Datasheet

ManualsBrandsSTMICROELECTRONICS ManualsPMICsPMIC - ELCs High side BSSOP 36

This is information on a product in full production.

December 2013 DocID11455 Rev 12 1/22

VN808-E

Octal channel high-side driver

Datasheet

production data

Features

• V

/2 compatible input

• Junction overtemperature protection

• Case overtemperature protection for thermal

independence of the channels

• Current limitation

• Short-circuit load protection

• Undervoltage shutdown

• Protection against loss of ground

• Very low standby current

• Compliance to 61000-4-4 IEC test up to 4 kV

Description

The VN808-E is a monolithic device, realized in

STMicroelectronics VIPower M0-3 technology,

intended to drive any kind of load with one side

connected to ground. Active current limitation

combined with thermal shutdown and automatic

restart, protect the device against overload. In

overload conditions, the channel turns OFF and

ON again automatically in order to maintain the

junction temperature between T

TSD

and T

. If

this

condition makes case temperature reach T

CSD

overloaded channels are turned OFF and restart

only when case temperature decreases down to

. Non-overloaded channels continue to

operate normally. The device automatically turns

OFF in case of ground pin disconnection. This

device is especially suitable for industrial

applications conform to IEC 61131.

Figure 1. Internal schematic

Type R

DS(on)

(1)

1. Per channel

OUT

VN808-E 150 mΩ 0.7 A 45 V

PowerSO-36

www.st.com

Summary of content (22 pages)

PAGE 1
VN808-E Octal channel high-side driver Datasheet - production data • Protection against loss of ground • Very low standby current • Compliance to 61000-4-4 IEC test up to 4 kV Description PowerSO-36 Features Type RDS(on)(1) IOUT VCC VN808-E 150 mΩ 0.7 A 45 V 1.
PAGE 2
Contents VN808-E Contents 1 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Pin connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4 Current, voltage conventions and internal diagram . . . . . . . . . . . . . . . 8 5 Switching time waveforms . . . . . . . . . . . . . . . . . . . . .
PAGE 3
VN808-E 1 Maximum ratings Maximum ratings Table 1. Absolute maximum ratings Symbol Parameter VCC DC supply voltage -IGND DC ground reverse current TRAN ground reverse current (pulse duration < 1 ms) IOUT DC output current -IOUT Reverse DC output current IIN DC input current VIN Input voltage range VESD Electrostatic discharge (R = 1.
PAGE 4
Electrical characteristics 2 VN808-E Electrical characteristics 10.5 V < VCC < 32 V; - 40 °C < TJ < 125 °C; unless otherwise specified. Table 3. Power section Symbol Parameter Test conditions VCC Operating supply voltage VUSD Undervoltage shutdown RON On-state resistance IOUT = 0.5 A; TJ = 25 °C IOUT = 0.
PAGE 5
VN808-E Electrical characteristics Table 5. Input pin Symbol Parameter VINL Input low level IINL Low level input current VINH Input high level IINH High level input current VI(HYST) Input hysteresis voltage IIN Input current Test conditions Min. VIN = VCC / 2 - 1 V Typ. 80 Max. Unit VCC /2-1 V 650 μA VCC /2+1 VIN = VCC / 2 + 1 V V 150 260 0.6 VIN = VCC = 32 V μA V 300 μA Table 6. Protection Symbol Parameter Test conditions Min. Typ. Max.
PAGE 6
Pin connections 3 VN808-E Pin connections Figure 2. Connection diagram (top view) Table 8.
PAGE 7
VN808-E Pin connections Table 8. Pin functions (continued) Pin Symbol Function 27.
PAGE 8
Current, voltage conventions and internal diagram 4 VN808-E Current, voltage conventions and internal diagram Figure 3. Current and voltage conventions Figure 4. Equivalent internal block diagram (same structure for all channels) VCC STATUS 52V 6.
PAGE 9
VN808-E Current, voltage conventions and internal diagram Figure 5. Application example Filter for bus inductance effect, make supply voltage stable and avoid undervoltage shut down Protection for IEC 61000-4-5 Surge test EMC Filter + 22 µF Vcc 100nF Vin 1 Load 1 Load 2 Vin 2 Load 3 Vin 3 VN 808 - E Vin 8 Status Load 8 10nF Protection against IEC 61000-4-6 Current injection test RGND AM16519v1 Table 9.
PAGE 10
Switching time waveforms 5 VN808-E Switching time waveforms Figure 6. Turn-ON and turn-OFF Figure 7.
PAGE 11
VN808-E Switching time waveforms Figure 8.
PAGE 12
Switching time waveforms VN808-E Figure 9.
PAGE 13
VN808-E 6 Reverse polarity protection Reverse polarity protection Reverse polarity protection can be implemented on board using two different solutions: 1. Placing a resistor (RGND) between IC GND pin and load GND 2.
PAGE 14
Package mechanical data 7 VN808-E Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com. ECOPACK is an ST trademark. Figure 11.
PAGE 15
VN808-E Package mechanical data Table 10. PowerSO-36 mechanical data mm Dim. Min. Typ. A a1 Max. 3.60 0.10 0.30 a2 3.30 a3 0 0.10 b 0.22 0.38 c 0.23 0.32 D (1) 15.80 16.00 D1 9.40 9.80 E 13.90 14.50 E1 (1) 10.90 11.10 E2 E3 2.90 5.8 6.2 e 0.65 e3 11.05 G 0 0.10 H 15.50 15.90 h L 1.10 0.80 N S 1.
PAGE 16
Package mechanical data 7.1 VN808-E Footprint recommended data Figure 12. Footprint recommended data Table 11. Footprint data 16/22 Dim. mm A 9.5 B 14.7-15.0 C 12.5-12.7 D 6.3 E 0.42 G 0.
PAGE 17
VN808-E 7.2 Package mechanical data Tube shipment information Figure 13. Tube shipment information Table 12. Tube mechanical data Dim. mm A 18.80 B 17.2 ±0.2 C 8.20 ±0.2 D 10.90 ±0.2 E 2.90 ±0.2 F 0.40 G 0.80 H 6.30 I 4.30 ±0.2 J 3.7 ±0.2 K 9.4 L 0.40 M 0.80 N 3.50 ±0.
PAGE 18
Package mechanical data 7.3 VN808-E Tape and reel shipment information Figure 14. Tape specifications % ,P 1 1P & ' 3 #P 8 3 5 $ "P 1 #FOEJOH SBEJVT 6TFS EJSFDUJPO PG GFFE 6TFS EJSFDUJPO PG GFFE Table 13. Tape mechanical data Dim. mm D 1.50 +0.1/0 E 1.75 ±0.1 Po 4.00 ±0.1 T max. 0.40 D1 min. 1.50 F 11.5 ±0.05 K max. 6.50 P2 2.00 ±0.1 R 50 W 24.00 ±0.30 P1 24.00 Ao, Bo, Ko 0.05 min. to 1.0 max.
PAGE 19
VN808-E Package mechanical data Figure 15. Reel specifications 7 PP LQ PLQ DFFHVV KROH DW VORW ORFDWLRQ % & ' $ 1 * PHDVXUHG DW KXE )XOO UDGLXV 7DSH VORW LQ FRUH IRU WDSH VWDUW PP LQ PLQ ZLGWK Table 14. Reel mechanical data Dim. mm Tape size 24.0 ±0.30 A max. 330.0 B min. 1.5 C 13.0 ±0.20 D min. 20.2 N min. 60 G 24.4 +2/-0 T max. 30.
PAGE 20
Ordering information 8 VN808-E Ordering information Table 15.
PAGE 21
VN808-E 9 Revision history Revision history Table 16. Document revision history Date Revision Changes 13-Sep-2005 1 Initial release 1-Mar-2007 2 Document reformatted 12-Mar-2007 3 Typo in Figure 3. 26-Mar-2007 4 Typo note Table 2.
PAGE 22
VN808-E Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale.