Datasheet

ManualsBrandsSTMICROELECTRONICS ManualsDiodesSMTPA180

June 2007 Rev 3 1/11

SMP50 / SMTPA / TPA

Trisil™ for telecom equipment protection

Features

■ Bidirectional crowbar protection

■ Voltage range from 62 V to 320 V

■ Low capacitance from 12 pF to 20 pF @ 50 V

■ Low leakage current : I

= 2 µA max

■ Holding current: I

= 150 mA min

■ Repetitive peak pulse current :

= 50 A (10/1000 µs)

Main applications

Telecommunication equipment such as:

■ Analog and digital line cards (xDSL, T1/E1,

ISDN, ...)

■ Terminals (phone, fax, modem, ...) and central

office equipment

Description

These Trisil series have been designed to protect

telecommunication equipment against lightning

and transient induced by AC power lines.

They are available in SMA, SMB and DO-15

packages.

Benefits

Trisils are not subject to ageing and provide a fail

safe mode in short circuit for a better protection.

They are used to help equipment to meet various

standards such as UL1950, IEC950 / CSA C22.2,

UL1459 and FCC part 68.

Trisils have UL94 V0 approved resin.

SMA and SMB packages are JEDEC registered

(DO-214AC and DO-214AA).

Trisils are UL497B approved (file: E136224).

TM: TRISIL is a trademark of STMicroelectronics

Order codes

Schematic Diagram

Part Number Marking

SMP50-xxx

See Ordering Information

on page 9

TPAxxx

SMTPAxxx

SMA

(JEDEC DO-214AC)

SMP50

SMB

(JEDEC DO-214AA)

SMTPA

DO-15

TPA

www.st.com

Summary of content (11 pages)

PAGE 1
SMP50 / SMTPA / TPA Trisil™ for telecom equipment protection Features ■ Bidirectional crowbar protection ■ Voltage range from 62 V to 320 V ■ Low capacitance from 12 pF to 20 pF @ 50 V ■ Low leakage current : IR = 2 µA max ■ Holding current: IH = 150 mA min ■ Repetitive peak pulse current : IPP = 50 A (10/1000 µs) SMB SMA (JEDEC DO-214AC) (JEDEC DO-214AA) SMTPA SMP50 Main applications Telecommunication equipment such as: ■ Analog and digital line cards (xDSL, T1/E1, ISDN, ...
PAGE 2
Characteristics 1 SMP50 / SMTPA / TPA Characteristics Table 1. Compliant with the following standards Standard Peak Surge Voltage (V) Waveform Voltage Required peak current (A) Current waveform Minimum serial resistor to meet standard (Ω) GR-1089 Core First level 2500 1000 2/10 µs 10/1000 µs 500 100 2/10 µs 10/1000 µs 20 10 GR-1089 Core Second level 5000 2/10 µs 500 2/10 µs 40 GR-1089 Core Intra-building 1500 2/10 µs 100 2/10 µs 0 ITU-T-K20/K21 6000 1500 10/700 µs 150 37.
PAGE 3
SMP50 / SMTPA / TPA Table 3. Characteristics Thermal resistances Value Symbol Parameter Unit DO-15 SMA SMB Rth(j-a) Junction to ambient (with recommended footprint or with Llead = 10 mm for DO-15) 100 120 100 °C/W Rth(j-l) Junction to leads (Llead = 10 mm for DO-15) 60 30 20 °C/W Table 4.
PAGE 4
Characteristics Table 5. SMP50 / SMTPA / TPA Electrical characteristics - values (Tamb = 25°C) Types IRM @ VRM max. µA Dynamic VBO(2) Static VBO @ IBO(3) IH(4) C(5) C(6) max. max. max. min. typ. typ. V V V mA mA pF pF IR @ VR(1) max.
PAGE 5
SMP50 / SMTPA / TPA Figure 3. Characteristics On-state voltage versus on-state current (typical values) Figure 4. IT(A) Relative variation of holding current versus junction temperature IH[Tj] / IH[Tj=25°C] 2.0 50 1.8 1.6 Tj=25°C 20 1.4 1.2 10 1.0 5 0.8 0.6 0.4 2 0.2 VT(V) Tj(°C) 0.0 1 0 1 2 Figure 5. 3 4 5 6 7 8 9 10 Relative variation of breakover voltage versus junction temperature -40 -20 Figure 6.
PAGE 6
Characteristics Figure 9. SMP50 / SMTPA / TPA Test circuit 1 for Dynamic IBO and VBO parameters 100 V / µs, di /dt < 10 A / µs, Ipp = 50 A 2Ω 83 Ω 45 Ω 10 µF U 66 Ω 46 µH 0.36 nF 470 Ω KeyTek 'System 2' generator with PN246I module 1 kV / µs, di /dt < 10 A / µs, Ipp = 10 A 250 Ω 26 µH 60 µF U 46 µH 47 Ω 12 Ω KeyTek 'System 2' generator with PN246I module Figure 10.
PAGE 7
SMP50 / SMTPA / TPA 2 Ordering information scheme Ordering information scheme SMP 50 - xxx Series SMP = Trisil surface mount in SMA SMTP = Trisil surface mount in SMB TP = Trisil in DO-15 Repetitive Peak Pulse Current A or 50 = 50 A Voltage 62 = 62 V 3 Package information ● Epoxy meets UL94, V0 Table 6. SMA dimensions Dimensions Ref. Millimeters Inches E1 D E A1 A2 C L Min. Max. Min. Max. A1 1.90 2.45 0.075 0.094 A2 0.05 0.20 0.002 0.008 b 1.25 1.65 0.049 0.065 c 0.
PAGE 8
Package information Table 7. SMP50 / SMTPA / TPA SMB dimensions Dimensions Ref. Millimeters Inches E1 D E A1 A2 C L b Min. Max. Min. Max. A1 1.90 2.45 0.075 0.096 A2 0.05 0.20 0.002 0.008 b 1.95 2.20 0.077 0.087 c 0.15 0.40 0.006 0.016 E 5.10 5.60 0.201 0.220 E1 4.05 4.60 0.159 0.181 D 3.30 3.95 0.130 0.156 L 0.75 1.50 0.030 0.059 Figure 13. Footprint, dimensions in mm (inches) 1.62 2.60 (0.064) (0.102) 1.62 (0.064) 2.18 (0.086) 5.84 (0.300) Table 8.
PAGE 9
SMP50 / SMTPA / TPA 4 Ordering Information Ordering Information Part Number Marking SMP50-62 V06 SMP50-68 V07 SMP50-100 V10 SMP50-120 V12 SMP50-130 V13 SMP50-180 V18 SMP50-200 V20 SMP50-220 V22 SMP50-240 V24 SMP50-270 V27 SMP50-320 V32 SMTPA62 U01 SMTPA68 U05 SMTPA100 U13 SMTPA120 U17 SMTPA130 U19 SMTPA180 U25 SMTPA200 U27 SMTPA220 U31 SMTPA240 U35 SMTPA270 U39 SMTPA320 U47 TPA62 TPA62RL TPA68 TPA68RL TPA100 TPA100RL TPA120 TPA130 TPA130RL TPA180 TPA180RL TPA
PAGE 10
Revision History 5 10/11 SMP50 / SMTPA / TPA Revision History Date Revision Description of Changes 16-Nov-2004 1 SMP50, SMTPA and TPA datasheets merge. 30-Mar-2007 2 Reformatted to current standards. Updated IPP value in Table 2 . Added part numbers SMP50-320 and SMTPA320. Updated dimensions and footprint for SMA and footprint for SMB. 12-Jun-2007 3 Corrected typographical error in part number. Added dimensions in inches to footprint illustrations.
PAGE 11
SMP50 / SMTPA / TPA Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale.