Datasheet
Table Of Contents
- 1 Absolute maximum ratings and operating conditions
- 2 Electrical characteristics
- Table 3. Electrical characteristics at VCC = +5 V, VDD = 0 V, Vicm = VCC/2, Tamb = 25 °C, RL connected to VCC/2 (unless otherwise specified)
- Table 4. Electrical characteristics at VCC = +3.3 V, VDD = 0 V, Vicm = VCC/2, Tamb = 25 °C, RL connected to VCC/2 (unless otherwise specified)
- Table 5. Electrical characteristics at VCC = +2.7 V VDD = 0 V, Vicm = VCC/2, Tamb = 25 °C, RL connected to VCC/2 (unless otherwise specified)
- Figure 1. Input offset voltage distribution for Vicm£ VCC-1.2 V at T=25 °C
- Figure 2. Input offset voltage distribution vs. temperature for Vicm£ VCC-1.2 V
- Figure 3. Input offset voltage distribution vs. temperature for Vicm ³ VCC-0.8 V
- Figure 4. Input offset voltage distribution for Vicm £ VCC-1.2 V at T=25 °C after HTB
- Figure 5. Input offset voltage distribution for Vicm £ VCC-1.2 V at T=25 °C after THB
- Figure 6. Input offset voltage vs. input common mode voltage at T=25 °C
- Figure 7. Supply current vs. input common mode voltage in closed loop configuration at VCC=5 V
- Figure 8. Supply current vs. supply voltage at Vicm=VCC/2
- Figure 9. Supply current vs. input common mode voltage in follower configuration at VCC=2.7 V
- Figure 10. Supply current vs. input common mode voltage in follower configuration at VCC=5 V
- Figure 11. Output current vs. supply voltage at Vicm=VCC/2
- Figure 12. Output current vs. output voltage at VCC=2.7 V
- Figure 13. Output current vs. output voltage at VCC=5 V
- Figure 14. Positive and negative slew rate vs. supply voltage
- Figure 15. Voltage gain and phase vs. frequency at VCC=5 V and Vicm=2.5 V at T=25 °C
- Figure 16. Voltage gain and phase vs. frequency at VCC=5 V and Vicm=2.5 V at T=-40 °C
- Figure 17. Voltage gain and phase vs. frequency at VCC=5 V and Vicm=2.5 V at T=125 °C
- Figure 18. Closed loop gain in voltage follower configuration for different capacitive load at T=25 °C
- Figure 19. Gain margin according to the output load, at VCC=5 V and T=25 °C
- Figure 20. Phase margin according to the output load, at VCC=5 V and T=25 °C
- Figure 21. Gain margin vs. output current, at VCC=5 V and T=25 °C
- Figure 22. Phase margin vs. output current, at VCC=5 V and T=25 °C
- Figure 23. Phase and gain margins vs capacitive load at = 25 °C
- Figure 24. Distortion + noise vs. output voltage
- Figure 25. Distortion + noise vs. frequency
- Figure 26. Noise vs. frequency
- 3 Application note
- 4 Package information
- 5 Ordering information
- 6 Revision history
DocID10958 Rev 6 17/20
TS507 Package information
4 Package information
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK
®
packages, depending on their level of environmental compliance. ECOPACK
®
specifications, grade definitions and product status are available at:
www.st.com.
ECOPACK
®
is an ST trademark.
4.1 SOT23-5 package information
Figure 31. SOT23-5 package mechanical drawing
Table 7. SOT23-5 package mechanical data
Ref.
Dimensions
Millimeters Mils
Min. Typ. Max. Min. Typ. Max.
A 0.90 1.45 35.4 57.1
A1 0.00 0.15 0.00 5.9
A2 0.90 1.30 35.4 51.2
b 0.35 0.50 13.7 19.7
C 0.09 0.20 3.5 7.8
D 2.80 3.00 110.2 118.1
E 2.60 3.00 102.3 118.1
E1 1.50 1.75 59.0 68.8
e 0.95 37.4
e1 1.9 74.8
L 0.35 0.55 13.7 21.6