User's Manual
Table Of Contents
- 1 Features
- 2 Ordering information
- 3 Development environment
- 4 Conventions
- 5 Delivery recommendations
- 6 Hardware layout and configuration
- 6.1 Power supply management
- 6.2 Clocks
- 6.3 Reset sources
- 6.4 User buttons and LEDs
- 6.5 Physical input devices: buttons
- 6.6 Boot options
- 6.7 Embedded ST-LINK/V2-1
- 6.8 ETM TRACE Mictor-38 connector
- 6.9 JTAG connector
- 6.10 DDR3L
- 6.11 eMMC
- 6.12 NAND Flash memory
- 6.13 Quad-SPI NOR Flash memory
- 6.14 microSD card
- 6.15 Audio
- 6.16 DSI LCD
- 6.17 Camera
- 6.18 1 Gbps Ethernet
- 6.19 USB OTG HS
- 6.20 USB host
- 6.21 RS-232 port
- 6.22 CAN FD
- 6.23 Smartcard
- 6.24 ADC/DAC
- 6.25 I2C_EXT connector
- 6.26 MFX MCU
- 6.27 Motor control
- 6.28 GPIO 40-pin expansion connector
- 6.29 RGB LTDC connector
- 7 STM32MP157F-EV1 Evaluation board information
- Appendix B STM32MP157F-EV1 I/O assignment
- Appendix C Federal Communications Commission (FCC) and ISED Canada Compliance Statements
- Appendix D CE conformity
- Revision history
- Contents
- List of tables
- List of figures
I/O Bridge
Setting
(1)
Comment
PK1
SB40
OFF
PK1 is not connected to Trace
PK1 may be used for L
TDC_G6
PK2
SB39
ON PK2 may be used for the trace function TRACE_D5
OFF
PK2 is not connected to Trace
PK2 may be used for L
TDC_G7
PK5
SB49
ON PK5 may be used for the trace function TRACE_D6
OFF
PK5 is not connected to Trace
PK5 may be used for L
TDC_B6
PK6
SB35
ON PK6 may be used for the trace function TRACE_D7
OFF
PK6 is not connected to Trace
PK6 may be used for L
TDC_B7
PJ0
SB34
ON PJ0 may be used for the trace function TRACE_D8
OFF
PJ0 is not connected to Trace
PJ0 may be used for L
TDC_R1
PJ1 SB37
ON PJ1 may be used for the trace function TRACE_D9
OFF
PJ1 is not connected to Trace
PJ1 may be used for L
TDC_R2
PJ2 SB48
ON PJ2 may be used for the trace function TRACE_D10
OFF
PJ2 is not connected to Trace
PJ2 may be used for L
TDC_R3
PJ3 SB47
ON PJ3 may be used for the trace function TRACE_D11
OFF
PJ3 is not connected to Trace
PJ3 may be used for L
TDC_R4
PJ4 SB46
ON PJ4 may be used for the trace function TRACE_D12
OFF
PJ4 is not connected to Trace
PJ4 may be used for L
TDC_R5
PJ7 SB45
ON PJ7 may be used for the trace function TRACE_D13
OFF
PJ7 is not connected to Trace
PJ7 may be used for L
TDC_G0
PJ8 SB44
ON PJ8 may be used for the trace function TRACE_D14
OFF
PJ8 is not connected to Trace
PJ8 may be used for L
TDC_G1
PJ9 SB50
ON PJ9 may be used for the trace function TRACE_D15
OFF
PJ9 is not connected to Trace
PJ9 may be used for L
TDC_G2
1.
Default configuration is shown in bold
Figure 10 shows the TRACE Mictor-38 connector
UM2648
ETM TRACE Mictor-38 connector
UM2648 - Rev 1
page 18/61