engine oil filter (Figure 14) every oil change or 100 hours.
STR46SP — MAINTENANCE Checking The Drive Belt 5 The drive belt needs to be replaced as soon as it starts to show signs of wear. Indications of excessive belt wear are fraying, squealing when in use, belts that emit smoke or a burning rubber smell when in use. Under normal operating conditions, a drive belt may last approximately 150 hours. If your trowel is not reaching this kind of life span for drive belt wear, check the drive belt for proper pulley alignment and spacing.
STR46SP — MAINTENANCE 3. Insert the 3/4" X 1" X 3-1/4" block between the moveable face and the fixed face of the lower drive pulley. See Figure 19. This block will help keep the lower drive pulley faces open while installing the new drive belt. In the event of a drive belt failure, the spare (replacement) drive belt can be used for quick replacement at the job site to continue trowel operation. 1. If necessary, refer to Removing Drive Belt Instructions.
STR46SP — MAINTENANCE 5 4 6 2 1 3 1 2 3 4 5 6 CV Joint Bolt (Remove 3 places) New Spare Drive Belt Bolt, Spare Drive Belt Carrier Spare Drive Belt Holder Left Side Gearbox Figure 21. Spare Drive Belt Replacement Spare Drive Belt Replacement It will be necessary to disconnect the CV-Joint from the left-side gearbox coupler. This means the removal of the three screws that secure the CVJoint to the gearbox. 3.
STR46SP — MAINTENANCE Drive System Theory of Operation The STR46SP Ride-On Power Trowel is equipped with a "Torque Converter" which supplies torque to both the left and right gearboxes. The function of the torque converter is to automatically deliver the correct amount of torque required by the trowel under all load conditions. This enables the trowel to deliver the necessary torque for float pan applications and the high rotor speeds required for burnishing concrete.
STR46SP — MAINTENANCE How It Works (Figure 26) Condition A: Blade Pitch z Engine Idling z Drive Pulley: Small z Driven Pulley: Large z Belt: Loose and Stationary Condition B: z Engine Accelerating z Drive Pulley: Small But Increasing Sometimes it may be necessary to match blade pitch between the two sets of blades. There are some signs that this may be necessary. For example, the differences in pitch could cause a noticeable difference in finish quality between the two sets of blades.
STR46SP — MAINTENANCE Trowel Arm adjustment Procedure NOTE Figure 30 below illustrates the "correct alignment " for a spider plate (as shipped from the factory). The following procedure should be followed to adjust trowel arms when it becomes apparent that the trowel is finishing poorly or in need of routine maintenance. A level, clean area to test the trowel prior to and after adjustement is essential.
STR46SP — MAINTENANCE Trowel Arm Removal Trowel Blade Removal 1. Each trowel arm is held in place at the spider plate by a hex head bolt (with zerk grease fitting). Remove the hex head bolt/zerk grease fitting from the spider plate. (Figure 32) 1. Remove the trowel blades from the trowel arm by removing the three hex head bolts (Figure 34) from the trowel arm. Set blades aside. 2. Remove the trowel arm from the spider plate. Figure 34.
STR46SP — MAINTENANCE Checking Trowel Arm Straightness Trowel arms can be damaged by rough handling, (such as dropping the trowel on the pad), or by striking exposed plumbing, forms, or rebar while in operation. A bent trowel arm will not allow the trowel to operate in a smooth fluid rotation. If bent trowel arms are suspect, check for flatness as follows, refer to Figures 35 and 36: 3.
STR46SP — MAINTENANCE 4. Use an allen wrench to tighten the locking bolts securing the trowel arm in place. 5. Adjust the bolt "distance" shown in Figure 37 to match one of the arms. The other arms will be adjusted to match this distance. 6. Loosen the locking nut on the trowel arm lever, then turn the trowel arm adjusting bolt until it barely touches (.010") the fixture adjusting bolt. 7. Once the correct adjustment is made, tighten the lock nut on the trowel arm to lock in place. Figure 38.
STR46SP — MAINTENANCE Installing Pans Onto Finisher Blades These round discs sometimes referred to as "pans" attach to the spiders arms and allow early floating on wet concrete and easy movement from wet to dry areas. They are also very effective in embedding large aggregates and surface hardeners. 1. Lift trowel just enough to slide pan under blades. Lower finisher onto pan with blades (Item #1) adjacent to Z-Clips (Item #4). 2. Rotate blades into position under Z-Clips.
STR46SP — TROUBLESHOOTING (ENGINE) TABLE 5. ENGINE TROUBLESHOOTING SYMPTOM Engine Cranks But Will Not Start Engine Starts But Will Not Continue Running POSSIBLE PROBLEM SOLUTION Fuel tank is empty. Fill fuel tank. Shut-off valve is closed. Open fuel shut-off valve. Fuel line has suction leak or is restricted. Fuel filter, or fuel tank cap vent is obstructed. Check fuel line condition and fuel line clamps. Ensure that fuel line is not kinked.
STR46SP — TROUBLESHOOTING (ENGINE) TABLE 5 CONT.. ENGINE TROUBLESHOOTING SYMPTOM Engine Lacks Power POSSIBLE PROBLEM SOLUTION Air filter is obstructed. Replace air filter. Altitude causes 3% loss of horsepower per 1000 feet of altitude. If available, install high altitude jets in carburetor. Choke is par tially closed. Open choke. Faulty spark plugs or spark plug leads. Spark plug lead disconnected. Replace spark plugs or spark plug leads if faulty. Reattach spark plug lead if disconnected.
STR46SP — TROUBLESHOOTING (TROWEL) TABLE 6. TROUBLESHOOTING SYMPTOM Engine running rough or not at all. POSSIBLE PROBLEM SOLUTION Safety Stop Switch malfunction? Make sure that the Safety Stop Switch is functioning when the operator is seated; replace switch if necessary. Fuel? Look at the fuel system. Make sure there is fuel being supplied to the engine. Check to ensure that the fuel filter is not clogged. Ignition? Check to ensure that the ignition switch has power and is functioning correctly.
STR46SP — TROUBLESHOOTING (TROWEL) TABLE 6. TROUBLESHOOTING (CONTINUED) SYMPTOM POSSIBLE PROBLEM SOLUTION Wiring? Check all electrical connections, including the master on/off switch and check to see if wiring is in good condition with no shorts. Replace as necessary. Lights? Check to see if light bulbs are still good. Replace if broken. Retardant? Check the tank to make sure retardant is present. Fill tank as necessary.
STR46SP — NOTES STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV.
STR46SP — EXPLANATION OF CODE IN REMARKS COLUMN The following section explains the different symbols and remarks used in the Parts section of this manual. Use the help numbers found on the back page of the manual if there are any questions. The contents and part numbers listed in the parts section are subject to change without notice. Multiquip does not guarantee the availibility of the parts listed. PART NO. PART NAME QTY. 12345 BOLT ....................... 1.... WASHER, 1/4 IN. ...........
STR46SP — SUGGESTED SPARE PARTS STR46SP KOHLER ENGINES 1 Unit P/N 10 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 1 1 1 10031 .................... WASHER 1/4 IN. 12548 .................... SPRAY PUMP 392292 .................. SPRAY NOZZEL 2108 ...................... CAP, SPRAY TANK 2673 ...................... CIRCUIT BREAKER 30A, 12V 4682 ...................... TOGGLE SWITCH 8381 ...................... BOOT, TOGGLE SWITCH 12005 .................... ENGINE-OFF SAFETY SWITCH 12018 ....................
STR46SP — NAMEPLATE AND DECALS NAMEPLATE AND DECALS PAGE 46 — STR 31V STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV.
STR46SP — NAMEPLATE AND DECALS NAMEPLATE AND DECALS NO. 1 1A * 1B * 1C * 1D * 1E * 1F * 1G * 1H * 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 PART NO. 11246 13118 11111 2300 2332 2634 1499 36099 2814 TBD 35137 11092 35168 20525 21455 36090 PART NAME QTY. REMARKS DECAL SET, INTERNATIONAL STDS ................... 1 .............
STR46SP — PIVOT ASSY. (RIGHT/LEFT) PIVOT ASSY. (RIGHT/LEFT) PAGE 48 — STR 31V STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV.
STR46SP — PIVOT ASSY. (RIGHT/LEFT) PIVOT ASSY. (RIGHT/LEFT) NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PART NO. 1023 0166 A 2304 2146 10138 12412 4196 5054 A 8136 12413 2312 2145 1394 11248 PART NAME SCREW, HHC 3/8 - 16 X 1-1/4 WASHER, LOCK, 3/8 MED.
STR46SP — STEERING HANDLES ASSY. (RIGHT/LEFT) STEERING HANDLES ASSY. (RIGHT/LEFT) PAGE 50 — STR 31V STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV.
STR46SP — STEERING HANDLES ASSY. (RIGHT/LEFT) STEERING HANDLES ASSY. (RIGHT/LEFT) NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 PART NO. 0189 11142 11177-1 2197 5277 12425-1 11141 11143 11173 11146 11144 10133 11145 0131 A 11205 10024 0447 12426 1023 10136 2219 10176 12193 2267 EM963105 8151 12374-1 12375-1 0735 0735 A 11149 11138 PART NAME QTY.
STR46SP — STEERING ASSIST CONTROL ASSY. (RIGHT/LEFT) STEERING ASSIST CONTROL ASSY. (RIGHT/LEFT) PAGE 52 — STR 31V STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV.
STR46SP — STEERING ASSIST CONTROL ASSY. (RIGHT/LEFT) STEERING ASSIST CONTROL ASSY. (RIGHT/LEFT) NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 PART NO. 11146 11142 EM963105 10176 12200 0447 11143 5054 A 8136 11127-1 0131 A 11150 11139 PART NAME QTY. REMARKS NUT, HEX JAM 1/2 -20 PLTD 6 ROD END, 1/2 - 20 MALE RH 6 SCREW, HHC 1/2 -13 X 2 .................................... 10 ..................
STR46SP — GEARBOX ASSY. (RIGHT) GEARBOX ASSY (RIGHT) PAGE 54 — STR 31V STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV.
STR46SP — GEARBOX ASSY. (RIGHT) GEARBOX ASSY (RIGHT) NO. PART NO.
STR46SP — GEARBOX ASSY. (LEFT) GEARBOX ASSY (LEFT) PAGE 56 — STR 31V STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV.
STR46SP — GEARBOX ASSY. (LEFT) GEARBOX ASSY (LEFT) NO. PART NO.
STR46SP — SINGLE PITCH HANDLE ASSY. (RIGHT/LEFT) SINGLE PITCH HANDLE ASSY. (RIGHT/LEFT) PAGE 58 — STR 31V STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV.
STR46SP — SINGLE PITCH HANDLE ASSY. (RIGHT/LEFT) SINGLE PITCH HANDLE ASSY. (RIGHT/LEFT) NO 1#%+ 2#%+ 3#%+ 4#%+ 5#%+ 6#% 7#% 8#% 9#% 10#% 11#% 12#% 13# 14# 15# 16# 17# 18# 19# 20# 21# 22# 23# 24# 25# 26# 27# 28# 29# 30 PART NO 4403 3231 2575 1733 1616 2737 2621 1162A 4014 2332 2300 0185 1617 2170 1604 1111 2367 2169 10646 10382 10721 10723 12460 1116 10548-1 0202 0300B 5283 10512 11109-1 PART NAME QTY. REMARKS CRANK KNOB 2 SPACER 2 CRANK LEVER 2 HARDENED WASHER 2 SHOULDER BOLT 2 KNOB KIT ..................
STR46SP — DRIVE ASSY. DRIVE ASSY. PAGE 60 — STR 31V STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV.
STR46SP — DRIVE ASSY. DRIVE ASSY. NO. 1 2 * 3 * 4 * 5 * 6 * 7 * 8 * 9 * 10 * 11 * 12 * 13 * 14 * 15 * 16 * 17 * 18 * 19 * 20 * 21 * 22 * 23 * 24 * 25 % * 26 * 27 * 28 * 29 * PART NO. 21494 20186 300518C 0126 2090 1146 2037 2029 10337 20044 10136 10133 21475 20043 20116 21491 12590 20056 2052 11108 1662 0243 0161 C 2074 2259 2186 10748 20187 10909 PART NAME QTY. REMARKS DRIVE ASSEMBLY, W/COMET ....................................... 1 ............
STR46SP — ENGINE/MUFFLER/BELT ASSY. ENGINE/MUFFLER/BELT ASSY. PAGE 62 — STR 31V STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV.
STR46SP — ENGINE/MUFFLER/BELT ASSY. ENGINE/MUFFLER/BELT ASSY. NO. 1 2 3 4 5 7 8 9 10 11 12 13 15 16 17 18 29 20 21 22 PART NO. M841080S 2404149S 2507204S M650012S 2431404S 2406836S 2412690S M839020S 21421 1207 0300 B 0161 C 20444 20138 20846 21528 4703 21316 5283 21489 PART NAME NUT, FLANGE MUFFLER GASKET, EXHAUST MANIFOLD STUD, EXHAUST SCREW, HEX FLANGE INNER HEAT SHIED, MUFFLER MUFFLER, O.F.
STR46SP — AIR CLEANER/OIL FILTER/OILCOOLER ASSY. AIR CLEANER/OIL FILTER/COOLER ASSY. PAGE 64 — STR 31V STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV.
STR46SP — AIR CLEANER/OIL FILTER/OILCOOLER ASSY. AIR CLEANER/OIL FILTER/COOLER ASSY. NO. 1 2 * 3 * 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 24A# 24B# 25 26 27 28 29 30% 31% 32% PART NO. 5475501S 2534104S 2415320S 2409667S 1210001S 2409601S 230046S 2408305S 2408303S 2408653S 2412688S 2409437S 2404106S 2655 8239 2513212 5205002S 19317 TBD 370628 60045 1947 12237 5475521S 2813601S 2415321S 2540305S 12236 24126130S 2404106S 2416454S 2404153S 2415327S M651040S PART NAME QTY.
STR46SP — V-BELT COVER/OUTER MUFFLER SHIELD ASSY. V-BELT COVER/OUTER MUFFLER SHIELD ASSY. PAGE 66 — STR 31V STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV.
STR46SP — V-BELT COVER/OUTER MUFFLER SHIELD ASSY. V-BELT COVER/OUTER MUFFLER SHIELD ASSY. NO. 1 2 3 4 5 PART NO. 21462 11819 21312 21309 11534 PART NAME SHIELD, MUFFLER OUTER SCREW, HHC FLANGED 1/4-20X3/4" GUARD, BELT REAR GUARD, BELT NUT, U-TYPE 1/4-20 QTY. 1 7 1 1 7 REMARKS STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV.
STR46SP — SPIDER ASSY. (RIGHT) SPIDER ASSY. (RIGHT) PAGE 68 — STR 31V STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV.
STR46SP — SPIDER ASSY. (RIGHT) SPIDER ASSY. (RIGHT) NO. 1% 2% 3% 4% 5 6 * 7 * 9 * 10 * 11 * 12 * 13 * 15 * 16 * 17 * 18 * 19 * 20 * 21 * 22 * 23 # * 24 25 * 26 PART NO. 11419 11431-1 2621 12779 12101 12097 1456 11039 11594 11904 9006 2829 1207 0161 C 1162 A 1322 1875 0164 B 1876 0166 A 11602 12072-1 12785 27+% 12316 28% 20938 PART NAME QTY. REMARKS PLATE, WEAR THRUST COLLAR 1 THRUST COLLAR W/ BUSHING................................... 1 .....
STR46SP — SPIDER ASSY. (LEFT) SPIDER ASSY, (LEFT) PAGE 70 — STR 31V STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV.
STR46SP — SPIDER ASSY. (LEFT) SPIDER ASSY. (LEFT) NO. 1% 2% 3% 4% 5 6 * 7 * 9 * 10 * 11 * 12 * 13 * 15 * 16 * 17 * 18 * 19 * 20 * 21 * 22 * 23 # * 24 25 * 26 PART NO. 11419 11431-1 2621 12779 12101 12097 1456 11039 11595 11903 9006 21495 1207 0161 C 1162 A 1322 1875 0164 B 1876 0166 A 11602 21310-1 12785 27+% 12316 28% 20938 PART NAME QTY. REMARKS PLATE, WEAR THRUST COLLAR 1 THRUST COLLAR W/ BUSHING................................ 1.............
STR46SP — YOKE ASSY. YOKE ASSY. PAGE 72 — STR 31V STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV.
STR46SP — YOKE ASSY. YOKE ASSY. NO. 1 2 3 4 5 6 PART NO. 12100-1 0683 10136 9028 1116 12460 PART NAME YOKE PIN, COTTER 3/32 X 3/4 WASHER, FLAT 3/8 SAE PIN, YOKE NUT, BRASS JAM 5/16 -18 CABLE ASSEMBLY 26.38 HT-V PITCH QTY. 2 4 6 2 4 2 REMARKS STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV.
STR46SP — THROTTLE CABLE/FOOT PEDALS ASSY. THROTTLE CABLE/FOOT PEDALS ASSY. PAGE 74 — STR 31V STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV.
STR46SP — THROTTLE CABLE/FOOT PEDALS ASSY. THROTTLE CABLE/FOOT PEDALS ASSY. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 PART NO.
STR46SP — CONTROL PANEL ASSY. CONTROL PANEL ASSY. PAGE 76 — STR 31V STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV.
STR46SP — CONTROL PANEL ASSY. CONTROL PANEL ASSY. NO. 1 2 3 4 4A 5 6 7 8 9 10 11 12 13 14 15 16 17 18 PART NO.
STR46SP — FUEL ASSY. FUEL ASSY. PAGE 78 — STR 31V STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV.
STR46SP — FUEL ASSY. FUEL ASSY. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 PART NO. 12404 11418 4514 0948 19633 20795 19473 60079 0181 B 2405002S 2555901S 2405010S 2429 PART NAME QTY. REMARKS TANK, FUEL FIVE GALLON 1 FUEL CAP/GAUGE (10.5) 1 SCREW, HHC 1/4 - 20 X 5/8 6 WASHER, FLAT, 1/4 SAE 6 BUSHING, RUBBER FUEL 1 VALVE, SCREENED DAPCO 12570 1 CLAMP, WORM HOSE, #4 (1/4 - 5/8) 3 HOSE, FUEL 5/16 ID .............................................. 3 .................. SOLD IN 1 FT.
STR46SP — BATTERY ASSY. BATTERY ASSY. PAGE 80 — STR 31V STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV.
STR46SP — BATTERY ASSY. BATTERY ASSY. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PART NO. 2509 10031 11105 2449 0131 A 0181 B 0949 12022 12675 1597 0655 20146 2866 13339 5283 PART NAME QTY. REMARKS WING NUT, PLATED 2 WASHER, EXT SHKP 1/4 2 BRACKET BATTERY HOLD DOWN 1 BOX, BATTERY GR UI 1 SCREW, HHC 1/4 - 20 X 3/4 2 BATTERY, ................................................ 1 .......
STR46SP — SEAT FRAME ASSY. SEAT FRAME ASSY. PAGE 82 — STR 31V STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV.
STR46SP — SEAT FRAME ASSY. SEAT FRAME ASSY. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 PART NO. 21861 11472-1 0300 B 5283 10896-1 11644 10237 8156 4001 11593 10133 0183 8081 10307 12014 10176 10019 12018 12017 12005 12020 10306 PART NAME SEAT, MICHIGAN-ADJUSTABLE W/O ARMS SEAT PLATE WASHER, FLAT, SAE 5/16 NUT, NYLOC 5/16 - 18 FRAME, SEAT SCREW, HHC, WASHER 10 - 32 X 5/8 WASHER, EXT. SHKP, #10 SCREW, HHC 3/8 - 16 X 2 - 1/2 WASHER, FLAT 3/8 PLTD STD.
Effective: July 15, 2003 TERMS AND CONDITIONS OF SALE — PARTS Terms and Conditions of Sale STOW Construction Equipment PAYMENT TERMS Terms of payment for unit sales are 2% 15 days net 30 days from date of invoice unless otherwise specifically stated on our invoice. Parts invoices have terms of net 10 days. Minimum parts billing is $15.00 net. Applicable discounts will be computed on merchandise value only. Late charges will be assessed at prevailing rates.
STR46SP — NOTES STR46SP • RIDE-ON POWER TROWEL — OPERATION MANUAL — REV.
OPERATION AND PARTS MANUAL HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING STOW MAIN OFFICE Post Office Box 6254 Carson, Ca 90749 Email: stow@multiquip.com Internet: www.stowmfg.com PARTS DEPARTMENT 800-427-1244 310-537-3700 SERVICE DEPARTMENT 800-478-1244 310-537-3700 TECHNICAL ASSISTANCE 800-478-1244 WARRANTY DEPARTMENT 800-421-1244, EXT. 279 310-537-3700, EXT.
