Datasheet

ManualsBrandsSTMICROELECTRONICS ManualsPMICsPMIC - system monitor Smart ON/OFF controller TDFN 12

This is information on a product in full production.

June 2012 Doc ID 15453 Rev 11 1/52

STM6600, STM6601

Smart push-button on/off controller with Smart Reset™ and

power-on lockout

Datasheet − production data

Features

■ Operating voltage 1.6 V to 5.5 V

■ Low standby current of 0.6 µA

■ Adjustable Smart Reset

™

assertion delay time

driven by external C

SRD

■ Power-up duration determined primarily by

push-button press (STM6600) or by fixed time

period, t

ON_BLANK

(STM6601)

■ Debounced PB and SR inputs

■ PB and SR ESD inputs withstand voltage up to

±15 kV (air discharge) ±8 kV (contact

discharge)

■ Active high or active low enable output option

(EN

or EN) provides control of MOSFET,

DC-DC converter, regulator, etc.

■ Secure startup, interrupt, Smart Reset

™

power-down driven by push-button

■ Precise 1.5 V voltage reference with 1%

accuracy

■ Industrial operating temperature –40 to +85 °C

■ Available in TDFN12 2 x 3 mm package

Applications

■ Portable devices

■ Termin

als

■

udio and video players

■ Cell phones and smart phones

■ PDAs, palmtops, organizers

TDFN12

Table 1. Device summary

Device RST C

SRD

PB / SR EN or EN INT Startup process

STM6600 open drain

(1)

✓✓push-pull open drain

(1)

PB must be held low until the

HOLD

(2)

confirmation

STM6601 open drain

(1)

✓✓push-pull open drain

(1)

PB can be released before the

HOLD

(2)

confirmation

1. External pull-up resistor needs to be connected to open drain outputs.

2. For a successful startup, the PS

HOLD

(Power Supply Hold) needs to be pulled high within specific time, t

ON_BLANK

www.st.com

Summary of content (52 pages)

PAGE 1
STM6600, STM6601 Smart push-button on/off controller with Smart Reset™ and power-on lockout Datasheet − production data Features ■ Operating voltage 1.6 V to 5.5 V ■ Low standby current of 0.
PAGE 2
Contents STM6600, STM6601 Contents 1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2 Pin descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 4 Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
STM6600, STM6601 List of tables List of tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Pin descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 4
List of figures STM6600, STM6601 List of figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. Figure 12. Figure 13. Figure 14. Figure 15. Figure 16. Figure 17. Figure 18. Figure 19. Figure 20. Figure 21. Figure 22. Figure 23. Figure 24. Figure 25. Figure 26. Figure 27. Figure 28. Figure 29. Figure 30. Figure 31. Figure 32. Figure 33. Figure 34. Figure 35. Figure 36. Figure 37. Figure 38. Figure 39. Figure 40. Figure 41. Figure 42.
PAGE 5
STM6600, STM6601 1 Description Description The STM6600-01 devices monitor the state of connected push-button(s) as well as sufficient supply voltage. An enable output controls power for the application through the MOSFET transistor, DC-DC converter, regulator, etc. If the supply voltage is above a precise voltage threshold, the enable output can be asserted by a simple press of the button. Factoryselectable supply voltage thresholds are determined by highly accurate and temperaturecompensated references.
PAGE 6
Description STM6600, STM6601 Figure 2. Basic functionality (option with enable deassertion after long push) POWER-UP(1) INTERRUPT (short push) POWER-DOWN (long push) PB SR EN INT interrupt interrupt AM00243v1 1. For power-up the battery voltage has to be above VTH+ threshold. Figure 3. Basic functionality (option with RST assertion after long push) INTERRUPT (short push) POWER-UP(1) POWER-DOWN (long push) PB SR RST INT interrupt interrupt AM00243bv1 1.
PAGE 7
STM6600, STM6601 Table 2. Description Pin descriptions Pin number Symbol 1 VCC Power supply input 2 SR Smart Reset™ button input 3 VREF 4 PSHOLD 5 CSRD 6 PB 7 VCCLO Output for high threshold comparator output (VTH+) 8 PBOUT Status of PB push-button input 9 EN or EN Enable output 10 RST Reset output 11 INT Interrupt output 12 GND Ground Figure 5. Function Precise 1.
PAGE 8
Description Figure 6. STM6600, STM6601 Block diagram VCC LO VCC VCC (1) RPB PB (2) RSR EN (EN) VCC + + – – VTH+ RST tREC generator PSHOLD VTH– Smart logic Glitch immunity Edge detector debounce (3) RPSHOLD INT SR Glitch immunity Edge detector debounce VREF GND SRD logic PBOUT 1.5 V CSRD AM00237v3 1. Internal pull-up resistor connected to PB input (see Table 5 for precise specifications). 2.
PAGE 9
STM6600, STM6601 2 Pin descriptions Pin descriptions VCC - power supply input VCC is monitored during startup and normal operation for sufficient voltage level. Decouple the VCC pin from ground by placing a 0.1 µF capacitor as close to the device as possible. SR - Smart Reset™ button input This input is equipped with voltage detector with a factory-trimmed threshold and has ±8 kV HBM ESD protection.
PAGE 10
Pin descriptions STM6600, STM6601 PB - power ON switch This input is equipped with a voltage detector with a factory-trimmed threshold and has ± 8 kV HBM ESD protection. When the PB button is pressed and held, the battery voltage is detected and EN (or EN) is asserted if the battery voltage is above the threshold VTH+ during the whole tDEBOUNCE period (see Figure 13).
PAGE 11
STM6600, STM6601 Pin descriptions EN or EN - enable output This output is intended to enable system power (see Figure 1). EN is asserted high after a valid turn-on event has been detected and confirmed (i.e. push-button has been pressed and held for tDEBOUNCE or more and VCC > VTH+ voltage level has been detected - see Figure 13).
PAGE 12
Operation 3 STM6600, STM6601 Operation The STM6600-STM6601 simplified smart push-button on/off controller with Smart Reset™ and power-on lockout enables and disables power for the application depending on pushbutton states, signals from the processor, and battery voltage. Power-on Because most of the processors have outputs in high-Z state before initialization, an internal pull-down resistor is connected to PSHOLD input during startup (see Figure 7, 8, 9, 10, 11, 12, 13, and 18).
PAGE 13
STM6600, STM6601 Operation If an undervoltage condition is detected for tDEBOUNCE + tINT_Min + tSRD, the enable output is deasserted (see Figure 21).
PAGE 14
Waveforms STM6600, STM6601 4 Waveforms Figure 7. Successful power-up on STM6600 (PB released prior to tON_BLANK expiration) processor sets PSHOLD Push-button pressed and PB connected to GND PB released prior to t ON_BLANK expiration PSHOLD state detected as high EN remains asserted VCC undervoltage detection ignored PSHOLD ignored internal pull-down resistor connected to PSHOLD input PB(1) PSHOLD(2) EN(3) RST tDEBOUNCE tREC tON_BLANK Note: INT signal is held high during power-up (i.e.
PAGE 15
STM6600, STM6601 Figure 8. Waveforms Successful power-up on STM6600 (tON_BLANK expires prior to PB release) Push-button pressed and PB connected to GND processor sets PSHOLD tON_BLANK expired prior to PB release PSHOLD state detected as high EN remains asserted PB released VCC undervoltage detection ignored PSHOLD ignored internal pull-down resistor connected to PSHOLD input PB(1) PSHOLD(2) EN(3) RST tDEBOUNCE tREC tON_BLANK Note: INT signal is held high during power-up (i.e.
PAGE 16
Waveforms Figure 9. STM6600, STM6601 Unsuccessful power-up on STM6600 (PB released prior to tON_BLANK) PB released PSHOLD state detected as low EN deasserted Push-button pressed and PB connected to GND VCC undervoltage detection ignored PSHOLD ignored internal pull-down resistor connected to PSHOLD input PB(1) PSHOLD(2) PB status ignored EN(3) RST tDEBOUNCE tEN_OFF tREC tON_BLANK Note: INT signal is held high during power-up (i.e. until PB release in this case). VCC is considered VCC > VTH+.
PAGE 17
STM6600, STM6601 Waveforms Figure 10. Unsuccessful power-up on STM6600 (tON_BLANK expires prior to PB release) tON_BLANK expired prior to PB release PSHOLD state detected as low EN is deasserted Push-button pressed and PB connected to GND PB (1) PB released VCC undervoltage detection ignored PB status ignored PSHOLD ignored internal pull-down resistor connected to PSHOLD input PSHOLD(2) EN(3) RST tDEBOUNCE tEN_OFF tREC tON_BLANK Note: INT signal is held high during power-up (i.e.
PAGE 18
Waveforms STM6600, STM6601 Figure 11. Successful power-up on STM6601 tON_BLANK expires processor PSHOLD state detected as high sets PSHOLD EN remains asserted Push-button pressed and PB connected to GND PB PB status and V CC undervoltage detection ignored (1) PSHOLD ignored (2) PSHOLD EN internal pull-down resistor connected to PSHOLD input (3) RST t DEBOUNCE t REC t ON_BLANK Note: INT signal is held high during power-up (i.e. until tON_BLANK expires in the case of the STM6601).
PAGE 19
STM6600, STM6601 Waveforms Figure 12. Unsuccessful power-up on STM6601 tON_BLANK expires PSHOLD state detected as low Push-button pressed and PB connected to GND EN deasserted Push-button pressed and PB connected to GND (1) PB PSHOLD ignored (2) PSHOLD intenal pull-down resistor connected to PSHOLD input (3) EN RST t DEBOUNCE t REC Note: INT signal is held high during power-up (i.e. until tON_BLANK expires in the case of the STM6601). VCC is considered VCC > VTH+. AM00238v2 1.
PAGE 20
Waveforms STM6600, STM6601 Figure 13. Power-up on STM660x with voltage dropout Push-button pressed and PB connected to GND VCC goes above VTH+ and tDEBOUNCE is counted again VTH+ VTH– VCC VCC LO VCC–Min VCC undervoltage detected VCC drop (1) PB (2) PSHOLD INT internal pull-down resistor connected to PSHOLD input (3) INT signal is held high during power-up EN RST < t DEBOUNCE t DEBOUNCE tREC < t ON_BLANK AM00249v2 1. PB detection on falling and rising edges. 2.
PAGE 21
STM6600, STM6601 Waveforms Figure 14. PB interrupt processor interrupt starts power-down sequence processor sets PSHOLD low Push-button pressed and PB connected to GND PB and EN is deasserted accordingly PB status ignored (1) PSHOLD PB status ignored VCC undervoltage detection ignored t DEBOUNCE t INT_Min Note: VCC is considered VCC > VTH+. tEN_OFF AM00251v2 1. PB detection on falling edge.
PAGE 22
Waveforms STM6600, STM6601 Figure 15. Long push, PB pressed first Push-button PB is pressed PB Push-button tSRD starts to SR is pressed be counted tSRD tDEBOUNCE set by CSRD tDEBOUNCE SR INT PB status ignored tINT_Min AM00257v1 Figure 16.
PAGE 23
STM6600, STM6601 Waveforms Figure 17.
PAGE 24
Waveforms STM6600, STM6601 Figure 18.
PAGE 25
STM6600, STM6601 Waveforms Figure 19.
PAGE 26
Waveforms STM6600, STM6601 Figure 20. Undervoltage detected for
PAGE 27
STM6600, STM6601 Waveforms Figure 22. PBOUT output waveform
PAGE 28
Typical operating characteristics 5 STM6600, STM6601 Typical operating characteristics Figure 23. Supply current vs. temperature, normal state 7.0 Supply current, ICC (µA) 6.5 6.0 5.5 5.0 4.5 VCC = 5.5 V 4.0 VCC = 3.6 V VCC = 2.0 V 3.5 3.0 -40 -20 0 20 40 60 80 Temperature, TA (°C) AM04701v1 Figure 24. Supply current vs. temperature, standby state 2.0 Supply current, ICC (µA) VCC = 5.5 V VCC = 3.6 V 1.5 VCC = 2.0 V 1.0 0.5 0.
PAGE 29
STM6600, STM6601 Typical operating characteristics Figure 25. Supply current vs. supply voltage, normal state 7 Supply current, ICC (µA) 6 5 4 3 TA = 85 °C 2 TA = 25 °C TA = 0 °C 1 TA = –40 °C 0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 Supply voltage, VCC (V) AM04703v1 Figure 26. Supply current vs. supply voltage, standby state 1.5 Supply current, ICC (µA) TA = 85 °C TA = 25 °C TA = 0 °C 1.0 TA = –40 °C 0.5 0.0 2.0 2.5 3.0 3.5 4.0 Supply voltage, VCC (V) Doc ID 15453 Rev 11 4.5 5.
PAGE 30
Typical operating characteristics STM6600, STM6601 Figure 27. Threshold vs. temperature, VTH+ = 3.4 V (typ.) 3.50 Threshold, V TH+ (V) 3.45 3.40 3.35 3.30 3.25 3.20 -40 -20 0 20 40 60 80 Tem perature, T A (°C) AM04705v1 Figure 28. Threshold hysteresis vs. temperature, VHYST = 200 mV (typ.
PAGE 31
STM6600, STM6601 Typical operating characteristics Figure 29. Debounce period vs. supply voltage Debounce period, tDEBOUNCE (ms) 45 40 35 30 TA = 85 °C 25 TA = 25 °C TA = 0 °C 20 TA = –40 °C 15 3.5 4 4.5 5 5.5 Supply voltage, VCC (V) AM04707v1 Figure 30. CSRD charging current vs. temperature, VCC = 3.6 V 200 CSRD charging current, ISRD (nA) 190 180 170 160 150 140 130 VCC = 5.5 V 120 VCC = 3.
PAGE 32
Typical operating characteristics STM6600, STM6601 Figure 31. Output low voltage vs. output low current, TA = 25 °C Output low voltage, VOL (V) 0.30 VCC =1.6V 0.25 VCC =3.6V 0.20 VCC =5.5V 0.15 0.10 0.05 0.00 0 1 2 3 4 5 Output low current, IOL (mA) Note: AM04709v1 Characteristics valid for all the outputs (EN, EN, RST, INT, PBOUT and VCCLO). Figure 32. Output high voltage vs. output high current, TA = 25 °C 0.8 Output high voltage, VCC - VOH (V) VCC=1.6V VCC=3.6V 0.6 VCC=5.5V 0.4 0.
PAGE 33
STM6600, STM6601 Typical operating characteristics Figure 33. Output voltage vs. supply voltage, IOUT = 1 mA, TA = 25 °C 1 Output voltage, VOUT (V) 0.8 0.6 0.4 0.2 0 0 1 2 3 4 5 Supply voltage, VCC (V) Note: AM04711v1 Characteristics valid for all the outputs (EN, EN, RST, INT, PBOUT and VCCLO). Figure 34. Input voltage vs. temperature 1.05 VCC = 3.6 V 1.04 Input voltage, VIN (V) VCC = 5.5 V 1.03 1.02 1.01 1.00 0.
PAGE 34
Typical operating characteristics STM6600, STM6601 Figure 35. Reference output voltage vs. temperature, VCC = 2.0 V 1.520 Reference output voltage, VREF (V) 1.515 IREF = 0 mA 1.510 IREF = 15 µA 1.505 1.500 1.495 1.490 1.485 1.480 -40 -20 0 20 40 60 80 Temperature, TA (°C) Note: AM04713v1 1 µF capacitor is connected to the VREF pin. Figure 36. Reference output voltage vs. load current, VCC = 2.0 V, TA = 25 °C Reference output voltage, VREF (V) 1.6 1.5 1.4 1.3 1.2 1.
PAGE 35
STM6600, STM6601 Typical operating characteristics Figure 37. Reference output voltage vs. supply voltage, TA = 25 °C 1.520 Reference output voltage, VREF (V) 1.515 1.510 1.505 1.500 1.495 IREF = 0 µA 1.490 IREF = 15 µA 1.485 1.480 2 2.5 3 3.5 4 Supply voltage, VCC (V) Note: 4.5 5 5.5 AM04715v1 1 µF capacitor is connected to the VREF pin. Figure 38. Reference startup, IREF = 15 µF, TA = 25 °C Note: 1 µF capacitor is connected to the VREF pin.
PAGE 36
Typical operating characteristics STM6600, STM6601 Figure 39. Reference response to steps on supply voltage, IREF = 15 µA, TA = 25 °C Note: 36/52 1 Supply voltage goes from 3.6 V to 5.5 V and back to 3.6 V, ramp 1 V / 100 ns. 2 1 µF capacitor is connected to the VREF pin.
PAGE 37
STM6600, STM6601 Typical operating characteristics Figure 40. Reference response to steps in load current, VCC = 3.6 V, TA = 25 °C Note: 1 Supply voltage goes from 0 µA to 15 µA and back to 0 µA, ramp 1 µA / 100 ns. 2 1 µF capacitor is connected to the VREF pin.
PAGE 38
Maximum ratings 6 STM6600, STM6601 Maximum ratings Stressing the device above the rating listed inTable 3 may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in Table 4 of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Table 3. Symbol VCC Absolute maximum ratings Parameter Min. Max.
PAGE 39
STM6600, STM6601 7 DC and AC characteristics DC and AC characteristics This section summarizes the operating measurement conditions and the DC and AC characteristics of the device. The parameters inTable 5 that follow are derived from tests performed under the measurement conditions summarized in Table 4. Designers should check that the operating conditions in their circuit match the operating conditions when relying on the quoted parameters. Table 4.
PAGE 40
DC and AC characteristics Table 5. Symbol STM6600, STM6601 DC and AC characteristics (continued) Parameter Test condition(1) Min. Typ.(2) Max. Unit 0.99 V PB VIL Input low voltage VCC ≥ 2.0 V, enable asserted VIH Input high voltage VCC ≥ 2.0 V, enable asserted tDEBOUNCE Debounce period RPB Internal pull-up resistor VIL Input low voltage VIH Input high voltage 1.05 V VCC ≥ 2.0 V 20 32 44 ms VCC = 5.5 V, input asserted 65 100 135 kΩ 0.99 V SR 1.
PAGE 41
STM6600, STM6601 Table 5. Symbol DC and AC characteristics DC and AC characteristics (continued) Parameter Test condition(1) Min. Typ.(2) Max. Unit 100 150 200 nA CSRD ISRD C SRD charging current VSRD C SRD voltage threshold VCC = 3.6 V, load on VREF pin 100 kΩ and mandatory 1 µF capacitor, TA = 25 °C 1.
PAGE 42
Package mechanical data 8 STM6600, STM6601 Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark.
PAGE 43
STM6600, STM6601 Package mechanical data Figure 41. TDFN12 (2 x 3 mm) package outline D A B INDEX AREA 0.10 C 2x E (D/2xE/2) 0.10 C TOP VIEW A A1 0.10 C C SEATING PLANE SIDE VIEW 0.08 C e b 1 6 12 7 0.10 C A B PIN#1 ID INDEX AREA L (D/2xE/2) BOTTOM VIEW 8070542_A Table 6. TDFN12 (2 x 3 mm) package mechanical data mm inches Symbol Min. Typ. Max. Min. Typ. Max. A 0.70 0.75 0.80 0.028 0.030 0.031 A1 0.00 0.02 0.05 0.000 0.001 0.002 b 0.15 0.20 0.25 0.006 0.
PAGE 44
Package mechanical data STM6600, STM6601 Figure 42. TDFN12 (2 x 3 mm) recommended footprint X X X X X X X X $IMENSIONS MM INCHES !- Note: 44/52 Drawing not to scale.
PAGE 45
STM6600, STM6601 Package mechanical data Figure 43. Carrier tape for TDFN12 (2 x 3 mm) package P0 E P2 D T A0 F TOP COVER TAPE W B0 P1 CENTER LINES OF CAVITY K0 USER DIRECTION OF FEED AM03073v1 Table 7. Carrier tape dimensions for TDFN12 (2 x 3 mm) package Package W D TDFN12 12.00 ±0.30 1.50 +0.10/ –0.00 E P0 P2 F 1.75 4.00 2.00 5.50 ±0.10 ±0.10 ±0.10 ±0.05 A0 B0 K0 P1 T 2.30 ±0.10 3.20 ±0.10 1.10 ±0.01 4.00 ±0.10 0.30 ±0.05 Doc ID 15453 Rev 11 Unit Bulk qty.
PAGE 46
Part numbering STM6600, STM6601 9 Part numbering Table 8.
PAGE 47
STM6600, STM6601 Table 8. Part numbering STM6600 ordering information scheme (continued) Example: STM660 0 F Q 2 4 DM 6 F Package DM: TDFN12 Temperature range 6: –40 °C to +85 °C Shipping method F: ECOPACK® package, tape and reel 1. Other options are offered. Minimum order quantities may apply. Please contact local ST sales office for availability.
PAGE 48
Part numbering Table 9.
PAGE 49
STM6600, STM6601 Product selector 10 Product selector Table 10. STM6600 product selector Full part number EN or EN(1) Internal Power-on Forced tON_BLANK After resistor lockout power-off (s) long voltage on SR voltage at startup (2) push VTH+ (V) VTH- (V) input (min.) tON_BLANK (s) at reset (min.) Top marking(3) STM6600AS24DM6F EN RST pull-up 3.40 3.20 5.6 5.6 pyww AS24 STM6600BQ24DM6F EN RST pull-up 3.30 3.10 5.6 5.6 pyww BQ24 STM6600CS25DM6F EN EN pull-up 3.40 3.20 11.
PAGE 50
Product selector Table 11. STM6600, STM6601 STM6601 product selector Full part number EN or EN(1) Internal Power-on Forced tON_BLANK tON_BLANK After Top resistor lockout power-off (s) (s) long marking(3) voltage on SR voltage at startup at reset (2) push VTH+ (V) VTH- (V) input (min.) (min.) STM6601AQ2BDM6F EN RST pull-up 3.30 3.10 1.4 1.4 pyww AQ2B STM6601AU2DDM6F EN RST pull-up 3.50 3.30 5.6 5.6 pyww AU2D STM6601BM2DDM6F EN RST pull-up 3.10 2.90 5.6 5.
PAGE 51
STM6600, STM6601 11 Revision history Revision history Table 12. Document revision history Date Revision 04-Mar-2009 1 Initial release. 05-Jun-2009 2 Updated text in Section 2, Section 3, Figure 11, 12; updated Figure 1, 7, 9, 14, 18, 19, 43, Table 3, 5, 8, 9, 10; added Figure 8, 10, Table 7; reformatted document. 23-Jul-2009 3 Updated text in Features, Table 1, 8, 9, and 10; reformatted document.
PAGE 52
STM6600, STM6601 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale.