StorCase® Technology Rhino®JR RJR110 Serial ATA Removable Drive Enclosure User's Guide Part No. D89-0000-0254 A02 July 2005 StorCase Technology, Inc.
1 LIMITED WARRANTY STORCASE TECHNOLOGY, Incorporated (StorCase) warrants that its products will be free from defects in material and workmanship, subject to the conditions and limitations set forth below. StorCase will, at its option, either repair or replace any part of its product that proves defective by reason of improper workmanship or materials.
2 Warranty Claim Requirements To obtain warranty service, the defective product must be returned to your local authorized StorCase dealer or distributor, or, with prior StorCase approval, to the StorCase factory service center. For defective products returned directly to StorCase, a Return Material Authorization (RMA) number must be obtained by calling StorCase Customer Service at (714) 445-3455. The RMA number must be prominently displayed on the outside of the return package.
3 Declaration of Conformity Company Name: StorCase Technology, Inc. Corporate Office Address: 17600 Newhope Street Fountain Valley, CA 92708 Product Name: RhinoJr.
4 INTRODUCTION WARNING: The RhinoJR contains NO USER SERVICEABLE PARTS inside the unit. Refer ALL servicing to qualified service personnel! The StorCase Technology RhinoJR RJR110 removable drive carrier and receiving frame provides low cost, durable and reliable mounting for 3.5 Serial ATA drives within 5.25 half-height peripheral slots.
5 Front Panel (Figure 2) Key Lock/Drive Power Switch - Performs three functions. The key switch assures proper seating of the drive carrier within the receiving frame, turns power to the drive carrier ON and OFF, and prevents unauthorized removal or installation of the carrier. For the computer to access data on the disk drive, the key must be turned counterclockwise to the locked position. LEDs: Power - Steady glow indicates power ON.
6 Rear Panel (Figure 3) DC Power Connector: Standard 4-pin DC Power Connector to accept DC power. SATA Power Connector: Alternative 15-pin SATA Power Connector to accept DC power. I/O Connector: The input/output connector provides a standard interface for all Serial ATA signals. Activity Indicator: This pin is used for host connection (cable included) to the Activity Indicator.
7 Activity Indicator Cable (Figure 4) This cable (provided) is used for host connection to the Activity Indicator Pin. Some Serial ATA host controllers and system motherboards provide support for the Activity Indicator feature (refer to the Serial ATA host controller or system motherboard manufacturer's documentation for further information). Refer to Figure 3 for Activity Indicator Pin location.
8 INSTALLATION NOTE: A #1 and #2 Phillips screwdriver will be required for this procedure. 1. Remove cover from the carrier by turning screw clockwise. Slide the cover off carrier (Figure 5). 2. Carefully insert drive (not included) into the carrier. Turn the drive/carrier assembly over. 3. Bottom-mount the drive into the carrier with four (4) Phillips screws (Figure 6). Reinstall cover onto the carrier. Secure the cover by turning the screw counterclockwise a few rotations only.
9 Insert SATA Drive (Not Included) Bottom-Mount Drive Figure 6: Installing a Drive into the Carrier RJR110 Users Guide - Rev. A02 StorCase Technology, Inc.
10 Installing the Receiving Frame NOTE: Your Serial ATA host controller or system motherboard may provide support for the Activity Indicator feature (refer to the Serial ATA host controller or system motherboard manufacturers documentation for further information). Refer to Figures 3 & 4 for further information. The drive should be installed into the carrier before installing the receiving frame into the mounting bay of a computer or expansion chassis. 1.
11 SPECIFICATIONS These specifications are for reference only. Environmental Specifications Operating Ambient Temperature Relative Humidity (1) Altitude (1) (2) Storage -40° C to 70° C 15% to 90% -1000 to 40,000 ft -305m to 12195m Non-condensing with maximum gradient of 10% per hour 11 msec pulse width 1/2 sine wave Physical Specifications (1) 0° C to 40° C 20% to 80% -1000 to 10,000 ft -305m to 3048m Receiving Frame Height 1.65" (42mm) Width 5.75" (146mm) Depth 7.56" (192mm) Weight 1.
