Datasheet
Table Of Contents
- Table 1. Device summary
- 1 Schematic and pins connection diagrams
- 2 Electrical specifications
- 2.1 Absolute maximum ratings
- 2.2 Thermal data
- 2.3 Bridge amplifier section
- 2.4 Stereo amplifier application
- Figure 9. Typical stereo application circuit
- 2.4.1 Electrical characteristics (stereo application)
- Table 7. Electrical characteristics (stereo application)
- Figure 10. Quiescent output voltage vs. supply voltage (stereo amplifier)
- Figure 11. Quiescent drain current vs. supply voltage (stereo amplifier)
- Figure 12. Distortion vs. output power (stereo amplifier)
- Figure 13. Output power vs. supply voltage, RL = 2 and 4 W (stereo amplifier)
- Figure 14. Output power vs. supply voltage, RL = 1.6 and 3.2 W (stereo amplifier)
- Figure 15. Distortion vs. frequency, RL = 2 and 4 W (stereo amplifier)
- Figure 16. Distortion vs. frequency, RL = 1.6 and 3.2 W (stereo amplifier)
- Figure 17. Supply voltage rejection vs. C3 (stereo amplifier)
- Figure 18. Supply voltage rejection vs. frequency (stereo amplifier)
- Figure 19. Supply voltage rejection vs. C2 and C3, GV = 390/1 W (stereo amplifier)
- Figure 20. Supply voltage rejection vs. C2 and C3, GV = 1000/10 W (stereo amplifier)
- Figure 21. Gain vs. input sensitivity RL = 4 W (stereo amplifier)
- Figure 22. Gain vs. input sensitivity RL = 2 W (stereo amplifier)
- Figure 23. Total power dissipation and efficiency vs. output power (bridge)
- Figure 24. Total power dissipation and efficiency vs. output power (stereo)
- 3 Application suggestion
- 4 Application information
- Figure 25. Bridge amplifier without boostrap
- Figure 26. PC board and components layout of Figure 25
- Figure 27. Low cost bridge amplifier (GV = 42 dB)
- Figure 28. PC board and components layout of Figure 27
- Figure 29. 10 + 10 W stereo amplifier with tone balance and loudness control
- Figure 30. Tone control response (circuit of Figure 29)
- Figure 31. 20 W bus amplifier
- Figure 32. Simple 20 W two way amplifier (FC = 2 kHz)
- Figure 33. Bridge amplifier circuit suited for low-gain applications (GV = 34 dB)
- Figure 34. Example of muting circuit
- 4.1 Built-in protection systems
- 5 Package information
- 6 Revision history
TDA2005
Doc ID 1451 Rev 6 25/25
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE
SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B)
AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS
OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT
PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS
EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY
DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE
DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2013 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com