StorCase® Technology InfoStation® Remote Diagnostics (SNMP) Module User's Guide
i StorCase® Technology InfoStation® Remote Diagnostics (SNMP) Module User's Guide Part No. D89-0000-0234 A00 July 2003 StorCase Technology, Inc. 17600 Newhope Street Fountain Valley, CA 92708-9885 Phone (714) 438-1850 Fax (714) 438-1847 InfoStation SNMP Module User's Guide - Rev. A00 StorCase Technology, Inc.
ii LIMITED WARRANTY STORCASE TECHNOLOGY, Incorporated (StorCase) warrants that its products will be free from defects in material and workmanship, subject to the conditions and limitations set forth below. StorCase will, at its option, either repair or replace any part of its product that proves defective by reason of improper workmanship or materials.
iii Free Technical Support StorCase provides free technical support. If you experience any difficulty during the installation or subsequent use of a StorCase product, please contact StorCases Technical Support Department prior to servicing your system. This warranty covers only repair or replacement of defective StorCase products, as described above. StorCase is not liable for, and does not cover under warranty, any costs associated with servicing and/or installation of StorCase products.
iv Declaration of Conformity Company Name: StorCase Technology, Inc.
v Federal Communications Commission (FCC) Statement RADIO FREQUENCY INTERFERENCE STATEMENT You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate that equipment. This device complies with part 15 of the FCC rules.
vi Table of Contents INTRODUCTION ..................................................................................................................... Packaging Information .................................................................................................. Serial Number ................................................................................................................ General Description ...........................................................................................
Introduction 1 INTRODUCTION Packaging Information The StorCase Technology InfoStation SNMP Module is shipped in a container designed to provide protection and prevent damage during shipment, as confirmed by the International Safe Transit Association (ISTA Procedure 1A). The module was carefully inspected before and during the packing procedure at the factory. Evidence of any damage to the module should be reported to the shipper immediately.
2 Introduction General Description CAUTION: The SNMP Module contains NO USER SERVICEABLE parts inside the unit. Refer ALL servicing to qualified service personnel! NOTES: The configuration and use of the StorCase InfoStation SNMP Module requires a certain level of expertise and experience on the part of the user/ integrator. Since there are many configuration options and variables (ie. host platforms, applications, etc.
Introduction 3 Features: Allows monitoring of chassis environmental parameters and component statuses (drive bays, power supplies, cooling modules, I/O repeater modules, RAID modules, SAF-TE processor boards) Compatible with third party management software (ie. HP Openview, CA Unicenter, IBM NetView, SunNet Manager) Complies with IEEE 802.3i 10BASE-T, IEEE 802.
4 Introduction Front Panel (Figure 2) RJ-45 UTP Port - Connects to 10BASE-T/100BASE-TX network. NOTE: SNMP Module supports 10Mbps only. LEDs - Provide the following information: Activity - ON = Indicates transmission and receiving of data. Link - ON = OFF= Indicates valid network connection. Indicates no network connection/link. If there is no link (LED is OFF): - Make sure power is ON at both ends of the network connection.
SNMP Configurations 5 CONFIGURATION CAUTION: The SNMP Module contains NO USER SERVICEABLE parts inside the unit. Refer ALL servicing to qualified service personnel! NOTES: The configuration and use of the StorCase InfoStation SNMP Module requires a certain level of expertise and experience on the part of the user/ integrator. Since there are many configuration options and variables (ie. host platforms, applications, etc.
6 SNMP Configurations Set-Up NOTES: Default Static IP address = 192.168.1.24 Default Submask address = 255.255.255.0 InfoMon must be at least Rev. 3.1 or higher to change the SNMP Module IP address. The latest InfoStation UI firmware can be downloaded from the StorCase web site. Refer to the InfoMon User's Guide for further information. StorCase recommends the use of Static IP addresses when configuring the SNMP Module. A default Static IP address has already be assigned to the module.
SNMP Configurations 7 SNMP Management Software The InfoStation SNMP Module must be used in conjunction with third party SNMP management software (such as HP Openview for example). Refer to your SNMP software manufacturer's documentation for further information. MIB (Management Information Base) StorCase MIB file(s) must be loaded and compiled using the third party SNMP management software (MIB compiler is included with software).
8 SNMP Configurations This Page Left Blank Intentionally. StorCase Technology, Inc. InfoStation SNMP Module User's Guide - Rev.
Reader's Comments 9 Reader's Comments Please take a few moments when your computer system is up and running to send us your ideas and suggestions for improving our products and documentation.
Reader's Comments CUT ALONG THIS LINE FROM BOTTOM TO TOP OF PAGE 10 FOLD ALONG THIS LINE AND STAPLE SHUT NO POSTAGE NECESSARY IF MAILED IN THE UNITED STATES B U S I N E S S R E P LY M A I L FIRST CLASS MAIL PERMIT NO. 10686 SANTA ANA, CA POSTAGE WILL BE PAID BY ADDRESSEE TECHNOLOGY CORPORATION 17600 NEWHOPE STREET FOUNTAIN VALLEY CA 92708-9885 StorCase Technology, Inc. InfoStation SNMP Module User's Guide - Rev.
