TSV991, TSV992, TSV994, TSV991A, TSV992A, TSV994A Rail-to-rail input/output 20 MHz GBP operational amplifiers Datasheet − production data Features ■ Low input offset voltage: 1.5 mV max (A grade) ■ Rail-to-rail input and output ■ Wide bandwidth 20 MHz ■ Stable for gain ≥ 4 or ≤ -3 ■ Low power consumption: 820 µA typ ■ High output current: 35 mA ■ Operating from 2.5 V to 5.5 V ■ Low input bias current, 1 pA typ ■ ESD internal protection ≥ 5 kV Pin connections (top view) SOT23-5 /54 6## ).
Contents TSV99x, TSV99xA Contents 1 Absolute maximum ratings and operating conditions . . . . . . . . . . . . . 3 2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3 Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 4 3.1 Driving resistive and capacitive loads . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 3.2 PCB layouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TSV99x, TSV99xA 1 Absolute maximum ratings and operating conditions Absolute maximum ratings and operating conditions Table 1. Absolute maximum ratings Symbol VCC Vid Vin Iin Parameter (1) Supply voltage Differential input voltage (2) Value Unit 6 V ±VCC V (3) VCC- -0.2 to VCC+ +0.
Absolute maximum ratings and operating conditions Table 2. Operating conditions Symbol 4/25 TSV99x, TSV99xA Parameter VCC Supply voltage Vicm Common mode input voltage range Top Operating free air temperature range Doc ID 12833 Rev 9 Value Unit 2.5 to 5.5 V VCC- -0.1 to VCC+ +0.
TSV99x, TSV99xA Electrical characteristics 2 Electrical characteristics Table 3. Electrical characteristics at VCC+ = +2.5 V, VCC- = 0 V, Vicm = VCC/2, with RL connected to VCC/2, full temperature range (unless otherwise specified)(1) Symbol Parameter Conditions Min. Typ. Max. 0.1 4.5 Unit DC performance Offset voltage TSV99x Vio Offset voltage TSV99xA Top = 25° C Tmin < Top < Tmax 7.5 Top = 25° C 1.
Electrical characteristics Table 3. Electrical characteristics at VCC+ = +2.5 V, VCC- = 0 V, Vicm = VCC/2, with RL connected to VCC/2, full temperature range (unless otherwise specified)(1) Symbol en TSV99x, TSV99xA Parameter Equivalent input noise voltage THD+N Total harmonic distortion Conditions Min. f = 10 kHz, Top = 25° C Typ. Max. nV -----------Hz 21 G = -3, f = 1 kHz, RL = 2 kΩ, Bw = 22 kHz, Vicm = VCC/2, Vout = 2 Vpp, Top = 25° C Unit 0.0025 % 1.
TSV99x, TSV99xA Table 4. Electrical characteristics Electrical characteristics at VCC+ = +3.3 V, VCC- = 0 V, Vicm = VCC/2, with RL connected to VCC/2, full temperature range (unless otherwise specified)(1) (continued) Symbol Parameter Conditions Min. Typ. Max.
Electrical characteristics Table 5. Electrical characteristics at VCC+ = +5 V, VCC- = 0 V, Vicm = VCC/2, RL connected to VCC/2, full temperature range (unless otherwise specified)(1) Symbol VCCVOH VOL TSV99x, TSV99xA Parameter Conditions High level output voltage Low level output voltage Isink Iout Isource ICC Supply current (per operator) Min. Typ. Max.
TSV99x, TSV99xA Electrical characteristics Figure 3. Supply current vs. input common mode voltage at VCC = 2.5 V Figure 4. Figure 5. Output current vs. output voltage at Figure 6. VCC = 2.5 V Doc ID 12833 Rev 9 Supply current vs. input common mode voltage at VCC = 5 V Output current vs.
Electrical characteristics Voltage gain and phase vs frequency at VCC = 5 V and Vicm = 0.5 V Figure 9. Positive slew rate Figure 8. Voltage gain and phase vs frequency at VCC = 5 V and Vicm = 2.5 V Figure 10. Negative slew rate Phase (°) Phase (°) Figure 7. TSV99x, TSV99xA Vin : from 0.5V to Vcc-0.5V SR : calculated from 10% to 90% Vin : from 0.5V to Vcc-0.5V SR : calculated from 10% to 90% Figure 11. Distortion + noise vs. frequency 10/25 Figure 12. Distortion + noise vs.
TSV99x, TSV99xA Figure 13. Noise vs. frequency Electrical characteristics Figure 14. Supply current vs.
Application information TSV99x, TSV99xA 3 Application information 3.1 Driving resistive and capacitive loads These products are low-voltage, low-power operational amplifiers optimized to drive rather large resistive loads above 2 kΩ.. TSV99x products are not unity gain stable. To ensure proper stability they must be used in a gain configuration, with a minimum gain of -3 or +4.
TSV99x, TSV99xA 3.3 Application information Macromodel An accurate macromodel of the TSV99x is available on STMicroelectronics’ web site at www.st.com. This model is a trade-off between accuracy and complexity (that is, time simulation) of the TSV99x operational amplifiers. It emulates the nominal performances of a typical device within the specified operating conditions mentioned in the datasheet.
Package information 4 TSV99x, TSV99xA Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark.
TSV99x, TSV99xA 4.1 Package information SOT23-5 package information Figure 17. SOT23-5 package mechanical drawing Table 6. SOT23-5 package mechanical data Dimensions Ref. A Millimeters Inches Min. Typ. Max. Min. Typ. Max. 0.90 1.20 1.45 0.035 0.047 0.057 A1 0.15 0.006 A2 0.90 1.05 1.30 0.035 0.041 0.051 B 0.35 0.40 0.50 0.013 0.015 0.019 C 0.09 0.15 0.20 0.003 0.006 0.008 D 2.80 2.90 3.00 0.110 0.114 0.118 D1 1.90 0.075 e 0.95 0.037 E 2.60 2.
Package information 4.2 TSV99x, TSV99xA DFN8 2x2 package information Figure 18. DFN8 2x2 package mechanical drawing $&.
TSV99x, TSV99xA Table 7. Package information DFN8 2x2 package mechanical data Dimensions Ref. A Inches(1) Millimeters Min. Typ. Max. Min. Typ. Max. 0.51 0.55 0.60 0.020 0.022 0.024 A1 0.05 A3 0.002 0.15 0.006 b 0.18 0.25 0.30 0.007 0.010 0.012 D 1.85 2.00 2.15 0.073 0.079 0.085 D2 1.45 1.60 1.70 0.057 0.063 0.067 E 1.85 2.00 2.15 0.073 0.079 0.085 E2 0.75 0.90 1.00 0.030 0.035 0.039 e 0.50 0.020 L 0.50 0.020 ddd 0.08 0.003 1.
Package information 4.3 TSV99x, TSV99xA MiniSO-8 package information Figure 20. MiniSO-8 package mechanical drawing Table 8. MiniSO-8 package mechanical data Dimensions Ref. Millimeters Min. Typ. A Max. Min. Typ. 1.1 A1 0 A2 0.75 b Max. 0.043 0.15 0 0.95 0.030 0.22 0.40 0.009 0.016 c 0.08 0.23 0.003 0.009 D 2.80 3.00 3.20 0.11 0.118 0.126 E 4.65 4.90 5.15 0.183 0.193 0.203 E1 2.80 3.00 3.10 0.11 0.118 0.122 e L 0.85 0.65 0.40 0.60 0.006 0.033 0.
TSV99x, TSV99xA 4.4 Package information SO-8 package information Figure 21. SO-8 package mechanical drawing Table 9. SO-8 package mechanical data Dimensions Ref. Millimeters Min. Typ. A Inches Max. Min. Typ. 1.75 0.069 A1 0.10 A2 1.25 b 0.28 0.48 0.011 0.019 c 0.17 0.23 0.007 0.010 D 4.80 4.90 5.00 0.189 0.193 0.197 E 5.80 6.00 6.20 0.228 0.236 0.244 E1 3.80 3.90 4.00 0.150 0.154 0.157 e 0.25 Max. 0.004 0.010 0.049 1.27 0.050 h 0.25 0.50 0.010 0.
Package information 4.5 TSV99x, TSV99xA TSSOP14 package information Figure 22. TSSOP14 package mechanical drawing Table 10. TSSOP14 package mechanical data Dimensions Ref. Millimeters Min. Typ. A Max. Min. Typ. 1.20 A1 0.05 A2 0.80 b Max. 0.047 0.15 0.002 0.004 0.006 1.05 0.031 0.039 0.041 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0089 D 4.90 5.00 5.10 0.193 0.197 0.201 E 6.20 6.40 6.60 0.244 0.252 0.260 E1 4.30 4.40 4.50 0.169 0.173 0.
TSV99x, TSV99xA 4.6 Package information SO-14 package information Figure 23. SO-14 package mechanical drawing Table 11. SO-14 package mechanical data Dimensions Millimeters Inches Ref. Min. Typ. Max. Min. Typ. Max. A 1.35 1.75 0.05 0.068 A1 0.10 0.25 0.004 0.009 A2 1.10 1.65 0.04 0.06 B 0.33 0.51 0.01 0.02 C 0.19 0.25 0.007 0.009 D 8.55 8.75 0.33 0.34 E 3.80 4.0 0.15 0.15 e 1.27 0.05 H 5.80 6.20 0.22 0.24 h 0.25 0.50 0.009 0.02 L 0.40 1.27 0.
Ordering information 5 TSV99x, TSV99xA Ordering information Table 12.
TSV99x, TSV99xA 6 Revision history Revision history Table 13. Document revision history Date Revision 31-Jul-2006 1 Preliminary data release for product under development. 07-Nov-2006 2 Final version of datasheet. 12-Dec-2006 3 Noise and distortion figures added. 4 ESD tolerance modified for SO-14, CDM in Table 1: Absolute maximum ratings. Automotive grade commercial products added in Table 12: Order codes. Note about SO-14 added in Table 12: Order codes.
Revision history TSV99x, TSV99xA Table 13. Document revision history Date 22-Oct-2012 24/25 Revision 9 cont’d Changes Figure 11 and Figure 12: updated. Added Figure 18: DFN8 2x2 package mechanical drawing and Figure 19: DFN8 2x2 footprint recommendation. Table 12: Order codes: updated automotive grade qualification and added order code of DFN8 package.
TSV99x, TSV99xA Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale.