Datasheet
Table Of Contents
- Table 1. Device summary
- 1 Package pin connections
- 2 Absolute maximum ratings and operating conditions
- 3 Electrical characteristics
- Table 4. Electrical characteristics at VCC+ = +2.7 V with VCC- = 0 V, Vicm = VCC/2, T = 25 C, and RL = 10 kW connected to VCC/2 (unless otherwise specified)
- Table 5. Electrical characteristics at VCC+ = +3.3 V with VCC- = 0 V, Vicm = VCC/2, T = 25 C, and RL = 10 kW connected to VCC/2 (unless otherwise specified)
- Table 6. Electrical characteristics at VCC+ = +5 V with VCC- = 0 V, Vicm = VCC/2, T = 25 C, and RL = 10 kW connected to VCC/2 (unless otherwise specified)
- Figure 2. Supply current vs. supply voltage at Vicm = VCC/2
- Figure 3. Input offset voltage distribution at VCC = 5 V, Vicm = 2.5 V
- Figure 4. Input offset voltage temperature coefficient distribution
- Figure 5. Input offset voltage vs. input common mode voltage at VCC = 5 V
- Figure 6. Input offset voltage vs. temperature at VCC = 5 V
- Figure 7. Output current vs. output voltage at VCC = 2.7 V
- Figure 8. Output current vs. output voltage at VCC = 5.5 V
- Figure 9. Bode diagram at VCC = 2.7 V, RL = 10 kW
- Figure 10. Bode diagram at VCC = 2.7 V, RL = 2 kW
- Figure 11. Bode diagram at VCC = 5.5 V, RL = 10 kW
- Figure 12. Bode diagram at VCC = 5.5 V, RL = 2 kW
- Figure 13. Noise vs. frequency
- Figure 14. Positive slew rate vs. supply voltage
- Figure 15. Negative slew rate vs. supply voltage
- Figure 16. THD+N vs. frequency at VCC = 2.7 V
- Figure 17. THD+N vs. frequency at VCC = 5.5 V
- Figure 18. THD+N vs. output voltage at VCC = 2.7 V
- Figure 19. THD+N vs. output voltage at VCC = 5.5 V
- Figure 20. Output impedance versus frequency in closed-loop configuration
- Figure 21. Response to a 100 mV input step for gain = 1 at VCC = 5.5 V rising edge
- Figure 22. Response to a 100 mV input step for gain = 1 at VCC = 5.5 V falling edge
- Figure 23. PSRR vs. frequency at VCC = 2.7 V
- Figure 24. PSRR vs. frequency at VCC = 5.5 V
- 4 Application information
- 5 Package information
- Figure 30. SC70-5 package outline
- Table 7. SC70-5 package mechanical data
- Figure 31. DFN8 2 x 2 x 0.6, 8 pitch, 0.5 mm package outline
- Table 8. DFN8 2 x 2 x 0.6, 8 pitch, 0.5 mm package mechanical data
- Figure 32. DFN8 2 x 2 0.6, 8 pitch, 0.5 mm footprint recommendation
- Figure 33. MiniSO8 package outline
- Table 9. MiniSO8 package mechanical data
- Figure 34. QFN16 - 3 x 3 x 0.9 mm, pad 1.7 - package outline
- Table 10. QFN16 - 3 x 3 x 0.9 mm, pad 1.7 - package mechanical data
- Figure 35. QFN16 - 3 x 3 x 0.9 mm, pad 1.7 - footprint recommendation
- Figure 36. TSSOP14 body 4.40 mm, lead pitch 0.65 mm - package outline
- Table 11. TSSOP14 body 4.40 mm, lead pitch 0.65 mm - package mechanical data
- 6 Ordering information
- 7 Revision history
TSV521, TSV522, TSV524, TSV521A, TSV522A, TSV524A
Doc ID 022743 Rev 1 27/27
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at an
y
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2012 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com