PARTS AND OPERATION MANUAL STOW A D I V I S I O N O F M U LT I Q U I P I N C. PLASTER / MORTAR MIXERS © COPYRIGHT 2002 MULTIQUIP INC. MS-40H (Steel-Drum Hydraulic) Revision #1 (05/17/02) A D I V I S I O N O F M U LT I Q U I P I N C. STOW CONSTRUCTION EQUIPMENT A DIVISION OF MULTIQUIP INC. POST OFFICE BOX 6254 CARSON, CALIFORNIA 90749 310-537-3700 • 888-252-STOW [888-252-7869] FAX: 310-537-1986 • FAX: 800-556-1986 E-MAIL: stow@multiquip.com • WWW: stowmfg.
PAGE 2 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV.
HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING PARTS DEPARTMENT 800-427-1244 or 310-537-3700 FAX: 800-672-7877 or 310-637-3284 SERVICE DEPARTMENT/TECHNICAL ASSISTANCE 800-478-1244 or 310-537-3700 FAX: 310- 537-4259 WARRANTY DEPARTMENT 888-661-4279, or 310-661-4279 FAX: 310- 537-1173 MAIN 800-421-1244 or 310-537-3700 FAX: 310-537-3927 STOW MS-40H HYDRAULIC MIXER — PARTS & OPERATION MANUAL — REV.
TABLE OF CONTENTS Here's How To Get Help ........................................... 3 Table Of Contents .................................................... 4 Parts Ordering Procedures ...................................... 5 Operation and Safety Decals ................................... 6 Rules For Safe Operation ..................................... 7-8 Specifications ........................................................... 9 General Information ...............................................
PARTS ORDERING PROCEDURES n n n n n n n Dealer account number Dealer name and address Shipping address (if different than billing address) Return fax number Applicable model number Quantity, part number and description of each part Specify preferred method of shipment: • • • • UPS Ground UPS Second Day or Third Day* UPS Next Day* Federal Express Priority One (please provide us with your Federal Express account number)* • • Airborne Express* Truck or parcel post *Normally shipped the same day the order
MS-40H HYDRAULIC MIXER — OPERATION AND SAFETY DECALS Machine Safety Decals This STOW mixer is equipped with a number of safety decals. These decals are provided for operator safety and maintenance information. The illustration below shows these decals as they appear on the mixer. Should any of these decals become unreadable, replacements can be obtained from your dealer. SAFETY INSTRUCTIONS A D I V I S I O N O F M U LT I Q U I P I N C. 1. Read owners manuals before operating. 2.
MS-40H HYDRAULIC MIXER — RULES FOR SAFE OPERATION CAUTION: Failure to follow instructions in this manual may lead to serious injury or even death! This equipment is to be operated by trained and qualified personnel only! This equipment is for industrial use only. The following safety guidelines should always be used when operating the MS-40H mixer: GENERAL SAFETY ■ DO NOT operate or service this equipment before reading this entire manual.
MS-40H HYDRAULIC MIXER — RULES FOR SAFE OPERATION CAUTION: ■ Caution must be exercised while servicing this equipment. Rotating and moving parts can cause injury if contacted. Failure to follow instructions in this manual may lead to serious injury or even death! This equipment is to be operated by trained and qualified personnel only! This equipment is for industrial use only. ■ When towing, an adequate safety chain must be fastened to the frame, refer to page 13.
MS-40H HYDRAULIC MIXER — SPECIFICATIONS Table 1. MS-40H Hydraulic Mixer Capacity - cu. ft (liters) 12 (340) Bag capacity - bags 3.5 to 4 Weight - lbs (kg.) 1,010 (458) Length w/Tow Bar x W x H - in. (cm.) 82 x 51 x 60 (208 x 130 x 152) Height W/Dump Handle - in (cm.) 75 (191) Discharge Height - in (cm.
MS-40H HYDRAULIC MIXER — GENERAL INFORMATION GENERAL GASOLINE ENGINE CARE The STOW MS-40H plaster and mortar hydraulic mixer is shipped completely assembled and has been factory tested. For care and operation of the gasoline engine, refer to the engine manufacturer’s operating instructions furnished with the engine. We recommend draining and refilling the engine crankcase at least every thirty hours of operation. Check the engine oil level daily. The drum batch capacity of these mixers is between 3.
MS-40H HYDRAULIC MIXER — CONTROLS Figure 1. Mixer Safety Grill — Provided for operator safety. This safety grill is designed to keep hands and solid objects out of the mixing drum when in use. This grill should be closed at all times when mixer is in use. DO NOT remove the grill or grill opening bar. Keep the grill clean by washing it down daily. Mixing Drum — Made of steel. Mixing materials such as concrete, mortar, plaster are to be placed into this drum for mixing. Always clean the drum after each use.
MS-40H HYDRAULIC MIXER — ELECTRIC MOTOR ELECTRIC MOTOR For lubrication care and operation of the electric motor, refer to your electric motor instruction booklet furnished with the motor. Protect the electric motor from dust as much as possible and keep ventilating openings clean. CAUTION: ■ DO NOT spray water at any time on the electric motor. ■ DO NOT operate electric motor in a explosive environment.
MS-40H HYDRAULIC MIXER — TOWING STEP 3 NOTE Before towing, check with local and state laws for proper compliance. The tow bar and chain must be properly attached to the mixer and towing vehicle prior to towing. Refer to the following installation instruction: VEHICLE CONNECTOR LINK DRAW BAR REMOVE EXCESS CHAIN (SLACK) BOTTOM CONNECTOR LINK Step 1. Insert the Draw Bar into the main frame. Secure, utilizing the 3/4" bolt (grade 5) and nylock nut. Tighten to 100 foot pounds.
MS-40H HYDRAULIC MIXER — PADDLE BLADE ADJUSTMENT Figure 3 illustrates the paddle blade adjustment when using a steel drum. If material builds up on the drum, use a rubber mallet to dislodge the material without adverse effect to the drum. Figure 3. Paddle Blade Adjustment, Steel Drum PAGE 14 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV.
MS-40H HYDRAULIC MIXER — NOTE PAGE STOW MS-40H HYDRAULIC MIXER — PARTS & OPERATION MANUAL — REV.
MS-40H HYDRAULIC MIXER — INITIAL START-UP This section is intended to assist the operator with the initial start-up of the STOW MS-40H hydraulic mixer. It is extremely important that this section be read carefully before attempting to use the mixer in the field. DO NOT use your mixer until this section is thoroughly understood. STARTING THE ENGINE (gasoline only) The following steps outline the procedure for starting the engine.
MS-40H HYDRAULIC MIXER — INITIAL START-UP 4. Turn the engine switch (Figure 8) to the ON position. MIXING 1. The paddle shaft inside the drum should be rotating at this time. 2. Lift the mixing bag compound onto the steel grate over the bag cutter and let the contents fall into the drum. 3. Add water, and mix compound to desired consistency, then dump. NOTE Be sure to stand clear of the dump handle when the mixer is operational.
MS-40H HYDRAULIC MIXER — MAINTENANCE WHEEL BEARINGS PADDLE SHAFT BEARINGS After every 3 months of operation, remove the hub dust cap and inspect the wheel bearings. Once a year, or when required, disassemble the wheel hubs remove the old grease and repack the bearings forcing grease between rollers, cone and cage with a good grade of high speed wheel bearing grease (never use grease heavier than 265 A.S.T.M. penetration (“No. 2.
MS-40H HYDRAULIC MIXER — TROUBLESHOOTING (ENGINE) Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a breakdown, please take a remedial action following the diagnosis based on the Engine Troubleshooting (Table 3) information shown below and on the proceeding page. If the problem cannot be remedied, please leave the unit just as it is and consult our company's business office or service TABLE 3.
MS-40H HYDRAULIC MIXER — TROUBLESHOOTING (ENGINE/MIXER) TABLE 3. ENGINE TROUBLESHOOTING (CONTINUED)) SYMPTOM Insufficient power output "compression" and overheats Burns to much fuel Exhaust color is continiously "WHITE" Exhaust color is continiously "BLACK" POSSIBLE PROBLEM SOLUTION Malfunction in cooling fan? Check or replace cooling fan. Air in-take filter clogged? Clean or replace air in-take filter. Over accumulation of exhaust products? Clean and check valves.
MS-40H HYDRAULIC MIXER — NOTE PAGE STOW MS-40H HYDRAULIC MIXER — PARTS & OPERATION MANUAL — REV.
EXPLANATION OF CODE IN REMARKS COLUMN How to read the marks and remarks used in this parts book. Section 1: Items Found In the “Remarks” Column Serial Numbers-Where indicated, this indicates a serial number range (inclusive) where a particular part is used. Model Number-Where indicated, this shows that the corresponding part is utilized only with this specific model number or model number variant.
MS-40H HYDRAULIC MIXER— SUGGESTED SPARE PARTS MS40H 1 TO 3 UNITS MS40H 5 TO 10 UNITS Qty. P/N Description 6 ............ 491010 ............ RUBBER LATCH ASSY. 1 ............ EM200293 ....... PADDLE ARM TOW SIDE 1 ............ EM200294 ....... PADDLE ARM CENTER TOW SIDE 1 ............ EM200295 ....... PADDLE ARM CENTER ENGINE SIDE 1 ............ EM200296 ....... PADDLE ARM ENGINE SIDE 3 ............ EM200863 ....... RUBBER BLADE KIT (STEEL DRUM) 2 ............ EM200297 ....... U-BOLT 2 ............
MS-40H HYDRAULIC MIXER — NAME PLATE AND DECALS NAME PLATE AND DECALS PAGE 24 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV.
MS-40H HYDRAULIC MIXER — NAME PLATE AND DECALS NAME PLATE AND DECALS NO PART NO PART NAME 1 2 3 4 5 6 7 DECAL : CAUTION DECAL : SAFETY INSTRUCTIONS PLATE, SERIAL NO............................. DECAL : MQ STOW DECAL : INSPECT TOWING DECAL : DUMP CONTROL DECAL : DRIVE CONTROL * * * * * * EM948423 924801 TBD DCL151 13238 511764 QTY. REMARKS 2 1 1 ........ CONTACT MQ PARTS DEPT. W/MODEL & S/N 1 2 1 1 SEE DECAL ILLUSTRATIONS ON PAGE 6. STOW MS-40H HYDRAULIC MIXER — PARTS & OPERATION MANUAL — REV.
MS-40H HYDRAULIC MIXER — ENGINE END PADDLE ASSY. ENGINE END PADDLE ASSY. PAGE 26 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV.
MS-40H HYDRAULIC MIXER — ENGINE END PADDLE ASSY. ENGINE END PADDLE ASSY.
MS-40H HYDRAULIC MIXER — TOW END PADDLE ASSY. TOW END PADDLE ASSY. PAGE 28 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV.
MS-40H HYDRAULIC MIXER — TOW END PADDLE ASSY. TOW END PADDLE ASSY.
MS-40H HYDRAULIC MIXER — STEEL MIXING DRUM ASSY. STEEL MIXING DRUM ASSY. PAGE 30 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV.
MS-40H HYDRAULIC MIXER — STEEL MIXING DRUM ASSY. STEEL MIXING DRUM ASSY.
MS-40H HYD. MIXER — PADDLE SHAFT ASSY. STEEL PADDLE SHAFT ASSY. PAGE 32 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV.
MS-40H HYD. MIXER — PADDLE SHAFT ASSY. STEEL PADDLE SHAFT ASSY. NO PART NO PART NAME 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 3061 3494 3019 3024 13002 3131 EM902153 3347 13108 13156 3215 3047 8164 5028B 13257 13156 3530 SPACER 14 OUTER SEAL 2 INNER SEAL 4 SPRING 2 BEARING SEAL 2 O-RING 2 BALL BEARING 2 SPECIAL NUT 1 SPACER 1 COUPLER 1 HHCS 1/2-13 X 3.1/2" 1 SPACER 1 CASTLE NUT 1-20 1 COTTER PIN 1 PADDLE SHAFT 1 DRIVE COUPLER 1 PADDLE SHAFT SEAL KIT .................................... 1 ....
MS-40H HYDRAULIC MIXER — HYDRAULIC ASSY. HYDRAULIC ASSY. PAGE 34 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV.
MS-40H HYDRAULIC MIXER — HYDRAULIC ASSY. HYDRAULIC ASSY. NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 PART NO 3323 3365 13243 3231 3242 10133 3327 0131A 0181B 3353 3369 10136 13198 13153 13196 3367 3462 0857 8051 8163 3461 3333 13219 13220 13210 13213 13147 3336 3215 13156 3322 1284 0166A 3316 13217 10176 3321 3314 13244 13216 510263 13225 13226 13212 3407 10477 PART NAME QTY.
MS-40H HYDRAULIC MIXER — FRAME 3 ASSY. FRAME 3 ASSY. 5 LUG HUB AND WHEEL (1-1/16 AXLE SPINDLE) S/N GE21000 - PAGE 36 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV.
MS-40H HYDRAULIC MIXER — FRAME 3 ASSY. FRAME 3 ASSY. 5 LUG HUB AND WHEEL (1-1/16 AXLE SPINDLE) NO PART NO PART NAME 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 15 15 16 17 18 19 20 21 22 23 24 25 26 27 28 30 31 13212 EM941280 13365Y 10133 0447 10176 511493Y 1023 13280Y 3102Y EM941278 3148 3028 3215 HLC-1 HPC-1 HBC-1 511699 5218 3043 3076 3018 19045 EM968302 0183 EM923161 EM903168 EM903169 EM914324 EM941277 EM903113 EM903012 GROMMET ............................................................. 1 ....
MS-40H HYDRAULIC MIXER — ENGINE COVER ASSY. ENGINE COVER ASSY. PAGE 38 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV.
MS-40H HYDRAULIC MIXER — ENGINE COVER ASSY. ENGINE COVER ASSY. NO PART NO PART NAME 1 2 3 4 5 6 ENGINE COVER-STEEL LATCH PIN ASSY. RUBBER LATCH ASSY. SCREW, HHCS 3/8-16 X 1.1/2” FLAT WASHER 3/8” LOCK NUT 3/8-16 511580Y 509726Y 491010 1284 4001 10133 QTY. REMARKS 1 2 2 4 8 4 STOW MS-40H HYDRAULIC MIXER — PARTS & OPERATION MANUAL — REV.
MS-40H HYDRAULIC MIXER — ENGINE ASSY. ENGINE ASSY. PAGE 40 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV.
MS-40H HYDRAULIC MIXER — ENGINE ASSY. ENGINE ASSY. NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 PART NO GX390K1QX2 3396 10133 1475 1665 10136 0310 0622C 3325 2126 13374 3419 3418 3420 0166A 1023 EM203149 PART NAME HONDA ENGINE 13 HP KILL BUTTON LOCK NUT 3/8-16 WIRE CONNECTOR HHCS 3/8-16 X 2" FLAT WASHER 3/8" SQ. KEY 1/4 X 1/4 X 1.1/2" SHSS 5/16-18 X 1/2" PUMP MOUNT SQ.
MS-40H HYDRAULIC MIXER — 1f- 5 HP ELECTRIC MOTOR ASSY. SINGLE PHASE, 5 HP ELECTRIC MOTOR ASSY. PAGE 42 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV.
MS-40H HYDRAULIC MIXER — 1f- 5 HP ELECTRIC MOTOR ASSY. SINGLE PHASE, 5 HP ELECTRIC MOTOR ASSY. NO 1 2 3 4 5 6 7 8 9 * 10 11 12 13 14 15 16 17 18 19 20 21 22 23 PART NO 3414 1023 0166A 0205 13291 8133 0310 0622C 940228 940198 13292 3421 3418 3420 3416 5054A 2691 13375 2203 10019 8156 10136 1665 10133 PART NAME QTY.
MS-40H HYDRAULIC MIXER — 3f- 5 HP ELECTRIC MOTOR ASSY. THREE PHASE, 5 HP ELECTRIC MOTOR ASSY. PAGE 44 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV.
MS-40H HYDRAULIC MIXER — 3f- 5 HP ELECTRIC MOTOR ASSY. THREE PHASE, 5 HP ELECTRIC MOTOR ASSY. NO PART NO PART NAME 1 2 3 4 5 6 7 8 9 3481 1023 0166A 0205 13291 8133 0310 0622C 940228 940198 13289 3421 3418 3420 3416 5054A 2691 13375 2203 10019 5 HP ELECTRIC MOTOR (THREE PHASE) 1 SCREW, HHCS 3/8-16 X 1-1/4 2 LOCK WASHER 3/8 4 SCREW, HHCS 3/8-16 X 1 2 SWITCH MOUNTING PLATE 1 SCREW, RHMS 8-32 X 3/4 3 SQUARE KEY 1/4 X 1/4 X 1-1/2 1 SCREW, 5/16 -18 X 1/2 2 SWITCH BOX (3 PHASE) 1 HEATER ELEMENT .............
TERMS AND CONDITIONS OF SALE — PARTS Effective: July 1, 2000 PAYMENT TERMS 4. Terms of payment for parts are net 10 days. FREIGHT POLICY All parts orders will be shipped collect or prepaid with the charges added to the invoice. All shipments are F.O.B. point of origin. Multiquip’s responsibility ceases when a signed manifest has been obtained from the carrier, and any claim for shortage or damage must be settled between the consignee and the carrier. Freight is at the sender’s expense.
NOTE PAGE STOW MS-40H HYDRAULIC MIXER — PARTS & OPERATION MANUAL — REV.
PARTS AND OPERATION MANUAL HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING PARTS DEPARTMENT 800-427-1244 or 310-537-3700 FAX: 800-672-7877 ^^^^^*^^^^^^^^^^^^^^^^^^^^^^^^^*^6668 or 310-637-3284 SERVICE DEPARTMENT/TECHNICAL ASSISTANCE 800-478-1244 or 310-537-3700 FAX: 310- 537-4259 WARRANTY DEPARTMENT 888-661-4279, or 310-661-4279 FAX: 310- 537-1173 MAIN 800-421-1244 or 310-537-3700 FAX: 310-537-3927 MULTIQUIP INC.
