StorCase® Technology Rhino JR FJR110 ® 1-Bay External Ultra320 Expansion Chassis User's Guide Part No. D89-0000-0264 A03 July 2005 StorCase Technology, Inc.
1 LIMITED WARRANTY STORCASE TECHNOLOGY, Incorporated (StorCase) warrants that its products will be free from defects in material and workmanship, subject to the conditions and limitations set forth below. StorCase will, at its option, either repair or replace any part of its product that proves defective by reason of improper workmanship or materials.
2 Warranty Claim Requirements To obtain warranty service, the defective product must be returned to your local authorized StorCase dealer or distributor, or, with prior StorCase approval, to the StorCase factory service center. For defective products returned directly to StorCase, a Return Material Authorization (RMA) number must be obtained by calling StorCase Customer Service at (714) 445-3455. The RMA number must be prominently displayed on the outside of the return package.
3 Declaration of Conformity Company Name: StorCase Technology, Inc. Corporate Office Address: 17600 Newhope Street Fountain Valley, CA 92708 Product Name: RhinoJr.
4 INTRODUCTION WARNING: The RhinoJR contains NO USER SERVICEABLE PARTS inside the unit. Refer ALL servicing to qualified service personnel! The StorCase® Technology RhinoJR FJR110 1-bay SCSI Ultra320 external expansion chassis provides low cost, rugged and reliable housing for 3.5 half-height storage devices. The RhinoJR is constructed of rugged steel and polycarbonate.
5 Front Panel (Figure 2) Power Switch: Controls power to the chassis. LEDs: Power (Green) Steady glow indicates power ON. Drive Activity (Amber) Flashing indicates drive is being accessed. Power Switch Drive Activity LED Power LED Figure 2: Front Panel FJR110 Users Guide - Rev. A03 StorCase Technology, Inc.
6 Rear Panel (Figure 3) A/C Power In: Accepts U.S. and other available international standrard power cables. Contact StorCase for further ordering information. I/O Connector: The HD68 I/O connector provides a standard interface for SCSI Ultra320 signals. SCSI ID Select Switch: Provides SCSI ID selection (refer to section Selecting the SCSI ID Number for further information). Cooling Fan: Fan provides ample chassis ventilation (9.5 CFM).
7 INSTALLATION CAUTION: Remove ALL power from the RhinoJR before removing the cover. The RhinoJR chassis contains NO USER SERVICEABLE parts inside the unit. Refer ALL servicing to qualified personnel! NOTES: A #2 Phillips screwdriver will be required for this procedure. Refer to the disk manufacturer's documentation for specific information regarding the disk. Removing the RhinoJR Cover and Access Panel 1. Unplug chassis and verify that ALL cables have been disconnected. 2.
8 3. Carefully lift up the rear end of the access panel and slide off chassis (Figure 5). Lift This End Slightly and Slide Access Panel Off Figure 5: Removing the Access Panel StorCase Technology, Inc. FJR110 Users Guide - Rev.
9 Installing the Drive into the Chassis NOTES: Removal of chassis cover and access panel are required to install the drive. Refer to your drive manufacturer's documentation for further information. 1. Carefully insert drive (not included) into the chassis (Figure 6A). 2. Connect the 2-wire drive activity cable to the drive (refer to the drive manufacturers documentation for the location of these pins). 3.
10 Typical Drive 16-Bit SCSI ID Select Pins (Pins vary on each drive model. Refer to your drive manufacturers documentation for further information.) Signal Row 3 GND Row 21 0 B B lack Red rown (ID0) ( ID2 (ID1) Bla ) Ora ck (G nge ND) (ID3 ) ID Select Cable from Chassis ID Select Connector Figure 6B: 16-Bit SCSI ID Cable Connection StorCase Technology, Inc. FJR110 Users Guide - Rev.
11 6. Carefully turn the chassis over and bottom-mount the drive with four (4) #6-32 Phillips or M3 screws (both provided) as shown in Figure 7. 7. Reinstall access panel and cover onto the chassis. Cover may be secured to the chassis using two (2) Phillips M3 Flat Hd. screws (provided). Bottom-Mount Drive with 4 Screws Figure 7: Bottom-Mounting the Drive FJR110 Users Guide - Rev. A03 StorCase Technology, Inc.
12 Selecting the SCSI ID Number The SCSI ID selection switch is located on the rear panel of the chassis (Figure 2). Carefully select the appropriate SCSI ID number for the installed device as shown. Switch can be adjusted with either the tip of a pen or a straightened paper clip. Note that some switch settings may be invalid for your interface type.
13 SPECIFICATIONS The following RhinoJR specifications are for reference only. 0 C to 40 C -40 C to 70 C -1000 to 10,000 ft -1000 to 40,000 ft -305m to 3048m -305m to 12195m 2.36 (60.0mm) 7.56 (192.0mm) 9.76 (248.0mm) 3.2 lbs (1.45kg) Weight empty (without drive installed) (1) Auto-ranging 34W (40W Peak) Power Supply 100 to 240 VAC, 47-63Hz at 1.0A Max 5V at 2.0A, 12V at 2.0A DC Output Continuous 220,000 Hours NOTICE: Total (For 1 Fan) 9.
